Vibration and critical characteristics of the tilting pads journal bearing-rotor system

2019 ◽  
Vol 71 (2) ◽  
pp. 295-300 ◽  
Author(s):  
Zhiming Zhao ◽  
Feng Ji ◽  
Yongsheng Guan ◽  
Xiaoyang Yuan
Keyword(s):  
Theoretical Calculation ◽  
System Design ◽  
Critical Speed ◽  
Journal Bearing ◽  
Large Diameter ◽  
Vibration Monitoring ◽  
Content Type ◽  
Vibration Data ◽  
Rotor Bearing ◽  
Bearing System

Purpose High power rotating machinery requires large diameter bearings that can perform under extreme conditions. Vibrations and critical speeds of rotor supported by tilting pad journal bearing (TPJBs) exceeding their design limits may cause unit failure. This paper aims to investigate the experimental technique for large diameter bearings. Design/methodology/approach To obtain the experimental support for rotor-bearing system design, an experiment focusing on vibration monitoring is given. The sensors arrangement, monitoring system and critical speed identification method are provided. Findings By using test bench in factory unit, a large amount of vibrations data of different working situations is obtained. In addition, a method named non-excitation identification for critical speed is proposed. The critical speed of rotor identified through vibration data is given. The theoretical calculation results are also presented. Originality/value The basis for rotor-bearing system design can be obtained through comparisons between the experimental results and the theoretical calculation data.

Theoretical and experimental dynamics analysis of rotor-bearing system supported by elliptical bearings

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Zhiming Zhao ◽  
Rui Zhang ◽  
Feng Ji ◽  
Xiaoyang Yuan
Keyword(s):  
Peer Review ◽  
Dynamic Characteristics ◽  
Critical Speed ◽  
Design Method ◽  
Large Diameter ◽  
Rotor System ◽  
Content Type ◽  
Vibration Data ◽  
Rotor Bearing ◽  
Bearing System

Purpose High power and speed are new demands for rotating machinery which needs the journal bearings with high dynamic characteristics. The critical speed of the rotor-bearing system is one of the most significant parameters to evaluate the dynamic characteristics. This paper aims to investigate the theoretical and experimental analysis of a rotor system supported by large diameter elliptical bearings. Design/methodology/approach To obtain the theoretical and experimental support for rotor-bearing system design, dynamic characteristics theoretical analysis based on the finite difference method is given and an experiment focuses on critical speed identification is carried out. Findings The theoretical calculation results indicate that the critical speed is near to 800 rpm and there is no large vibration amplitude round working speed (1,500 rpm). Using the test bench in the factory unit, vibration data including three experimental processes are obtained. According to the vibration data, the critical speed is identified which also indicates that it is stable when working at 1,500 rpm. Originality/value The design method for the rotor system supported by large diameter elliptical bearing can be obtained by the theoretical and experimental results shown in this paper. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2020-0122/

Experimental dynamic analysis of rod-fastening rotor bearing system with a transverse crack

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Nanshan Wang ◽  
Heng Liu ◽  
Qidan Wang ◽  
Shemiao Qi ◽  
Yi Liu
Keyword(s):  
Peer Review ◽  
Dynamic Characteristics ◽  
Vibration Amplitude ◽  
Critical Speed ◽  
Transverse Crack ◽  
Content Type ◽  
Rotor Bearing ◽  
Speed Up ◽  
Rod Fastening Rotor ◽  
Bearing System

Purpose This study aims to obtain the dynamic behaviours of cracked rod-fastening rotor bearing system (RFBS), and experimental investigation was carried out to examine the dynamic characteristics of this kind of assembled rotor bearing system with a transverse crack passing through the critical speed. Design/methodology/approach An experimental test rig of cracked RFBS was established for examining the vibration behaviours between intact and cracked system. The crack on the surface of a fastening rod was simulated by wire-electrode cutting processing method. The comprehensive analysis method of vibration was used to obtain the dynamic characteristics such as vibration amplitude, acceleration and whirling orbits before and after the critical speed as well as the instantaneous response in the process of speed up. Findings Some experimental vibration datum is obtained for cracked RFBS. The appearance of a crack will introduce the initial bending and make the vibration amplitude, acceleration and instant response in the process of speed up increase greatly as well as the change of whirling orbits. Originality/value The actual vibration characteristics for this complex assembled rotor system with a transverse crack are given passing through the critical speed. It can provide some useful help for monitoring the vibration behaviours of this kind of assembled rotor system as well as the detection of the crack fault. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2020-0260/

Nonlinear Dynamics of Flexible Rotors Supported on Journal Bearings—Part I: Analytical Bearing Model

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Mohammad Miraskari ◽  
Farzad Hemmati ◽  
Mohamed S. Gadala
Keyword(s):  
Journal Bearing ◽  
Nonlinear Coefficient ◽  
Journal Bearings ◽  
Flexible Rotor ◽  
Dynamic Coefficients ◽  
Flexible Rotors ◽  
Rotor Bearing ◽  
Bearing Force ◽  
Derivatives Of ◽  
Bearing System

To determine the bifurcation types in a rotor-bearing system, it is required to find higher order derivatives of the bearing forces with respect to journal velocity and position. As closed-form expressions for journal bearing force are not generally available, Hopf bifurcation studies of rotor-bearing systems have been limited to simple geometries and cavitation models. To solve this problem, an alternative nonlinear coefficient-based method for representing the bearing force is presented in this study. A flexible rotor-bearing system is presented for which bearing force is modeled with linear and nonlinear dynamic coefficients. The proposed nonlinear coefficient-based model was found to be successful in predicting the bifurcation types of the system as well as predicting the system dynamics and trajectories at spin speeds below and above the threshold speed of instability.

Non-linear stability analysis of micropolar fluid lubricated journal bearings with turbulent effect

2019 ◽  
Vol 71 (1) ◽  
pp. 31-39
Author(s):  
Subrata Das ◽  
Sisir Kumar Guha
Keyword(s):  
Stability Analysis ◽  
Linear Stability ◽  
Micropolar Fluid ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Turbulent Regime ◽  
Content Type ◽  
Non Linear ◽  
The Stability ◽  
Bearing System

Purpose The purpose of this paper is to investigate the effect of turbulence on the stability characteristics of finite hydrodynamic journal bearing lubricated with micropolar fluid. Design/methodology/approach The non-dimensional transient Reynolds equation has been solved to obtain the non-dimensional pressure field which in turn used to obtain the load carrying capacity of the bearing. The second-order equations of motion applicable for journal bearing system have been solved using fourth-order Runge–Kutta method to obtain the stability characteristics. Findings It has been observed that turbulence has adverse effect on stability and the whirl ratio at laminar flow condition has the lowest value. Practical implications The paper provides the stability characteristics of the finite journal bearing lubricated with micropolar fluid operating in turbulent regime which is very common in practical applications. Originality/value Non-linear stability analysis of micropolar fluid lubricated journal bearing operating in turbulent regime has not been reported in literatures so far. This paper is an effort to address the problem of non-linear stability of journal bearings under micropolar lubrication with turbulent effect. The results obtained provide useful information for designing the journal bearing system for high speed applications.

Dynamic analysis of a helical geared rotor-bearing system with composite rotating shafts

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ying-Chung Chen ◽  
Xu Feng Cheng ◽  
Siu-Tong Choi
Keyword(s):  
Composite Material ◽  
Dynamic Analysis ◽  
Dynamic Characteristics ◽  
Mesh Stiffness ◽  
Content Type ◽  
Gear Mesh ◽  
Rotor Bearing ◽  
Rotating Shafts ◽  
Gear Mesh Stiffness ◽  
Bearing System

Purpose This study aims to study the dynamic characteristics of a helical geared rotor-bearing system with composite material rotating shafts. Design/methodology/approach A finite element model of a helical geared rotor-bearing system with composite material rotating shafts is developed, in which the rotating shafts of the system are composed of composite material and modeled as Timoshenko beam; a rigid mass is used to represent the gear and their gyroscopic effect is taken into account; bearings are modeled as linear spring-damper; and the equations of motion are obtained by applying Lagrange’s equation. Natural frequencies, mode description, lateral responses, axial responses, lamination angles, lamination numbers, gear mesh stiffness and bearing damping coefficients are investigated. Findings The desired mechanical properties could be constructed using different lamination numbers and fiber included angles by composite rotating shafts. The frequency of the lateral module decreases as the included angle of the fibers and the principal shaft of the composite material rotating shaft increase. Because of the gear mesh stiffness increase, the resonance frequency of the coupling module of the system decreases, the lateral module is not influenced and the steady-state response decreases. The amplitude of the steady-state lateral and axial responses gradually decreases as the bearing damping coefficient increases. Practical implications The model of a helical geared rotor-bearing system with composite material rotating shafts is established in this paper. The dynamic characteristics of a helical geared rotor-bearing system with composite rotating shafts are investigated. The numerical results of this study can be used as a reference for subsequent personnel research. Originality/value The dynamic characteristics of the geared rotor-bearing system had been reported in some literature. However, the dynamic analysis of a helical geared rotor-bearing system with composite material rotating shafts is still rarely investigated. This paper shows some novel results of lateral and axial response results obtained by different lamination angles and different lamination numbers. In the future, it makes valuable contributions for further development of dynamic analysis of a helical geared rotor-bearing system with composite material rotating shafts.

scholarly journals Dynamic Characteristics and Experimental Research of a Two-Span Rotor-Bearing System with Rub-Impact Fault

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Rui Zhu ◽  
Guang-chao Wang ◽  
Qing-peng Han ◽  
An-lei Zhao ◽  
Jian-xing Ren ◽  
...  
Keyword(s):  
Dynamic Characteristics ◽  
Critical Speed ◽  
Great Influence ◽  
Experimental Platform ◽  
Rotating Machine ◽  
Rotor Bearing ◽  
Before And After ◽  
Analysis System ◽  
The Stability ◽  
Bearing System

Rotor rub-impact has a great influence on the stability and safety of a rotating machine. This study develops a dynamic model of a two-span rotor-bearing system with rubbing faults, and numerical simulation is carried out. Moreover, frictional screws are used to simulate a rubbing state by establishing a set of experimental devices that can simulate rotor-stator friction in the rotor system. Through the experimental platform and its analysis system, the rubbing experiment was conducted, and the vibration of the rotor-bearing system before and after the critical speed is observed. Rotors running under normal condition, local slight rubbing, and severe rubbing throughout the entire cycle are simulated. Dynamic trajectories, frequency spectrum diagrams, chart of axis track, and Poincare maps are used to analyze the features of the rotor-bearing system with rub-impact faults under various parameters. The vibration characteristics of rub impact are obtained. Results show that the dynamic characteristics of the rotor-bearing system are affected by the change in velocity and degree of impact friction. The findings are helpful in further understanding the dynamic characteristics of the rub-impact fault of the two-span rotor-bearing system and provide reference for fault diagnosis.

Nonlinear Vibration Prediction of a Highly Flexible Rotor Supported by an Axial Groove Journal Bearing Considering Journal Angular Whirling Motion

2019 ◽  
Author(s):  
Nuntaphong Koondilogpiboon ◽  
Tsuyoshi Inoue
Keyword(s):  
Nonlinear Vibration ◽  
Ball Bearing ◽  
Journal Bearing ◽  
Flexible Rotor ◽  
Large Disk ◽  
Subcritical Bifurcation ◽  
Whirling Motion ◽  
Vibration Prediction ◽  
Rotor Bearing ◽  
Bearing System

Abstract In this study, the difference in dynamic behavior of the rotor-bearing system supported by the bearing model that considers both lateral and angular whirling motions of the journal (model A), and the model that considers only lateral whirling motion (model B) is investigated. The rotor model consists of a slender shaft, a large disk and two small disks supported by a self-aligning ball bearing and an axial groove journal bearing of L/D = 0.6. Three positions of the large disk: 410, 560, and 650 mm measured from the ball bearing, are investigated. Numerical integration of the rotor-bearing system which is modally reduced to the 1st forward mode is performed at above the onset speed of instability until either a steady state journal orbit or contact between the journal and the bearing occurs to identify the bifurcation type. Numerical results using model A indicate subcritical bifurcation with the contact between the journal and the inboard side of the bearing in all three large disk positions, whereas those of model B indicate subcritical bifurcation when the large disk position is at 410 mm, and supercritical bifurcation is observed in the other two cases. Lastly, the experiments at the same three large disk positions are performed. Subcritical bifurcation with the contact between the journal and the inboard side of the bearing is observed in all large disk positions, which conforms with the calculation result of model A. As a result, model A is essential in nonlinear vibration analysis of a highly flexible rotor system.

Behaviour of two-lobe hole-entry hybrid journal bearing system under the combined influence of textured surface and micropolar lubricant

2017 ◽  
Vol 69 (6) ◽  
pp. 844-862 ◽  
Author(s):  
Chandra B. Khatri ◽  
Satish C. Sharma
Keyword(s):  
Design Methodology ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Numerical Technique ◽  
Surface Texturing ◽  
Textured Surface ◽  
Performance Parameters ◽  
Content Type ◽  
Fluid Theory ◽  
Bearing System

Purpose The aim of the present paper is to study the combined influence of textured surface and micropolar lubricant behaviour on the performance of two-lobe hole-entry hybrid journal bearing system. The bearing performance parameters of the textured circular/two-lobe hole-entry hybrid journal bearing system have been computed against the constant vertical external load supported by the bearing. Design/methodology/approach In this work, Eringen’s micropolar fluid theory has been used to derive the governing Reynolds equation. The consequent solution of the governing Reynolds equation has been obtained by using finite element method (FEM) numerical technique. Findings The present study indicates that the use of the textured surface, two-lobe profile of bearing and micropolar lubricant, significantly enhances the bearing performance as compared to non-textured circular journal bearing. Originality/value The present study concerning the influence of surface texturing on the behaviour of the two-lobe hole-entry hybrid journal bearing lubricated with micropolar lubricant is original. The theoretically simulated results of the present study will be useful to design an efficient journal bearing system.

scholarly journals Nonlinear Dynamics Analysis of Tilting Pad Journal Bearing-Rotor System

2011 ◽  
Vol 18 (1-2) ◽  
pp. 45-52 ◽  
Author(s):  
Jiayang Ying ◽  
Yinghou Jiao ◽  
Zhaobo Chen
Keyword(s):  
Nonlinear Dynamics ◽  
System Dynamics ◽  
Journal Bearing ◽  
Rotor System ◽  
Moment Of Inertia ◽  
Dynamics Analysis ◽  
Tilting Pad ◽  
Rotor Bearing ◽  
Tilting Pad Journal Bearing ◽  
Bearing System

The nonlinear dynamics theory is increasingly applied in the dynamics analysis of tilting pad journal bearing-rotor system. However, extensive work on system dynamics done previously neglects the influence caused by the moment of inertia of the pad. In this paper, a comparison is made between the responses of the rotor in the bearings with and without pad inertia effect. Taking the Jeffcott rotor system as an example, the characteristics of bearing-rotor system, such as bifurcation diagram, cycle response, frequency spectrum, phase trajectories, and Poincaré maps, were attained within a certain rotation rate range. The pivotal oil-film force of tilting pad journal bearing was calculated by database method. The results directly demonstrate that considering the influence of the pad moment of inertia, system dynamics characteristics are found more complicated when rotor-bearing system works around natural frequency and system bifurcation is observed forward when rotor-bearing system works on high-speed range.

A method to obtain the linear dynamic coefficients for journal bearing in vertical rotors

2019 ◽  
Vol 72 (1) ◽  
pp. 38-45 ◽  
Author(s):  
Changmin Chen ◽  
Jianping Jing ◽  
Jiqing Cong
Keyword(s):  
Coordinate System ◽  
Linear Models ◽  
Journal Bearing ◽  
Leading Edge ◽  
Content Type ◽  
Linear Dynamic ◽  
Dynamic Coefficients ◽  
Vertical Rotor ◽  
Rotor Bearing ◽  
Stiffness And Damping

Purpose The infinitesimal perturbation (IP) method is commonly used in calculating stiffness and damping of journal bearing in horizon rotor systems. The boundary condition (BC) for the perturbed pressure is assumed being zero at leading edge of film, although it is usually not zero because of nonzero pressure gradient. This assumption is sufficiently accurate for most purpose in horizon rotors. However, for journal bearing in vertical rotor-bearing systems, the BC with the assumption in IP method will bring in significant errors in calculating linear dynamic coefficients. This paper aims to propose a method to obtain the dynamic coefficients of journal bearing in vertical rotors. Design/methodology/approach The stiffness and damping are approached based on IP method and the modified BC of perturbed pressure. As it is difficult to predict perturbed pressure at leading edge at a fixed coordinate system using IP method, a dynamic coordinate system is introduced in this method, of which the origin on circumferential direction is defined as the leading edge of film. Findings The effectiveness and accuracy of proposed IP method in dynamic coordinate (IPMDC) system are verified by comparing the obtained results with analytical solutions. The comparison shows that the results from IPMDC present a good agreement with the analytic solutions. Originality/value The proposed method can be applied in obtaining linear dynamic coefficients of journal bearing in vertical rotors with high precisions. Instead of the usual nonlinear analysis of vertical rotors, this method provides a feasibility of predicting the instability threshold of vertical rotor-bearing systems via linear models.

Sign in / Sign up

Export Citation Format

Share Document