Characterization of Al2(WO4)3 Synthesized by Co-Precipitation Method

2014 ◽  
Vol 798-799 ◽  
pp. 85-89 ◽  
Author(s):  
E.S.G. Junior ◽  
P.M . Jardim
Keyword(s):  
Precipitation Method ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Tem Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Co Precipitation ◽  
Alpha Alumina

Al2(WO4)3was synthesized by co-precipitation using Na2WO4and Al (NO3)3as precursors. After drying the precipitate, it was calcined at different temperatures between 500°C and 800°C. The crystallization and degradation temperatures of the samples were evaluated by means of Differential Scanning Calorimetry (DSC), Thermogravimetry (TG) and X-Ray Diffraction (XRD). It was observed that the crystallization starts at around 600°C, however Transmission Electron Microscopy (TEM) analysis showed that at this temperature the sample is partially amorphous. The degradation of the material starts at around 1200°C and at 1400°C the tungsten oxide has almost completely evaporated and the material is transformed mainly in alpha-alumina.

Synthesis and Characterization of Structure of Fe3O4@Graphene Oxide Nanocomposites

2016 ◽  
Vol 25 (6) ◽  
pp. 096369351602500 ◽  
Author(s):  
Ruimin Fu ◽  
Mingfu Zhu
Keyword(s):  
Graphene Oxide ◽  
Drug Carrier ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
Co Precipitation ◽  
Ft Ir Spectroscopy

Nowadays, the hummers method for preparation of graphene oxide (GO) was improved. The grapheme oxide @ Fe3O4 magnetic nanocomposites were synthesized by co-precipitation method. After analysing the morphology and structure of obtained nanocomposites by X-ray diffraction (XRD), transmission electron microscope (TEM) and Fourier transform infrared (FT-IR) spectroscopy, the result was shown as follows. The particle size of Fe3O4 in nanocomposites is 30 nm. Many functional groups are found in grapheme oxide, and such groups could be used to bind with the drug. In the test for magnetic properties, the nanocomposites gathered rapidly in the vicinity of the permanent magnet. The nanocomposites, with high superparamagnetism, can be used in the following applications: drug targeting transports, drug carrier, and diagnosis assistant system.

Synthesis Mechanism and Microstructure Characterization of BaIn2O4

2011 ◽  
Vol 347-353 ◽  
pp. 1342-1347 ◽  
Author(s):  
Ping Ren ◽  
Li Cheng Zhou ◽  
Jun Xi Zhang ◽  
Hong Yun
Keyword(s):  
Sintering Temperature ◽  
Precipitation Method ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Synthesis Mechanism ◽  
X Ray ◽  
Grain Sizes ◽  
Co Precipitation

The synthesis mechanism and microstructures of BaIn2O4 particles were analyzed by simultaneous thermogravimetry - differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), and scanning electron microscope (SEM). Firstly, In(OH)3 and BaCO3 precursors were prepared by the co-precipitation method. Next, during the sintering process In(OH)3 initially decomposed into In2O3 and water, and then BaCO3 reacted with In2O3 to synthesize Ba4In6O13. Finally, Ba4In6O13 and In2O3 further reacted to form BaIn2O4. The obtained BaIn2O4 particles were in monoclinic structure and exhibited high crystal quality. The grains were tightly bound together and their boundaries became blurry. The grain sizes increased with increasing the sintering temperature.

Microstructure Characterization of Metal Mixed Oxides

MRS Advances ◽  
2017 ◽  
Vol 2 (64) ◽  
pp. 4025-4030 ◽  
Author(s):  
T. Kryshtab ◽  
H. A. Calderon ◽  
A. Kryvko
Keyword(s):  
Mixed Oxides ◽  
Profile Analysis ◽  
Atomic Resolution ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Reconstruction Procedure ◽  
Transmission Electron ◽  
Xrd Patterns ◽  
Co Precipitation

ABSTRACTThe microstructure of Ni-Mg-Al mixed oxides obtained by thermal decomposition of hydrotalcite-like compounds synthesized by a co-precipitation method has been studied by using X-ray diffraction (XRD) and atomic resolution transmission electron microscopy (TEM). XRD patterns revealed the formation of NixMg1-xO (x=0÷1), α-Al2O3 and traces of MgAl2O4 and NiAl2O4 phases. The peaks profile analysis indicated a small grain size, microdeformations and partial overlapping of peaks due to phases with different, but similar interplanar spacings. The microdeformations point out the presence of dislocations and the peaks shift associated with the presence of excess vacancies. The use of atomic resolution TEM made it possible to identify the phases, directly observe dislocations and demonstrate the vacancies excess. Atomic resolution TEM is achieved by applying an Exit Wave Reconstruction procedure with 40 low dose images taken at different defocus. The current results suggest that vacancies of metals are predominant in MgO (NiO) crystals and that vacancies of Oxygen are predominant in Al2O3 crystals.

Template Induced Synthesis of Nano-Hydroxyapatite by Co-Precipitation Method

2011 ◽  
Vol 311-313 ◽  
pp. 1713-1716 ◽  
Author(s):  
Yan Rong Sun ◽  
Tao Fan ◽  
Chang An Wang ◽  
Li Guo Ma ◽  
Feng Liu
Keyword(s):  
Electron Microscope ◽  
Chondroitin Sulfate ◽  
Aspartic Acid ◽  
Transmission Electron Microscope ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structure And Morphology ◽  
Transmission Electron ◽  
Co Precipitation

Nano-hydroxyapatite with different morphology was synthesized by the co-precipitation method coupled with biomineralization using Ca(NO3)2•4H2O and (NH4)2HPO4 as reagents, adding chondroitin sulfate, agarose and aspartic acid as template. The structure and morphology of the prepared powders were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM).

The Influence of Calcination Temperature on Quantitative Phase of Hematite from Iron Stone Tanah Laut

2015 ◽  
Vol 1112 ◽  
pp. 489-492
Author(s):  
Ali Mufid ◽  
M. Zainuri
Keyword(s):  
Particle Size ◽  
Calcination Temperature ◽  
Thermo Gravimetric Analysis ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Particle Size Analyzer ◽  
Co Precipitation

This research aims to form particles of hematite (α-Fe2O3) with a basis of mineral iron ore Fe3O4 from Tanah Laut. Magnetite Fe3O4 was synthesized using co-precipitation method. Further characterization using X-ray fluorescence (XRF) to obtain the percentage of the elements, obtained an iron content of 98.51%. Then characterized using thermo-gravimetric analysis and differential scanning calorimetry (TGA-DSC) to determine the calcination temperature, that at a temperature of 445 °C mass decreased by 0.369% due to increase in temperature. Further Characterization of X-ray diffraction (XRD) to determine the phases formed at the calcination temperature variation of 400 °C, 445 °C, 500 °C and 600 °C with a holding time of 5 hours to form a single phase α-Fe2O3 hematite. Testing with a particle size analyzer (PSA) to determine the particle size distribution, where test results indicate that the α-Fe2O3 phase of each having a particle size of 269.7 nm, 332.2 nm, 357.9 nm, 412.2 nm. The best quantity is shown at a temperature of 500 °C to form the hematite phase. This result is used as the calcination procedure to obtain a source of Fe ions in the manufacture of Lithium Ferro Phosphate.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

Preparation and characterization of iron oxide nanoparticles coated with chitosan for removal of Cd(II) and Cr(VI) from aqueous solution

2014 ◽  
Vol 70 (6) ◽  
pp. 1004-1010 ◽  
Author(s):  
Th. I. Shalaby ◽  
N. M. Fikrt ◽  
M. M. Mohamed ◽  
M. F. El Kady
Keyword(s):  
Electron Microscope ◽  
Magnetic Nanoparticles ◽  
Magnetic Nanomaterials ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Toxic Heavy Metals ◽  
Transmission Electron ◽  
Magnetite Fe3o4 ◽  
Co Precipitation

This study investigated the applicability of magnetite Fe3O4 nanoparticles coated with chitosan (CMNs) for the removal of some toxic heavy metals from simulated wastewater. Magnetic nanomaterials were synthesized using the co-precipitation method and characterized by transmission electron microscope, scanning electron microscope, X-ray diffraction, and Fourier transformer infrared spectroscopy. The magnetic properties of the prepared magnetic nanoparticles were determined by a vibrating-sample magnetometer. Batch experiments were carried out to determine the adsorption kinetics of Cr(VI) and Cd(II) by magnetic nanoparticles. It is noteworthy that CMNs show a highly efficient adsorption capacity for low concentration Cr(VI) and Cd(II) ions solution, which can reach 98% within 10 min.

Characterization of Nanocrystalline γ–Fe2O3Prepared by Wet Chemical Method

1999 ◽  
Vol 14 (4) ◽  
pp. 1570-1575 ◽  
Author(s):  
G. Ennas ◽  
G. Marongiu ◽  
A. Musinu ◽  
A. Falqui ◽  
P. Ballirano ◽  
...  
Keyword(s):  
Isothermal Treatment ◽  
X Ray Diffraction ◽  
Ferrous Chloride ◽  
Scanning Calorimetry ◽  
Direct Transformation ◽  
X Ray ◽  
Transmission Electron ◽  
Xrd Techniques ◽  
Kinetics Of

Homogeneous maghemite (γ–Fe2O3) nanoparticles with an average crystal size around 5 nm were synthesized by successive hydrolysis, oxidation, and dehydration of tetrapyridino-ferrous chloride. Morphological, thermal, and structural properties were investigated by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and x-ray diffraction (XRD) techniques. Rietveld refinement indicated a cubic cell. The superstructure reflections, related to the ordering of cation lattice vacancies, were not detected in the diffraction pattern. Kinetics of the solid-state phase transition of nanocrystalline maghemite to hematite (α–Fe2O3), investigated by energy dispersive x-ray diffraction (EDXRD), indicates that direct transformation from nanocrystalline maghemite to microcrystalline hematite takes place during isothermal treatment at 385 °C. This temperature is lower than that observed both for microcrystalline maghemite and for nanocrystalline maghemite supported on silica.

Synthesis of (Y,Gd)2O3:Eu nanopowder by a novel co-precipitation processing

2004 ◽  
Vol 19 (12) ◽  
pp. 3586-3591 ◽  
Author(s):  
Jiyang Chen ◽  
Ying Shi ◽  
Jianlin Shi
Keyword(s):  
Electron Microscopy ◽  
Ammonium Hydroxide ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Hydrogen Carbonate ◽  
Ammonium Hydrogen ◽  
Intense Luminescence ◽  
Co Precipitation

Nano-sized (Y,Gd)2O3:Eu powders were synthesized by a novel co-precipitation processing in which a mixture of ammonium hydroxide and ammonium hydrogen carbonate was adopted as a complex precipitant. Evolution behaviors of precursors during calcinations were studied by means of thermogravimetry-differential scanning calorimetry-mass spectrum, Fourier transform infrared, x-ray diffraction, scanning electron microscopy, and transmission electron microscopy in detail. Nano-sized (Y,Gd)2O3:Eu powder as prepared possessed a primary grain size of about 30 nm and specific surface area of 38 m2/g after being calcined at 850 °C for 2 h, showing much finer grains and less agglomeration. The as prepared nanopowder shows intense luminescence at 611nm under x-ray or ultraviolet excitation. Transparent (Y,Gd)2O3:Eu ceramics can also be fabricated using this high sinterable nanopowder.

Synthesis and Luminescence Properties of Yb3+/Ho3+ Co-Doped Lu2O3 Nanocrystalline Powders

2007 ◽  
Vol 280-283 ◽  
pp. 521-524
Author(s):  
Li Qiong An ◽  
Jian Zhang ◽  
Min Liu ◽  
Sheng Wu Wang
Keyword(s):  
Electron Microscopy ◽  
Upconversion Luminescence ◽  
Nanocrystalline Powders ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Excitation Spectra ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Co Doped

Yb3+ and Ho3+ co-doped Lu2O3 nanocrystalline powders were synthesized by a reversestrike co-precipitation method. The as-prepared powders were examined by the X-ray diffraction and transmission electron microscopy. The phase composition of the powders was cubic and the particle size was in the range of 30~50 nm. Emission and excitation spectra of the powders were measured by a spectrofluorometer and the possible upconversion luminescence mechanism was also discussed.

Sign in / Sign up

Export Citation Format

Share Document