Influence of Base Slant on the Wake Structure and Drag of Road Vehicles

1983 ◽  
Vol 105 (4) ◽  
pp. 429-434 ◽  
Author(s):  
S. R. Ahmed
Keyword(s):  
Experimental Data ◽  
Reynolds Number ◽  
Kinetic Energy ◽  
Aerodynamic Drag ◽  
Energy Content ◽  
Vortex Motion ◽  
Pressure Measurements ◽  
Road Vehicles ◽  
Wake Structure ◽  
Slant Angle

The time averaged wake structure of a realistically dimensioned quarter scale automobile model was studied in a wind tunnel on the basis of flow visualization, wake surveys, force and pressure measurements. Through a systematic variation of base slant angle in the range of 0 to 40 deg, the ensuing changes in the wake structure were observed and the wake structure present at lowest value of aerodynamic drag is shown. Experimental data were obtained at a model length based Reynolds number of 4.29 million. Correlation of wake structure with drag, pressure distribution, and kinetic energy content of vortex motion in wake is addressed.

Scaling of global properties of turbulence and skin friction in pipe and channel flows

2010 ◽  
Vol 652 ◽  
pp. 65-73 ◽  
Author(s):  
VICTOR YAKHOT ◽  
SEAN C. C. BAILEY ◽  
ALEXANDER J. SMITS
Keyword(s):  
Experimental Data ◽  
Reynolds Number ◽  
Kinetic Energy ◽  
Friction Factor ◽  
Turbulent Kinetic Energy ◽  
Dissipation Rate ◽  
Friction Velocity ◽  
Scaling Law ◽  
Global Properties ◽  
Reynolds Number Dependence

Experimental data on the Reynolds number dependence of the area-averaged turbulent kinetic energy K and dissipation rate ℰ are presented. It is shown that while in the interval ReD > 105 the total kinetic energy scales with friction velocity (K/u*2 = const), a new scaling law K/〈U〉2 ∝ K/(u*2ReDθ) = const (θ ≈ 1/4) has been discovered in the interval ReD < 105. It is argued that this transition is responsible for the well-known change in the scaling behaviour of the friction factor observed in pipe and channels flows at ReD ≈ 105.

scholarly journals Fibre-induced drag reduction

2008 ◽  
Vol 602 ◽  
pp. 209-218 ◽  
Author(s):  
J. J. J. GILLISSEN ◽  
B. J. BOERSMA ◽  
P. H. MORTENSEN ◽  
H. I. ANDERSSON
Keyword(s):  
Experimental Data ◽  
Numerical Simulation ◽  
Reynolds Number ◽  
Drag Reduction ◽  
Elastic Layer ◽  
Turbulent Drag Reduction ◽  
Rigid Polymer ◽  
Fibre Concentration ◽  
Induced Drag ◽  
Turbulent Drag

We use direct numerical simulation to study turbulent drag reduction by rigid polymer additives, referred to as fibres. The simulations agree with experimental data from the literature in terms of friction factor dependence on Reynolds number and fibre concentration. An expression for drag reduction is derived by adopting the concept of the elastic layer.

scholarly journals A study of computational methods for wake structure and base pressure prediction of a generic SUV model with fixed and rotating wheels

2017 ◽  
Vol 231 (9) ◽  
pp. 1222-1238 ◽  
Author(s):  
David Forbes ◽  
Gary Page ◽  
Martin Passmore ◽  
Adrian Gaylard
Keyword(s):  
Experimental Data ◽  
Computational Methods ◽  
Large Scale ◽  
Ground Plane ◽  
Computational Cost ◽  
Rear Wheel ◽  
Base Pressure ◽  
Detached Eddy Simulation ◽  
Wake Structure ◽  
Wake Interactions

This study is an evaluation of the computational methods in reproducing experimental data for a generic sports utility vehicle (SUV) geometry and an assessment on the influence of fixed and rotating wheels for this geometry. Initially, comparisons are made in the wake structure and base pressures between several CFD codes and experimental data. It was shown that steady-state RANS methods are unsuitable for this geometry due to a large scale unsteadiness in the wake caused by separation at the sharp trailing edge and rear wheel wake interactions. unsteady RANS (URANS) offered no improvements in wake prediction despite a significant increase in computational cost. The detached-eddy simulation (DES) and Lattice–Boltzmann methods showed the best agreement with the experimental results in both the wake structure and base pressure, with LBM running in approximately a fifth of the time for DES. The study then continues by analysing the influence of rotating wheels and a moving ground plane over a fixed wheel and ground plane arrangement. The introduction of wheel rotation and a moving ground was shown to increase the base pressure and reduce the drag acting on the vehicle when compared to the fixed case. However, when compared to the experimental standoff case, variations in drag and lift coefficients were minimal but misleading, as significant variations to the surface pressures were present.

Separation in oscillating laminar boundary-layer flows

1971 ◽  
Vol 47 (1) ◽  
pp. 21-31 ◽  
Author(s):  
R. A. Despard ◽  
J. A. Miller
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Experimental Investigation ◽  
Reynolds Number ◽  
Reverse Flow ◽  
Oscillation Amplitude ◽  
Hot Wire ◽  
Boundary Layer Flows ◽  
Laminar Boundary Layers ◽  
History Of

The results of an experimental investigation of separation in oscillating laminar boundary layers is reported. Instantaneous velocity profiles obtained with multiple hot-wire anemometer arrays reveal that the onset of wake formation is preceded by the initial vanishing of shear at the wall, or reverse flow, throughout the entire cycle of oscillation. Correlation of the experimental data indicates that the frequency, Reynolds number and dynamic history of the boundary layer are the dominant parameters and oscillation amplitude has a negligible effect on separation-point displacement.

Difference in Critical Reynolds Number Between Hagen-Poiseuille and Plane Poiseuille Flows

2001 ◽  
Author(s):  
Hidesada Kanda
Keyword(s):  
Experimental Data ◽  
Reynolds Number ◽  
Poiseuille Flow ◽  
Average Velocity ◽  
Critical Reynolds Number ◽  
Inlet Section ◽  
Parallel Plates ◽  
Plane Poiseuille Flow ◽  
Contraction Ratio ◽  
Significant Difference

Abstract For plane Poiseuille flow, results of previous investigations were studied, focusing on experimental data on the critical Reynolds number, the entrance length, and the transition length. Consequently, concerning the natural transition, it was confirmed from the experimental data that (i) the transition occurs in the entrance region, (ii) the critical Reynolds number increases as the contraction ratio in the inlet section increases, and (iii) the minimum critical Reynolds number is obtained when the contraction ratio is the smallest or one, and there is no-shaped entrance or straight parallel plates. Its value exists in the neighborhood of 1300, based on the channel height and the average velocity. Although, for Hagen-Poiseuille flow, the minimum critical Reynolds number is approximately 2000, based on the pipe diameter and the average velocity, there seems to be no significant difference in the transition from laminar to turbulent flow between Hagen-Poiseuille flow and plane Poiseuille flow.

Velocity and Pressure Measurements Along a Row of Confined Cylinders

2006 ◽  
Author(s):  
Barton L. Smith ◽  
Jack J. Stepan ◽  
Donald M. McEligot
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Symmetry Plane ◽  
Field Measurements ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Recirculation Region ◽  
Pressure Measurements ◽  
Layer Transition ◽  
Flow Experiments

The results of flow experiments performed in a cylinder array designed to mimic a VHTR Nuclear Plant lower plenum design are presented. Pressure drop and velocity field measurements were made. Based on these measurements, five regimes of behavior are identified that are found to depend on Reynolds number. It is found that the recirculation region behind the cylinders is shorter than that of half cylinders placed on the wall representing the symmetry plane. Unlike a single cylinder, the separation point is found to always be on the rear of the cylinders, even at very low Reynolds number. Boundary layer transition is found to occur at much lower Reynolds numbers than previously reported.

Strouhal number of flat and flapped plates at moderate Reynolds number and different angles of attack: experimental data

2018 ◽  
Vol 230 (1) ◽  
pp. 333-349 ◽  
Author(s):  
Ali Bakhshandeh Rostami ◽  
Mohammad Mobasheramini ◽  
Antonio Carlos Fernandes
Keyword(s):  
Experimental Data ◽  
Reynolds Number ◽  
Strouhal Number ◽  
Moderate Reynolds Number

Pressure, Frictional Resistance, and Flow Characteristics of the Partially Wetted Rotating Disk

1968 ◽  
Vol 90 (2) ◽  
pp. 395-404 ◽  
Author(s):  
H. N. Ketola ◽  
J. M. McGrew
Keyword(s):  
Experimental Data ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Flow Characteristics ◽  
Frictional Resistance ◽  
Rotating Disk ◽  
Practical Applications ◽  
Stationary Wall ◽  
Spacing Ratio ◽  
Analytical Expressions

A theory of the partially wetted rotating disk is described and experimental data presented which verify the application of this theory in practical applications. Four different flow regimes may be identified according to the value of the disk Reynolds number and the spacing ratio between the disk and stationary wall. The analytical expressions for prediction of the pressure gradient developed and the frictional resistance are uniquely determined by the disk Reynolds number, spacing ratio, and the degree of wetting of the disk.

Fully developed MHD turbulence near critical magnetic Reynolds number

1981 ◽  
Vol 104 ◽  
pp. 419-443 ◽  
Author(s):  
J. Léorat ◽  
A. Pouquet ◽  
U. Frisch
Keyword(s):  
Reynolds Number ◽  
Kinetic Energy ◽  
Isotropic Turbulence ◽  
Magnetic Energy ◽  
Reynolds Numbers ◽  
Magnetic Reynolds Number ◽  
Mhd Equations ◽  
Liquid Sodium ◽  
Turbulent Heat ◽  
Mhd Turbulence

Liquid-sodium-cooled breeder reactors may soon be operating at magnetic Reynolds numbers RM where magnetic fields can be self-excited by a dynamo mechanism (as first suggested by Bevir 1973). Such flows have kinetic Reynolds numbers RV of the order of 107 and are therefore highly turbulent.This leads us to investigate the behaviour of MHD turbulence with high RV and low magnetic Prandtl numbers. We use the eddy-damped quasi-normal Markovian closure applied to the MHD equations. For simplicity we restrict ourselves to homogeneous and isotropic turbulence, but we do include helicity.We obtain a critical magnetic Reynolds number RMc of the order of a few tens (non-helical case) above which magnetic energy is present. RMc is practically independent of RV (in the range 40 to 106). RMc can be considerably decreased by the presence of helicity: when the overall size of the flow L is much larger than the integral scale l0, RMc can drop below unity as suggested by an α-effect argument. When L ≈ l0 the drop can still be substantial (factor of 6) when helicity is a maximum. We examine how the turbulence is modified when RM crosses RMc: presence of magnetic energy, decreased kinetic energy, steepening of kinetic-energy spectrum, etc.We make no attempt to obtain quantitative estimates for a breeder reactor, but discuss some of the possible consequences of exceeding RMc, such as decreased turbulent heat transport. More precise information may be obtained from numerical simulations and experiments (including some in the subcritical regime).

Turbulent kinetic energy production and flow structures in flows past smooth and rough walls

2019 ◽  
Vol 866 ◽  
pp. 897-928 ◽  
Author(s):  
P. Orlandi
Keyword(s):  
Reynolds Number ◽  
Kinetic Energy ◽  
Turbulent Kinetic Energy ◽  
Turbulent Flows ◽  
Energy Production ◽  
Compressive Strain ◽  
Turnover Time ◽  
Flow Structures ◽  
Wall Region ◽  
Rate Of Dissipation

Data available in the literature from direct numerical simulations of two-dimensional turbulent channels by Lee & Moser (J. Fluid Mech., vol. 774, 2015, pp. 395–415), Bernardini et al. (J. Fluid Mech., 742, 2014, pp. 171–191), Yamamoto & Tsuji (Phys. Rev. Fluids, vol. 3, 2018, 012062) and Orlandi et al. (J. Fluid Mech., 770, 2015, pp. 424–441) in a large range of Reynolds number have been used to find that $S^{\ast }$ the ratio between the eddy turnover time ($q^{2}/\unicode[STIX]{x1D716}$, with $q^{2}$ being twice the turbulent kinetic energy and $\unicode[STIX]{x1D716}$ the isotropic rate of dissipation) and the time scale of the mean deformation ($1/S$), scales very well with the Reynolds number in the wall region. The good scaling is due to the eddy turnover time, although the turbulent kinetic energy and the rate of isotropic dissipation show a Reynolds dependence near the wall; $S^{\ast }$, as well as $-\langle Q\rangle =\langle s_{ij}s_{ji}\rangle -\langle \unicode[STIX]{x1D714}_{i}\unicode[STIX]{x1D714}_{i}/2\rangle$ are linked to the flow structures, and also the latter quantity presents a good scaling near the wall. It has been found that the maximum of turbulent kinetic energy production $P_{k}$ occurs in the layer with $-\langle Q\rangle \approx 0$, that is, where the unstable sheet-like structures roll-up to become rods. The decomposition of $P_{k}$ in the contribution of elongational and compressive strain demonstrates that the two contributions present a good scaling. However, the good scaling holds when the wall and the outer structures are separated. The same statistics have been evaluated by direct simulations of turbulent flows in the presence of different types of corrugations on both walls. The flow physics in the layer near the plane of the crests is strongly linked to the shape of the surface and it has been demonstrated that the $u_{2}$ (normal to the wall) fluctuations are responsible for the modification of the flow structures, for the increase of the resistance and of the turbulent kinetic energy production.

Sign in / Sign up

Export Citation Format

Share Document