Sloshing Effects Accounting for Dynamic Coupling Between Vessel and Tank Liquid Motion

2007 ◽  
Author(s):  
Mirela Zalar ◽  
Louis Diebold ◽  
Eric Baudin ◽  
Jacqueline Henry ◽  
Xiao-Bo Chen
Keyword(s):  
Coupling Effect ◽  
Scale Model ◽  
Small Scale ◽  
Induced Response ◽  
Linear Potential ◽  
Dynamic Coupling ◽  
Liquid Motion ◽  
Violent Behaviour ◽  
Standard Size ◽  
Vessel Motion

Sloshing, a violent behaviour of liquid contents in tanks submitted to the forced vessels’ motion on the sea represents one of the major considerations in LNG vessels design over several past decades. State of the art of sloshing analysis relies on small-scale sloshing model tests supported by extensive developments of CFD computation techniques, commonly studying one isolated tank submitted to the forced motion without their mutual interaction. In reality, wave-induced response of the vessel carrying liquid cargo is affected by internal liquid motion, and consequently, tank liquid flow is altered by the vessel motion in return. An efficient numerical model for dynamic coupling between motions exerted by tank liquid (sloshing) and rigid body motions of the vessel (seakeeping) was developed in Bureau Veritas, formulated under the assumptions of linear potential theory in frequency domain. As already experienced with anti-rolling tanks, strong coupling effect is perceived on the first order transverse motions. However, consequences of coupled motions on sloshing loads have not been explored yet. This paper presents comparative analysis of sloshing effects induced by coupled and non-coupled vessel motion, introduced as the excitation to 6 d.o.f. small-scale model test rig. Possible risk of coupled effects is demonstrated on the example of standard size of LNG carrier operating with partly filled cargo tanks.

Simulation of Multiliquid-Layer Sloshing With Vessel Motion by Using Moving Particle Semi-Implicit Method

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Kyung Sung Kim ◽  
Moo-Hyun Kim ◽  
Jong-Chun Park
Keyword(s):  
Gas Production ◽  
Particle Simulation ◽  
Small Scale ◽  
Linear Potential ◽  
Operational Effectiveness ◽  
Mps Method ◽  
Moving Particle ◽  
Vessel Motion ◽  
Linear Potential Theory ◽  
Oil Gas

For oil/gas production/processing platforms, multiple liquid layers can exist and their respective sloshing motions can also affect operational effectiveness or platform performance. To numerically simulate those problems, a new multiliquid moving particle simulation (MPS) method is developed. In particular, to better simulate the relevant physics, robust self-buoyancy model, interface searching model, and surface-tension model are developed. The developed multiliquid MPS method is validated by comparisons against experiment in which three-liquid-sloshing experiment and the corresponding linear potential theory are given. The validated multiliquid MPS program is subsequently coupled with a vessel-motion program in time domain to investigate their dynamic-coupling effects. In case of multiple liquid layers, there exists a variety of sloshing natural frequencies for respective interfaces, so the relevant physics can be much more complicated compared with the single-liquid-tank case. The simulation program can also reproduce the detailed small-scale interface phenomenon called Kelvin–Helmholtz instability. The numerical simulations also show that properly designed liquid cargo tank can also function as a beneficial antirolling device.

On the Hydrodynamic Interaction Between Ship and Free-Surface Motions on Vessels With Moonpools

2019 ◽  
Author(s):  
Senthuran Ravinthrakumar ◽  
Trygve Kristiansen ◽  
Babak Ommani
Keyword(s):  
Free Surface ◽  
Flow Separation ◽  
Coupling Effect ◽  
Three Dimensional ◽  
Dimensional Case ◽  
Navier Stokes ◽  
Linear Potential ◽  
Two Dimensional ◽  
Sloshing Mode ◽  
Vessel Motion

Abstract Coupling between moonpool resonance and vessel motion is investigated in two-dimensional and quasi three-dimensional settings, where the models are studied in forced heave and in freely floating conditions. The two-dimensional setups are with a recess, while the quasi three-dimensional setups are without recess. One configuration with recess is presented for the two-dimensional case, while three different moonpool sizes (without recess) are tested for the quasi three-dimensional setup. A large number of forcing periods, and three wave steepnesses are tested. Boundary Element Method (BEM) and Viscous BEM (VBEM) time-domain codes based on linear potential flow theory, and a Navier–Stokes solver with linear free-surface and body-boundary conditions, are implemented to investigate resonant motion of the free-surface and the model. Damping due to flow separation from the sharp corners of the moonpool inlets is shown to matter for both vessel motions and moonpool response around the piston mode. In general, the CFD simulations compare well with the experimental results. BEM over-predicts the response significantly at resonance. VBEM provides improved results compared to the BEM, but still over-predicts the response. In the two-dimensional study there are significant coupling effects between heave, pitch and moonpool responses. In the quasi three-dimensional tests, the coupling effect is reduced significantly as the moonpool dimensions relative to the displaced volume of the ship is reduced. The first sloshing mode is investigated in the two-dimensional case. The studies show that damping due to flow separation is dominant. The vessel motions are unaffected by the moonpool response around the first sloshing mode.

RANCANG BANGUN PERANGKAT EKSPERIMENTASI PROSES PIROLISIS BIOMASA GELOMBANG MIKRO

2013 ◽  
Vol 14 (2) ◽  
Author(s):  
Noor Fachrizal
Keyword(s):  
Large Scale ◽  
Continuous Model ◽  
Biomass Energy ◽  
Scale Model ◽  
Small Scale ◽  
Laboratory Apparatus ◽  
Liquid Form ◽  
Large Scale Model ◽  
Bio Oil ◽  
Pyrolysis Of Biomass

Biomass such as agriculture waste and urban waste are enormous potency as energy resources instead of enviromental problem. organic waste can be converted into energy in the form of liquid fuel, solid, and syngas by using of pyrolysis technique. Pyrolysis process can yield higher liquid form when the process can be drifted into fast and flash response. It can be solved by using microwave heating method. This research is started from developing an experimentation laboratory apparatus of microwave-assisted pyrolysis of biomass energy conversion system, and conducting preliminary experiments for gaining the proof that this method can be established for driving the process properly and safely. Modifying commercial oven into laboratory apparatus has been done, it works safely, and initial experiments have been carried out, process yields bio-oil and charcoal shortly, several parameters are achieved. Some further experiments are still needed for more detail parameters. Theresults may be used to design small-scale continuous model of productionsystem, which then can be developed into large-scale model that applicable for comercial use.

scholarly journals Experimental Study on the Behavior of Existing Reinforced Concrete Multi-Column Piers under Earthquake Loading

2021 ◽  
Vol 11 (6) ◽  
pp. 2652
Author(s):  
Jung Han Kim ◽  
Ick-Hyun Kim ◽  
Jin Ho Lee
Keyword(s):  
Seismic Performance ◽  
Seismic Design ◽  
Bridge Piers ◽  
Scale Model ◽  
Inertia Force ◽  
Small Scale ◽  
Lap Splice ◽  
Existing Structures ◽  
Seismic Design Code ◽  
Seismic Force

When a seismic force acts on bridges, the pier can be damaged by the horizontal inertia force of the superstructure. To prevent this failure, criteria for seismic reinforcement details have been developed in many design codes. However, in moderate seismicity regions, many existing bridges were constructed without considering seismic detail because the detailed seismic design code was only applied recently. These existing structures should be retrofitted by evaluating their seismic performance. Even if the seismic design criteria are not applied, it cannot be concluded that the structure does not have adequate seismic performance. In particular, the performance of a lap-spliced reinforcement bar at a construction joint applied by past practices cannot be easily evaluated analytically. Therefore, experimental tests on the bridge piers considering a non-seismic detail of existing structures need to be performed to evaluate the seismic performance. For this reason, six small scale specimens according to existing bridge piers were constructed and seismic performances were evaluated experimentally. The three types of reinforcement detail were adjusted, including a lap-splice for construction joints. Quasi-static loading tests were performed for three types of scale model with two-column piers in both the longitudinal and transverse directions. From the test results, the effect on the failure mechanism of the lap-splice and transverse reinforcement ratio were investigated. The difference in failure characteristics according to the loading direction was investigated by the location of plastic hinges. Finally, the seismic capacity related to the displacement ductility factor and the absorbed energy by hysteresis behavior for each test were obtained and discussed.

Wave Energy Hyperbaric Device for Electricity Production

2007 ◽  
Author(s):  
Segen F. Estefen ◽  
Paulo Roberto da Costa ◽  
Eliab Ricarte ◽  
Marcelo M. Pinheiro
Keyword(s):  
Power Generation ◽  
Wave Energy ◽  
Experimental Results ◽  
Electricity Production ◽  
Scale Model ◽  
Small Scale ◽  
Regular Waves ◽  
Hyperbaric Chamber ◽  
Small Scale Model

Wave energy is a renewable and non-polluting source and its use is being studied in different countries. The paper presents an overview on the harnessing of energy from waves and the activities associated with setting up a plant for extracting energy from waves in Port of Pecem, on the coast of Ceara State, Brazil. The technology employed is based on storing water under pressure in a hyperbaric chamber, from which a controlled jet of water drives a standard turbine. The wave resource at the proposed location is presented in terms of statistics data obtained from previous monitoring. The device components are described and small scale model tested under regular waves representatives of the installation region. Based on the experimental results values of prescribed pressures are identified in order to optimize the power generation.

scholarly journals Roughness Lengths for Momentum and Heat Derived from Outdoor Urban Scale Models

2007 ◽  
Vol 46 (7) ◽  
pp. 1067-1079 ◽  
Author(s):  
M. Kanda ◽  
M. Kanega ◽  
T. Kawai ◽  
R. Moriwaki ◽  
H. Sugawara
Keyword(s):  
Wind Direction ◽  
Roughness Length ◽  
Scale Dependence ◽  
Scale Model ◽  
Small Scale ◽  
Physical Scale ◽  
Scale Models ◽  
Roughness Lengths ◽  
Urban Sites ◽  
Obstacle Height

Abstract Urban climate experimental results from the Comprehensive Outdoor Scale Model (COSMO) were used to estimate roughness lengths for momentum and heat. Two different physical scale models were used to investigate the scale dependence of the roughness lengths; the large scale model included an aligned array of 1.5-m concrete cubes, and the small scale model had a geometrically similar array of 0.15-m concrete cubes. Only turbulent data from the unstable boundary layers were considered. The roughness length for momentum relative to the obstacle height was dependent on wind direction, but the scale dependence was not evident. Estimated values agreed well with a conventional morphometric relationship. The logarithm of the roughness length for heat relative to the obstacle height depended on the scale but was insensitive to wind direction. COSMO data were used successfully to regress a theoretical relationship between κB−1, the logarithmic ratio of roughness length for momentum to heat, and Re*, the roughness Reynolds number. Values of κB−1 associated with Re* for three different urban sites from previous field experiments were intercompared. A surprising finding was that, even though surface geometry differed from site to site, the regressed function agreed with data from the three urban sites as well as with the COSMO data. Field data showed that κB−1 values decreased as the areal fraction of vegetation increased. The observed dependency of the bulk transfer coefficient on atmospheric stability in the COSMO data could be reproduced using the regressed function of Re* and κB−1, together with a Monin–Obukhov similarity framework.

Staged-Air Ratio Optimization for a New Down-Fired Technology within a Cold Small-Scale Model of a 350 MWeUtility Boiler

2011 ◽  
Vol 25 (4) ◽  
pp. 1485-1496 ◽  
Author(s):  
Min Kuang ◽  
Zhengqi Li ◽  
Pengfei Yang ◽  
Jinzhao Jia ◽  
Qunyi Zhu
Keyword(s):  
Scale Model ◽  
Small Scale ◽  
Ratio Optimization ◽  
Small Scale Model

Differences in the Upscaling Procedure for Compositional Reservoir Simulations of Immiscible and Miscible Gas Flooding

2021 ◽  
Author(s):  
Victor de Souza Rios ◽  
Arne Skauge ◽  
Ken Sorbie ◽  
Gang Wang ◽  
Denis José Schiozer ◽  
...  
Keyword(s):  
Computational Cost ◽  
Specific Treatment ◽  
Dynamic Responses ◽  
Scale Model ◽  
Small Scale ◽  
Coarse Scale ◽  
Reservoir Models ◽  
Permeability Upscaling ◽  
Gas Flooding ◽  
Grid Block

Abstract Compositional reservoir simulation is essential to represent the complex interactions associated with gas flooding processes. Generally, an improved description of such small-scale phenomena requires the use of very detailed reservoir models, which impact the computational cost. We provide a practical and general upscaling procedure to guide a robust selection of the upscaling approaches considering the nature and limitations of each reservoir model, exploring the differences between the upscaling of immiscible and miscible gas injection problems. We highlight the different challenges to achieve improved upscaled models for immiscible and miscible gas displacement conditions with a stepwise workflow. We first identify the need for a special permeability upscaling technique to improve the representation of the main reservoir heterogeneities and sub-grid features, smoothed during the upscaling process. Then, we verify if the use of pseudo-functions is necessary to correct the multiphase flow dynamic behavior. At this stage, different pseudoization approaches are recommended according to the miscibility conditions of the problem. This study evaluates highly heterogeneous reservoir models submitted to immiscible and miscible gas flooding. The fine models represent a small part of a reservoir with a highly refined set of grid-block cells, with 5 × 5 cm2 area. The upscaled coarse models present grid-block cells of 8 × 10 m2 area, which is compatible with a refined geological model in reservoir engineering studies. This process results in a challenging upscaling ratio of 32 000. We show a consistent procedure to achieve reliable results with the coarse-scale model under the different miscibility conditions. For immiscible displacement situations, accurate results can be obtained with the coarse models after a proper permeability upscaling procedure and the use of pseudo-relative permeability curves to improve the dynamic responses. Miscible displacements, however, requires a specific treatment of the fluid modeling process to overcome the limitations arising from the thermodynamic equilibrium assumption. For all the situations, the workflow can lead to a robust choice of techniques to satisfactorily improve the coarse-scale simulation results. Our approach works on two fronts. (1) We apply a dual-porosity/dual-permeability upscaling process, developed by Rios et al. (2020a), to enable the representation of sub-grid heterogeneities in the coarse-scale model, providing consistent improvements on the upscaling results. (2) We generate specific pseudo-functions according to the miscibility conditions of the gas flooding process. We developed a stepwise procedure to deal with the upscaling problems consistently and to enable a better understanding of the coarsening process.

Sign in / Sign up

Export Citation Format

Share Document