scholarly journals Characteristics of Rotational Vibration of Cutting Edge in Elliptical Vibration Cutting by Modulation of Excitation Frequency

2011 ◽  
Vol 21 (3) ◽  
pp. 258-263 ◽  
Author(s):  
Byoung-Gook Loh ◽  
Gi-Dae Kim
Keyword(s):  
Excitation Frequency ◽  
Cutting Edge ◽  
Elliptical Vibration Cutting ◽  
Vibration Cutting ◽  
Elliptical Vibration ◽  
Rotational Vibration

scholarly journals Elliptical Vibration Cutting (1st Report)

1996 ◽  
Vol 62 (8) ◽  
pp. 1127-1131 ◽  
Author(s):  
Eiji SHAMOTO ◽  
Yoshiyuki MORIMOTO ◽  
Toshimichi MORIWAKI
Keyword(s):  
Elliptical Vibration Cutting ◽  
Vibration Cutting ◽  
Elliptical Vibration

Study on Feed Offset in Elliptical Vibration Cutting

2014 ◽  
Vol 490-491 ◽  
pp. 600-606
Author(s):  
Jie Qiong Lin ◽  
Jin Guo Han ◽  
Dan Jing ◽  
Xian Jing
Keyword(s):  
Surface Topography ◽  
Surface Quality ◽  
Simulation Analysis ◽  
Three Dimensional ◽  
Curved Surface ◽  
Elliptical Vibration Cutting ◽  
Vibration Cutting ◽  
Elliptical Vibration ◽  
Tool Edge

Elliptical vibration cutting (EVC) process and three dimensional cutting surfaces are analyzed in this paper to understand the formation of surface topography. The model of EVC surface topography is established based on curved surface remove function under the assumption that the tool edge is sharp enough. And simulation analysis of surface topography is conducted with different feed offset ratios. Results indicate that RMS change with feed offset ratios λ. The range of RMS is larger when feed offset ratio ranges from both 0 to 0.4 and 0.6 to 1, while the range is smaller when feed offset ratio changes from 0.4 to 0.6. Whats more, RMS reaches the minimum when feed offset ratio is 0.5. The present research provides some references for reducing the height of vibration ripples and improving EVC surface quality.

Development and optimization of ultrasonic elliptical vibration cutting device based on single excitation

2021 ◽  
pp. 1-29
Author(s):  
Sen Yin ◽  
Zhigang Dong ◽  
Yan Bao ◽  
Renke Kang ◽  
Wenhao Du ◽  
...  
Keyword(s):  
Cutting Speed ◽  
Tungsten Alloy ◽  
Asymmetric Structure ◽  
Diamond Cutting ◽  
Elliptical Vibration Cutting ◽  
Vibration Cutting ◽  
Elliptical Vibration ◽  
Technical Capability ◽  
Diamond Cutting Tool ◽  
Ultrasonic Elliptical Vibration

Abstract Ultrasonic elliptical vibration cutting (UEVC) technique, as an advanced cutting method, has been successfully applied to machine difficult-to-cut materials for the last decade. In this study, the mechanism of the elliptical vibration locus caused by the “asymmetric structure” of the horn was analyzed theoretically firstly, and the corresponding relationship between the degree of asymmetry and the elliptical vibration locus was determined based on finite element method (FEM). Then an efficient single-excitation UEVC device with “asymmetric structure” was developed and optimized. The resonant frequency of the device was 40.8 kHz, and the amplitude reached 12.4 µm, which effectively broke the limitation of cutting speed in UEVC. Finally, the UEVC device's performance was tested, and the advantages in improving the tungsten alloy surface quality and reducing diamond cutting tool wear validated the technical capability and principle of the proposed device.

Sign in / Sign up

Export Citation Format

Share Document