Thermoprobe method of measuring the temperature of molten metal and the difference between metal temperature and crystallization point

1966 ◽  
Vol 11 (5) ◽  
pp. 344-346
Author(s):  
L. A. Sokolov ◽  
G. S. Sel'kin
2008 ◽  
Vol 141-143 ◽  
pp. 191-194 ◽  
Author(s):  
Jin Kyu Lee ◽  
Shae K. Kim ◽  
Young Chul Lee

Novel hot chamber rheo-diecasting process has been successfully developed. It requires no additional processing equipment except commonly used hot chamber diecasting machine, no molten metal control like grain refinement procedure and no additional cycling time to produce slurry-on-demand. Additionally, it could lower molten metal temperature in a furnace. Process concept of novel hot chamber rheo-diecasting is simply based on the paradigm shift from HOW to WHERE for producing slurry-on-demand. This paper will demonstrate the possibility to achieve slurry-on-demand by novel hot chamber rheo-diecasting and the advantages for 3Cs applications.


1999 ◽  
Author(s):  
Y.B. Bragina ◽  
I. V. Bragin ◽  
V.P. Sgibnev ◽  
S.I. Bragin ◽  
I.A. Zheltikov ◽  
...  

2018 ◽  
Vol 925 ◽  
pp. 491-498
Author(s):  
Ryosuke Tasaki ◽  
Hideto Seno ◽  
Kunihiro Hashimoto ◽  
Kazuhiko Terashima

The sand mold press casting method is a novel iron casting process, which has developed by our group in recent years. The proposed method can cast iron into complex shapes with a high yield over 90% and produces high-quality products by filling control of molten metal during pressing motion. However, molten metal inside mold is cooled down by heat transfer to the molds and atmosphere, and often causes solidification before the end of press. Then, the pressing movement of the upper mold is blocked by the solidified metal. Therefore, to avoid the solidification during pressing sand mold, metal temperature must be heated properly to estimate the filling temperature decrease behavior based on analysis results of CFD simulator, FLOW-3D. The necessary condition not to solidify molten metal before the end of press has been found. It was made clear that the mold must be heated up to the necessary temperature beforehand in the pressing process. Furthermore, optimum velocity reference with specified pressure constraints has been designed to prevent casting defect such as penetration and also to minimize the temperature decrease. In this paper, optimum velocity control of servo cylinder considering the both of allowable pressure of molten metal and starting time of solidification is proposed by using a theoretical approach of Model Predictive Control: MPC method. The effectiveness of the proposed control system has been demonstrated by computer simulation and experiments using a laboratory scale machine with molten metal of casting iron.


2019 ◽  
Vol 13 (3) ◽  
pp. 611-617
Author(s):  
Toru Maruyama ◽  
Mitsuyoshi Tamaki ◽  
Gou Nakamura ◽  
Keisuke Nakamura

1990 ◽  
Vol 33 (6) ◽  
pp. 589-591
Author(s):  
I. E. Dobrovinskii ◽  
N. M. Kutergina ◽  
I. P. Kuritnyk ◽  
R. A. Sasinova

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
A. Hashoosh ◽  
H. Hirshy ◽  
E. B. Brousseau ◽  
A. Moosa

The reported study aims to demonstrate the application of a simple technique, which is referred to as pressure differential injection, to prepare metallic nanowires. This technique relies on the difference in pressure between the inside of sealed nanochannels of an anodic aluminium oxide (AAO) substrate and the ambient atmosphere to inject a molten metal, which is previously deposited on the substrate, into the AAO pores. The application of this technique enabled the fabrication of nanowires in aluminium with diameters comprised between 55 nm and 65 nm.


Author(s):  
Zafar Ullah Koreshi

The flow of a molten metal coolant, incorporating viscosity and a magnetic force in a channel typical of a nuclear fusion reactor is formulated. This is based on the flow conservation equations (continuity and momentum), along with Maxwell’s equations and Ohm’s law. These equations are solved with assumptions of steady fully-developed flow for Newtonian fluids. Exact solutions are compared with a Direct Numerical Simulation (DNS) to compute important engineering design parameters such as velocity distribution and pressure drop in a coolant channel. The analysis can be used for several candidate coolants including, molten lithium, sodium, lead, and compounds. The difference in velocity profile, and hence pressure drop, is strongly dependent on the magnetic field. In fact, it is shown that a flat (almost-turbulent) profile is obtained for the flow.


1962 ◽  
Vol 14 ◽  
pp. 149-155 ◽  
Author(s):  
E. L. Ruskol

The difference between average densities of the Moon and Earth was interpreted in the preceding report by Professor H. Urey as indicating a difference in their chemical composition. Therefore, Urey assumes the Moon's formation to have taken place far away from the Earth, under conditions differing substantially from the conditions of Earth's formation. In such a case, the Earth should have captured the Moon. As is admitted by Professor Urey himself, such a capture is a very improbable event. In addition, an assumption that the “lunar” dimensions were representative of protoplanetary bodies in the entire solar system encounters great difficulties.


1997 ◽  
Vol 161 ◽  
pp. 491-504 ◽  
Author(s):  
Frances Westall

AbstractThe oldest cell-like structures on Earth are preserved in silicified lagoonal, shallow sea or hydrothermal sediments, such as some Archean formations in Western Australia and South Africa. Previous studies concentrated on the search for organic fossils in Archean rocks. Observations of silicified bacteria (as silica minerals) are scarce for both the Precambrian and the Phanerozoic, but reports of mineral bacteria finds, in general, are increasing. The problems associated with the identification of authentic fossil bacteria and, if possible, closer identification of bacteria type can, in part, be overcome by experimental fossilisation studies. These have shown that not all bacteria fossilise in the same way and, indeed, some seem to be very resistent to fossilisation. This paper deals with a transmission electron microscope investigation of the silicification of four species of bacteria commonly found in the environment. The Gram positiveBacillus laterosporusand its spore produced a robust, durable crust upon silicification, whereas the Gram negativePseudomonas fluorescens, Ps. vesicularis, andPs. acidovoranspresented delicately preserved walls. The greater amount of peptidoglycan, containing abundant metal cation binding sites, in the cell wall of the Gram positive bacterium, probably accounts for the difference in the mode of fossilisation. The Gram positive bacteria are, therefore, probably most likely to be preserved in the terrestrial and extraterrestrial rock record.


Sign in / Sign up

Export Citation Format

Share Document