scholarly journals Preparation of activated carbon from banana peel waste for reducing air pollutant from motorcycle muffler

2018 ◽  
Vol 154 ◽  
pp. 01021 ◽  
Author(s):  
Achmad Chafidz ◽  
Widi Astuti ◽  
Dhoni Hartanto ◽  
Aulia Septiani Mutia ◽  
Purtiah Rantau Sari
Keyword(s):  
Activated Carbon ◽  
Motor Vehicle ◽  
Agricultural Waste ◽  
Chemical Activation ◽  
Economic Value ◽  
Air Pollutant ◽  
Banana Peel ◽  
Physical Activation ◽  
Exhaust Gas ◽  
Ft Ir

The exhaust gas or emission from motor vehicle contains various pollutants and some of them are toxic and very harmful for human health. In the present work, we prepared an activated carbon to reduce the toxic pollutants (via adsorption process) from the exhaust gas of the motor vehicle (particularly motorcycle in this work). The activated carbon was prepared from local banana peel which considered as an agricultural waste without economic value. To prepare the activated carbon, banana peel was carbonized using furnace at 500°C. Then the resulted carbon was activated using chemical activation with ZnCl2 and physical activation with either microwave (300 W) or furnace (700°C). The prepared activated carbon was then characterized using Scanning Electron Microscope (SEM) and Fourier Transform Infrared (FT-IR) analysis. The SEM result showed that the pore of microwave induced ZnCl2 activated carbon (ACM) was larger than the pore of virgin char/carbon and furnace induced ZnCl2 activataed carbon (ACF). The FT-IR spectrum of ACM showed some peaks at 3408.59 cm-1, 1589.25 cm-1, and 1093.63 cm-1. They are assigned to O-H stretching, C=O stretching, and C-OH stretching. Additionally, the adsorption performance of the prepared activation carbon to reduce the pollutants concentration (i.e. CO and CH) from the exhaust gas of motor vehicle was investigated. The results showed that the activated carbon induced by microwave and ZnCl2 activation (ACM) gave the best result. The adsorption or removal efficiency of gas CO reached approximately 97.64 %vol.

scholarly journals Preparation of Activated Carbon from Banana Peel Waste as Adsorbent for Motor Vehicle Exhaust Emissions

2018 ◽  
Vol 67 ◽  
pp. 03020 ◽  
Author(s):  
Yuliusman ◽  
Jervis Sinto ◽  
Yugo Widhi Nugroho ◽  
Hizba Ilmi Naf’an
Keyword(s):  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Motor Vehicle ◽  
Agricultural Waste ◽  
Chemical Activation ◽  
High Surface ◽  
Exhaust Emissions ◽  
Banana Peel ◽  
Vehicle Exhaust

Air pollution caused by motor vehicle exhaust emissions in the form of harmful gases becomes a problem for the health of living things in the surrounding environment. The alternative way to reduce those emissions is by utilizing agricultural waste as activated carbon (AC). AC can adsorbs those emissions due to its porous and high surface area. AC was made of banana peel waste that contains of lignocellulose and has considerable amount because of banana processing industrialization. AC was made through dehydration, carbonization at 350°C furnace without or with N2 gases of 0.15 NL/minute for 1 hour, then chemical activation using various concentrations of H2SO4 solution at 85°C for 1 hour. Characterization of activated carbon was done by iodine number test. The result shows that carbon chemical activation by 6 N of H2SO4 gave better result of iodine number than the lower concentration, obtaining 428 mg/g and overall yield of 41.68%. The result was even better on physical-and-chemical activation with same concentration of H2SO4, obtaining 617 mg/g with surface area of 614 m2/g and overall yield of 56.40%.

Adsorption of Methylene Blue and Reactive Black 5 by Activated Carbon Derived from Tamarind Seeds

2021 ◽  
Vol 2 (1) ◽  
pp. 1-12
Author(s):  
Zaniah Ishak ◽  
Sa’diah Salim ◽  
Dilip Kumar
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Agricultural Waste ◽  
Chemical Activation ◽  
Industrial Sector ◽  
Physical Activation ◽  
Reactive Black 5 ◽  
Synthetic Dyes ◽  
Tamarind Seed ◽  
Pseudo Second Order

One of the most environmentally friendly methods to treat wastewater, especially synthetic dyes, is the production of activated carbon from agricultural waste. Tamarind seeds were transformed from negative-value waste into activated carbon in order to study the removal of synthetic dyes. The particular agro waste was soaked in ZnCl2 for chemical activation to increase its surface area and enhance its porosity. Physical activation of tamarind seeds was done by the carbonization process by burning at a temperature of 300 °C for 1 hour and cooling for 24 hours before washing with HCL to activate a pore surface for the tamarind seeds' carbon. The effects of parameters related to the adsorption of the dyes by tamarind seed activated carbon, such as contact time, initial concentration, absorbance dosage, and pH, were studied. The experimental data found that adsorption on both synthetic dyes exhibited a Langmuir isotherm in which the correlation value, R2, was 0.9227 (methylene blue) and 0.6117 (Reactive black 5). Meanwhile, the rate of adsorption for methylene blue (MB) and Reactive black 5 (RB5) by tamarind seed activated carbon was found to be well fitted in a pseudo-second-order model. More research is needed to meet the standard effluent of dyeing wastewater from the industrial sector.

scholarly journals Production of Activated Carbon from Carbonaceous Agricultural Waste Material: Coconut Fibres

2021 ◽  
Vol 40 (1) ◽  
pp. 19-24
Author(s):  
E.O. Ohimor ◽  
D.O. Temisa ◽  
P.I. Ononiwu
Keyword(s):  
Activated Carbon ◽  
Cocos Nucifera ◽  
Agricultural Waste ◽  
Chemical Activation ◽  
Activated Carbon Adsorption ◽  
Carbon Adsorption ◽  
Infrared Reflection ◽  
Morphological Composition ◽  
Ft Ir ◽  
Coconut Fibers

Activated carbon was produced from Cocos nucifera (coconut) fibers by carbonization and activation processes. The sample was first pretreated before carbonization and activation processes at 450°C and 700°C respectively in an electric furnace. Chemical activation using Potassium hydroxide (KOH) 4:1 (weight basis) was carried out to increase the activated carbon adsorption properties. The element contained in the sample was analyzed using the Energy Dispersive Spectroscopy (EDS) while the surface morphological composition was determined by Scanning Electron Microscope (SEM) and the chemical bonds present in the sample was characterized using Fourier transform infrared reflection (FT-IR). From the research carried out, the results show that activated carbon produced from coconut fibers would be useful and effective for adsorbent purposes, considering its large pores.

scholarly journals Laboratory solid waste from practical activity as activated carbon precursor for reducing methylene blue in the laboratory wastewater

2021 ◽  
Vol 3 (2) ◽  
pp. 73-79
Author(s):  
Aninda Tifani Puari
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Solid Waste ◽  
Potassium Hydroxide ◽  
Agricultural Waste ◽  
Chemical Activation ◽  
Sem Analysis ◽  
Koh Activation ◽  
Ft Ir ◽  
Basic Biology

Activated carbon (AC) from agricultural waste has become one promising way to produce AC regarding to low price of the precursor and its effect to environment. In this research, the solid waste from the basic biology practical in UPT. Basic and Central Laboratory, Andalas University (Unand) was utilized as the precursor for producing low price AC. The activation was done by chemical activation using three different activating agents which were zink chloride (ZnCl2), phosphoric acid (H3PO4), potassium hydroxide (KOH). The carbonization process was done at temperature of 700°C. The precursor and three different AC after activation were characterized using fourier-transform infrared spectroscopy (FT-IR) to examine  the functional group and scanning electron microscope (SEM) to observe the pores structure. The adsorption efficiency (AE) of each AC on methylene blue (MB) contained in laboratory wastewater was examined through adsorption process with retention time of 30 minutes at room temperature and neutral pH. SEM analysis showed that the three activating agents were resulting in higher surface area and more pores were formed. The highest AE of MB from laboratory wastewater for each AC were 97,5 %, 96,31%, and 90,79 for KOH, , ZnCl2, and H3PO4, respectively. Meanwhile, the highest adsorption capacity was achieved by AC through KOH activation with 0,003 mg/g

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

scholarly journals Decoration of Zinc Oxide Nanorods into the Surface of Activated Carbon Obtained from Agricultural Waste for Effective Removal of Methylene Blue Dye

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5667
Author(s):  
Priyanka Shrestha ◽  
Manoj Kumar Jha ◽  
Jeevan Ghimire ◽  
Agni Raj Koirala ◽  
Rajeshwar Man Shrestha ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Zinc Oxide ◽  
Activated Carbon ◽  
Agricultural Waste ◽  
Chemical Activation ◽  
Zno Nanorods ◽  
Waste Product ◽  
Hydrothermal Process ◽  
Photocatalytic Property ◽  
Zinc Oxide Nanorods

Zinc oxide (ZnO) nanorods incorporated activated carbon (AC) composite photocatalyst was synthesized using a hydrothermal process. The AC was prepared from lapsi (Choerospondias axillaris) seed stone, an agricultural waste product, found in Nepal by the chemical activation method. An aqueous suspension of AC with ZnO precursor was subjected to the hydrothermal treatment at 140 °C for 2 h to decorate ZnO rods into the surface of AC. As-obtained ZnO nanorods decorated activated carbon (ZnO/AC) photocatalyst was characterized by various techniques, such as scanning electron microscopy (SEM), X-ray diffraction (XRD), and photoluminescence (PL) spectroscopy. Results showed that highly crystalline hexagonal ZnO nanorods were effectively grown on the surface of porous AC. The photocatalytic property of the as-prepared ZnO/AC composite was studied by degrading methylene blue (MB) dye under UV-light irradiation. The ZnO/AC composite showed better photocatalytic property than that of the pristine ZnO nanorods. The enhanced photocatalytic performance in the case of the ZnO/AC composite is attributed to the combined effects of ZnO nanorods and AC.

scholarly journals Preparation and Characterization of Activated Carbon from Waste Rubber Tires: A Comparison between Physical and Chemical Activation

2015 ◽  
Vol 1107 ◽  
pp. 347-352 ◽  
Author(s):  
Collin Glen Joseph ◽  
Duduku Krishniah ◽  
Yun Hin Taufiq-Yap ◽  
Masnah Massuanna ◽  
Jessica William
Keyword(s):  
Activated Carbon ◽  
Automobile Industry ◽  
Chemical Activation ◽  
Waste Product ◽  
Physical Activation ◽  
Activation Process ◽  
Waste Rubber ◽  
Percentage Yield ◽  
Static Conditions ◽  
Physical And Chemical

Abstract. Waste tires, which are an abundant waste product of the automobile industry, were used to prepare activated carbon by means of physical and chemical activation. A two-stage process was used, with a semi-carbonization stage as the first stage, followed by an activation stage as the second stage.All experiments were conducted in a laboratory-scale muffle furnace under static conditions in a self-generated atmosphere. During this process, the effects of the parametric variables of semi-carbonization time (for the physical activation process), activation time and temperature and impregnation ratios (for the chemical activation process) on the percentage yield were studied and compared. Varying these parametric variables yielded interesting results, which in turn affected the adsorption process of 2,4-DCP, which was the simulated pollutant in aqueous form. The optimized percentage yields of activated carbon that were obtained were 41.55% and 44.88% ofthe physical and chemical activation treatment processes respectively.Keywords: Physical activation, chemical activation, waste rubber tires, 2,4-dichlorophenol, activated carbon.

AKTIVASI KIMIA-FISIK LIMBAH SERUTAN ROTAN MENJADI KARBON AKTIF

2014 ◽  
Vol 14 (1) ◽  
pp. 82-98
Author(s):  
Andy Mizwar
Keyword(s):  
Activated Carbon ◽  
Water Content ◽  
Iodine Number ◽  
Surface Area ◽  
Chemical Activation ◽  
Raw Material ◽  
Physical Activation ◽  
Fixed Carbon ◽  
Impregnation Time ◽  
Physical And Chemical

Limbah rotan dari industri kerajinan dan mebel berpotensi untuk dijadikan sebagai bahan baku pembuatan karbon aktif karena memiliki kandungan holoselulosa dan kadar karbon yang tinggi. Penelitian ini bertujuan untuk menganalisis efektifitas dari aktivasi kimia menggunakan larutan natrium klorida (NaCl) yang dilanjutkan dengan aktivasi fisik dalam pembuatan karbon aktif berbahan dasar  limbah serutan rotan. Pembuatan karbon aktif diawali dengan proses karbonisasi pada suhu 250°C selama 1 jam. Selanjutnya aktivasi kimia menggunakan larutan NaCl dengan variasi konsentrasi 10%, 15% dan 20% serta waktu perendaman selama 10, 15 dan 20 jam. Aktivasi fisik dilakukan dengan pembakaran pada suhu 700°C selama 30 menit. Analisis karakteristik fisik-kimia karbon aktif mengacu pada SNI 06-3730-95, meliputi kadar air, fixed carbon, dan iodine number, sedangkan perhitungan luas permukaan spesifik karbon aktif dilakukan dengan Metode Sears. Hasil penelitian ini menunjukkan bahwa kondisi optimum aktivasi kimia terjadi pada konsentrasi NaCl 10% dan lama perendaman 10 jam dengan hasil analisis kadar air 2.90%, fixed carbon 72.70%, iodine number 994.59 mg/g dan luas permukaan 1587.67 m²/g. Peningkatan fixed carbon, iodine number dan luas permukaan karbon aktif berbanding terbalik dengan peningkatan konsentrasi NaCl dan lama waktu perendaman, sedangkan peningkatan kadar air pada karbon aktif berlaku sebaliknya. Rattan waste from handicraft and furniture industry could potentially be used as raw material of activated carbon due to high content of holoselulosa and carbon. This paper investigates the effectiveness of chemical activation using sodium chloride (NaCl) followed by physical activation in the making of activated carbon-based on rattan shavings waste. Preparation of the activated carbon began with the carbonization process at 250°C for 1 hour. Furthermore chemical activation using a variation of NaCl concentrations 10%, 15% and 20% as well as the time of immersion 10, 15 and 20 hours. Physical activation was done by burning at 700°C for 30 minutes. Analysis of the physical and chemical characteristics of the activated carbon was referred to the SNI 06-3730-95, including of moisture content, fixed carbon and iodine number, while the calculation of the specific surface area was done by the Sears’s method. The results of this study showed that the optimum conditions of chemical activation occurred in impregnation by NaCl 10% for 10 hours. The water content, fixed carbon, iodine number and surface area of activated carbon was 2.90%, 72.70%, 994.59 mg/g and 1587.67 m²/g  respectively. The increase values of fixed carbon, iodine number, and surface area was inversely proportional to the increase of NaCl concentration and the length of impregnation time, while the increase of water content applied vice versa.

Preparation of Activated Carbon Monolith Electrodes from Sugarcane Bagasse by Physical and Physical-Chemical Activation Process for Supercapacitor Application

2014 ◽  
Vol 896 ◽  
pp. 179-182 ◽  
Author(s):  
Erman Taer ◽  
Iwantono ◽  
Saidul Tua Manik ◽  
R. Taslim ◽  
D. Dahlan ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Sugarcane Bagasse ◽  
Chemical Activation ◽  
Physical Activation ◽  
Activation Process ◽  
X Ray Diffraction ◽  
Supercapacitor Application ◽  
Carbon Monolith ◽  
Physical Chemical ◽  
Activated Carbon Monoliths

Binderless activated carbon monoliths (ACMs) for supercapacitor electrodes were prepared from sugarcane bagasse by two different methods of physical and combination of physical-chemical activation process. The CO2 gas was used as physical activation agent and 0.3 M KOH was chosen as chemical activation agent. The ACMs were tested as electrodes in two-electrode systems of the coin tape cell supercapacitor that consists of stainless steel as current collectors and 1 M H2SO4 as an electrolyte. The improving of resistive, capacitive and energy properties of combination of physical-chemical ACMs electrodes were shown by an impedance spectroscopy, a cyclic voltammetry and a galvanostatic charge-discharge method. The improving of resistive, capacitive and energy properties as high as 1 to 0.6 Ω, 146 to 178 F g-1, 3.83 to 4.72 W h kg-1, respectively. The X-ray diffraction analysis and field emission scanning electron microscope were performed to characterize the crystallite and morphology characteristics. The results showed that the combination of physical-chemical activation process have given a good improving in performance of the bagasse based ACMs electrodes in supercapacitor application.

Sign in / Sign up

Export Citation Format

Share Document