Microstructural Stability and Lattice Misfit Characterisations of Nimonic 263

2012 ◽  
Author(s):  
Quanshun Luo ◽  
Kuangnan Chi ◽  
Shuxin Li ◽  
Pete Barnard
Keyword(s):  
Grain Boundary ◽  
Morphological Evolution ◽  
Lattice Misfit ◽  
Initial Growth ◽  
Microstructural Stability ◽  
Gaussian Peak ◽  
Hardening Treatment ◽  
The Matrix ◽  
Matrix Lattice ◽  
Average Size

Nimonic 263 has been selected as a candidate header/piping material of advanced ultra-supercritical (A-USC) boilers for the next generation of fossil fuel power plant. Experimental assessments on the microstructural stability of this material are presented in this paper. Microstructural evolution has been quantified by high resolution field emission SEM and TEM. Electron diffraction and the combined XRD and Gaussian peak-fitting have been applied to investigate the coherency and lattice misfit between the gamma prime (γ′) precipitates and the gamma (γ) matrix. The micro structure subjected to solution and hardening treatment consists of γ-matrix and a network of carbide precipitates along the grain boundaries. Large quantities of fine γ′-Ni3(Ti,Al) precipitates were observed, with an average size of 17 nm and coherent with the matrix lattice. The overall misfit has been quantified to be 0.28%. After long term aging at 700 and 725 °C for various periods up to 20,000 hours, γ′ was still the predominant precipitate and mostly coherent with the matrix. A few needle-shape η-Ni3Ti intermetallic precipitates were found in the grain boundary regions. The γ′ size has grown progressively to 78 nm, accompanied by the γ′-γ constrained misfit increasing to 0.50%. Moreover, the M23C6-type grain boundary carbides were found to have experienced morphological evolution, including the nucleation of Widmanstatten-type needles and their initial growth towards the matrix.

scholarly journals Lattice Misfit of High Refractory Ruthenium Containing Nickel-Base Superalloys

2011 ◽  
Vol 278 ◽  
pp. 60-65 ◽  
Author(s):  
Steffen Neumeier ◽  
J. Ang ◽  
R.A. Hobbs ◽  
Catherine M.F. Rae ◽  
Howard J. Stone
Keyword(s):  
Lattice Misfit ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
The Matrix ◽  
Coherency Stress ◽  
Matrix Lattice ◽  
Chemical Segregation ◽  
Nickel Base Superalloys ◽  
Nickel Base

The influence of Ru, Co, Mo and W on the lattice misfit of eight highly alloyed Re containing single crystal nickel-base superalloys was investigated. High resolution X-ray diffraction (XRD) was used to relate the elemental partitioning behavior and the Vegard coefficients of the elements under investigation to the measured lattice parameter of the  and  phase. The residual chemical segregation and especially the coherency stress-induced tetragonal distortion of the  matrix lattice in the high Mo containing alloys results in the observation of two different lattice parameters for the  matrix phase. This leads to three overlapping, but clearly distinguishable {002} X-ray reflections.

Effects of microstructure and lattice misfit on creep life of Ni-based single crystal superalloy during long-term thermal exposure

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Wenyan Gan ◽  
Hangshan Gao ◽  
Haiqing Pei ◽  
Zhixun Wen
Keyword(s):  
Single Crystal ◽  
Rupture Life ◽  
Precipitation Amount ◽  
Lattice Misfit ◽  
Thermal Exposure ◽  
Phase Evolution ◽  
Creep Rupture ◽  
Simultaneous Increase ◽  
Creep Life ◽  
The Matrix

Abstract According to the microstructural evolution during longterm thermal exposure at 1100 °C, the creep rupture life of Ni-based single crystal superalloys at 980 °C/270 MPa was evaluated. The microstructure was characterized by means of scanning electron microscopy, X-ray diffraction and related image processing methods. The size of γ’ precipitates and the precipitation amount of topologically close-packed increased with the increase in thermal exposure time, and coarsening of the γ’ precipitates led to the simultaneous increase of the matrix channel width. The relationship between the creep rupture life and the lattice misfit of γ/γ’, the coarsening of γ’ precipitate and the precipitation of TCP phase are systematically discussed. In addition, according to the correlation between γ’ phase evolution and creep characteristics during thermal exposure, a physical model is established to predict the remaining creep life.

scholarly journals Influence of Alumina Nanofibers Sintered by the Spark Plasma Method on Nickel Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 548 ◽  
Author(s):  
Leonid Agureev ◽  
Valeriy Kostikov ◽  
Zhanna Eremeeva ◽  
Svetlana Savushkina ◽  
Boris Ivanov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Strength Properties ◽  
Alumina Nanoparticles ◽  
Metal Powders ◽  
Wide Range ◽  
The Matrix ◽  
Spark Plasma ◽  
Average Size

The article presents the study of alumina nanoparticles’ (nanofibers) concentration effect on the strength properties of pure nickel. The samples were obtained by spark plasma sintering of previously mechanically activated metal powders. The dependence of the grain size and the relative density of compacts on the number of nanofibers was investigated. It was found that with an increase in the concentration of nanofibers, the average size of the matrix particles decreased. The effects of the nanoparticle concentration (0.01–0.1 wt.%) on the elastic modulus and tensile strength were determined for materials at 25 °C, 400 °C, and 750 °C. It was shown that with an increase in the concentration of nanofibers, a 10–40% increase in the elastic modulus and ultimate tensile strength occurred. A comparison of the mechanical properties of nickel in a wide range of temperatures, obtained in this work with materials made by various technologies, is carried out. A description of nanofibers’ mechanisms of influence on the structure and mechanical properties of nickel is given. The possible impact of impurity phases on the properties of nickel is estimated. The tendency of changes in the mechanical properties of nickel, depending on the concentration of nanofibers, is shown.

Observation of Growth Front on the Initial Stage of Goss Abnormally-Growing Grain in Fe-3%Si Steel

2013 ◽  
Vol 753 ◽  
pp. 307-310
Author(s):  
Kyung Jun Ko ◽  
Jong Tae Park ◽  
Chan Hee Han
Keyword(s):  
Solid State ◽  
Grain Boundary ◽  
Three Dimensional ◽  
Secondary Recrystallization ◽  
Growth Front ◽  
Very High Frequency ◽  
Grain Boundary Mobility ◽  
Initial Stage ◽  
The Matrix

During abnormal grain growth, a few Goss grains grow exclusively fast and consume the matrix grains. The Goss abnormally-growing grain (AGG) has peculiar features which are irregular grain boundaries and very high frequency of peninsular grains nearby the growth front of AGG and island grains trapped inside AGG. These features might provide a clue for clarifying the mechanism of Goss AGG. The experimentally-observed microstructural feature and grain boundary characterization of Goss were approached by the solid-state wetting mechanism. In this study, observing the three-dimensional wetting morphology in serial section images of Goss AGG by EBSD, we report some direct microstrucrual evidence supporting solid-state wetting mechanism for Goss AGG. The solid-state wetting mechanism for the evolution of the Goss AGG in Fe-3%Si steel explains the microstructural features evolved during secondary recrystallization, which cannot be approached by the conventional theories based on the grain boundary mobility.

Small Lead and Indium Inclusions in Aluminium

1991 ◽  
Vol 235 ◽  
Author(s):  
E. Johnson ◽  
K. Hjemsted ◽  
B. Schmidt ◽  
K. K. Bourdelle ◽  
A. Johansen ◽  
...  
Keyword(s):  
Melting Point ◽  
Elevated Temperatures ◽  
Supersaturated Solution ◽  
In Situ Tem ◽  
Initial Growth ◽  
Heating And Cooling ◽  
Moiré Fringes ◽  
The Matrix ◽  
Spontaneous Phase

ABSTRACTIon implantation of lead or indium into aluminium results in spontaneous phase separation and formation of lead or indium precipitates. The precipitates grow in topotactical alignment with the matrix, giving TEM images characterized by moiré fringes. The size and density of the precipitates increase with increasing fluence until coalescence begins to occur. Implantations at elevated temperatures lead to formation of larger precipitates with well developed facets. This is particularly significant for implantations above the bulk melting point of the implanted species. Melting and solidification have been followed by in-situ TEM heating and cooling experiments. Superheating up to ∼ 50 K above the bulk melting point has been observed, and the largest inclusions melt first. Melting is associated with only partial loss of facetting of the largest inclusions. Initial growth of the inclusions occurs by trapping of atoms retained in supersaturated solution. Further growth occurs by coalescence of neighbouring inclusions in the liquid phase. Solidification is accompanied by a strong undercooling ∼ 30 K below the bulk melting point, where the smallest inclusions solidify first. Solidification is characterized by spontaneous restoration of the facets and the topotactical alignment.

scholarly journals Character evolution of modern fly-speck fungi and implications for interpreting thyriothecial fossils

2020 ◽  
Author(s):  
Ludovic Le Renard ◽  
André L. Firmino ◽  
Olinto L. Pereira ◽  
Ruth A. Stockey ◽  
Mary. L. Berbee
Keyword(s):  
Morphological Evolution ◽  
Morphological Characters ◽  
Small Subunit ◽  
Leaf Surfaces ◽  
The Matrix ◽  
Character Matrix ◽  
Phylogenetic Framework ◽  
Single Hypha ◽  
Objective Basis ◽  
Ancestral Character States

AbstractPREMISE OF THE STUDYFossils show that fly-speck fungi have been reproducing with small, black thyriothecia on leaf surfaces for ∼250 million years. We analyze morphological characters of extant thyriothecial fungi to develop a phylogenetic framework for interpreting fossil taxa.METHODSWe placed 59 extant fly-speck fungi in a phylogeny of 320 Ascomycota using nuclear ribosomal large and small subunit sequences, including newly determined sequences from nine taxa. We reconstructed ancestral character states using BayesTraits and maximum likelihood after coding 11 morphological characters based on original observations and literature. We analyzed the relationships of three previously published Mesozoic fossils using parsimony and our morphological character matrix, constrained by the molecular phylogeny.KEY RESULTSThyriothecia evolved convergently in multiple lineages of superficial, leaf- inhabiting ascomycetes. The radiate and ostiolate scutellum organization is restricted to Dothideomycetes. Scutellum initiation by intercalary septation of a single hypha characterizes Asterinales and Asterotexiales, and initiation by coordinated growth of two or more adjacent hyphae characterizes Aulographaceae (order incertae sedis). Scutella in Microthyriales are initiated apically on a lateral hyphal branch. Patterns of hyphal branching in scutella contribute to distinguishing among orders. Parsimony resolves three fossil taxa as Dothideomycetes; one is further resolved as a member of a Microthyriales-Zeloasperisporiales clade within Dothideomycetes.CONCLUSIONSThis is the most comprehensive systematic study of thyriothecial fungi and their relatives to date. Parsimony analysis of the matrix of character states of modern taxa provides an objective basis for interpreting fossils, leading to insights into morphological evolution and geological ages of Dothideomycetes clades.

Simulation of Microstructural Evolution during Superplastic Deformation

1999 ◽  
Vol 601 ◽  
Author(s):  
B.-N. Kim ◽  
K. Hiraga
Keyword(s):  
Aspect Ratio ◽  
Grain Boundary ◽  
Grain Growth ◽  
Boundary Diffusion ◽  
Tensile Deformation ◽  
Grain Boundary Diffusion ◽  
Initial Value ◽  
The Matrix ◽  
Dynamic Growth ◽  
Equiaxed Grains

AbstractSuperplastic tensile deformation is simulated in 2 dimensions by incorporating grain boundary diffusion and concurrent grain growth derived from static and dynamic growth mechanisms. The following relationship is found between microstructural changes and deformation behavior for constant stress conditions. Grain boundary diffusion produces an increase in the aspect ratio of the matrix grains during deformation and the increased aspect ratio causes a change in creep rate parameters: the stress exponent is decreased from the initial value of 1.0 for equiaxed grains and the grain size exponent is increased from the initial value of 3.0. Accelerated grain growth is also found by the present simulation.

Effect of Heat-Treatment Time on Microstructure and Mechanical Properties of Mg-5Gd-2Y-2Zn-0.5Zr Alloy

2012 ◽  
Vol 482-484 ◽  
pp. 1384-1389 ◽  
Author(s):  
Ling Gang Meng ◽  
Can Feng Fang ◽  
Peng Peng ◽  
Nai Pu Li ◽  
Qiong Zhu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Grain Boundary ◽  
Treatment Time ◽  
Time Range ◽  
Lpso Phase ◽  
High Temperature Heat Treatment ◽  
Lpso Structure ◽  
The Matrix ◽  
New Type ◽  
The Stability

Microstructure evolution of Mg-5Gd-2Y-2Zn-0.5Zr alloy during high temperature heat-treatment at 500°C in the time range 10-70h was investigated. The results show that after adding the element Y, the as-cast Mg-5Gd-2Y-2Zn-0.5Zr alloy forms the Mg12Zn(Y,Gd) phase with 18R-LPSO structure at the grain boundary. During heat-treatment at 500°C, the stability of 18R-LPSO structure is weakened by Gd atoms, parts of LPSO phases dissolve gradually into the matrix with time prolonged and a new type Mg(Y,Gd)Zn phase come into being. LPSO phase in the grain boundary can ensure the ultimate tensile strength and elongation of the alloy, and effect of dissevering on the LPSO phase by Mg(Gd,Y)Zn phase results the decrease of UTS and elongation.

Effect of Two-Stage Aging on Microstructure and Properties of Al-Mg-Si Alloys

2022 ◽  
Vol 905 ◽  
pp. 51-55
Author(s):  
Li Wang ◽  
Ya Ya Zheng ◽  
Shi Hu Hu
Keyword(s):  
Growth Rate ◽  
Grain Boundary ◽  
Tensile Properties ◽  
Tensile Testing ◽  
Diffusion Rate ◽  
Two Stage ◽  
Precipitated Phase ◽  
Transmission Electron ◽  
The Matrix ◽  
Microstructure Characteristic

The effects of two-stage aging on the microstructures, tensile properties and intergranular corrosion (IGC) sensitivity of Al-Mg-Si alloys were studied by tensile testing and IGC experiments and transmission electron microscope (TEM). The results show that the two-stage aging (180°C, 2h+160°C, 120h) can reduce the IGC sensitivity without decrease the tensile properties. The grain is distributed with high-density β′′ phases, and the grain boundary phases are spherical and intermittently distributed. The formation of the microstructure characteristic is due to the lower re-aging temperature, which results in a decline differences in the diffusion rate between the matrix and grain boundaries. As a result, the pre-precipitated phase can maintain a better strengthening effects due to the slower growth rate. The pre-precipitated phase of the grain boundary presents a spherical and intermittent distribution due to the fast coarsening speed.

Sign in / Sign up

Export Citation Format

Share Document