HIGH-TEMPERATURE TRIBOLOGICAL BEHAVIORS OF TiNi/Ti2Ni ALLOYED LAYER ON SURFACE OF Ti6Al4V ALLOY

2017 ◽  
Vol 24 (03) ◽  
pp. 1750028 ◽  
Author(s):  
ZHENXIA WANG ◽  
HAIRUI WU ◽  
NAIMING LIN ◽  
XIAOHONG YAO ◽  
ZHIYONG HE ◽  
...  
Keyword(s):  
High Temperature ◽  
Friction Coefficient ◽  
Friction And Wear ◽  
Room Temperature ◽  
Alloyed Layer ◽  
Surface Alloying ◽  
Wear Performance ◽  
Ti6al4v Substrate ◽  
Oxidation Wear ◽  
Plasma Surface Alloying

Plasma surface alloying (PSA) technique was employed with nickel as incident ions to prepare the TiNi/Ti2Ni alloyed layer on surface of Ti6Al4V. High-temperature friction and wear performance of TiNi/Ti2Ni alloyed layer and the Ti6Al4V substrate were evaluated at 500[Formula: see text]C. The results indicated that the TiNi/Ti2Ni alloyed layer exhibited superior high-temperature wear performance. The variations of friction coefficient were the same rule but wear rate was lower compared to Ti6Al4V substrate. The wear mechanism of TiNi/Ti2Ni alloyed layer was mainly slight abrasion and the Ti6Al4V substrate showed abrasion and oxidation wear. The friction coefficient of the TiNi/Ti2Ni alloyed layer decreased from 0.90 to 0.50 with the increase of temperature from room temperature to 500[Formula: see text]C.

FRICTION AND WEAR BEHAVIORS OF Ti6Al4V ALLOY TREATED BY PLASMA Ni ALLOYING

2018 ◽  
Vol 25 (05) ◽  
pp. 1850096
Author(s):  
ZHENXIA WANG ◽  
WENLAN CAI ◽  
HAIRUI WU ◽  
NAIMING LIN ◽  
XIAOHONG YAO ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Wear Mechanism ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Displacement Amplitude ◽  
Ti6al4v Substrate ◽  
Abrasion Wear ◽  
Modified Layer ◽  
Plasma Surface Alloying Technique ◽  
Plasma Surface Alloying

The Ni modified layer was prepared on surface of the Ti6Al4V substrate by plasma surface alloying technique (PSAT). The cross-section micro structure, phase structure and microhardness of Ni modified layer were studied. The friction and wear behavior of the Ni modified layer and the Ti6Al4V substrate were analysed. The effects of displacement amplitude, frequency and fretting time on friction coefficient of the Ni modified layer were investigated. The results indicated that the wear rate was lower compared with that of the Ti6Al4V substrate. Friction coefficient of the Ni modified layer increased with the increase of frequency. But it was insensitive to the change of wear time and the displacement amplitude. The wear mechanism of the Ti6Al4V was adhesion and abrasion wear mechanism while the Ni modified layer showed slightly abrasion wear.

The Reduction of Adhesion by Ion Implantation

1985 ◽  
Vol 107 (4) ◽  
pp. 467-471 ◽  
Author(s):  
M. Hirano ◽  
S. Miyake
Keyword(s):  
Friction Coefficient ◽  
Ion Implantation ◽  
Friction And Wear ◽  
Room Temperature ◽  
Wear Track ◽  
Friction Test ◽  
Wear Performance ◽  
Boron Implantation ◽  
Argon Ion ◽  
Plate Geometry

The effects of boron and argon ion implantation on the tribological characteristics of SUS440C stainless steel, sliding against a SUS440C ball (unimplanted) were investigated at room temperature using a friction test apparatus employing a ball-plate geometry in the absence of a lubricant. Wear performance was estimated using a profilometer tracing of the specimen wear track. Boron implantation reduced both the friction and wear of SUS440C. The friction coefficient of SUS440C was reduced from 0.75 to 0.15. SEM observations of wear track topography suggest that the reduction of the friction coefficient can be attributed to reduced adhesion due to boron implantation. The friction coefficient of the boron implanted layer decreased with an increase in the total ion dose. Argon implantation was carried out to distinguish the effects of implantation from the influence of contamination. Argon implantation increased the friction coefficient from 0.8 to 1.0 in contrast with boron implantation.

Study on Tribological Performance of the TiNi Modified Layer on the Surface of the Ti6Al4V Alloy

2011 ◽  
Vol 687 ◽  
pp. 759-764 ◽  
Author(s):  
Zhen Xia Wang ◽  
Zhi Yong He ◽  
Ying Qin Wang ◽  
Xiao Ping Liu ◽  
Bin Tang
Keyword(s):  
Tribological Performance ◽  
Ti6al4v Alloy ◽  
Alloyed Layer ◽  
Surface Alloying ◽  
Composition Distribution ◽  
Ti6al4v Substrate ◽  
Pin On Disc ◽  
Distribution Phase ◽  
Modified Layer ◽  
Plasma Surface Alloying

TiNi alloyed layer was prepared on surface of Ti6Al4V substrate by plasma surface alloying process. Micro-structure, composition distribution, phase structure and hardness distributing of TiNi modified layer were analyzed. Tribological performance of TiNi alloyed layer and Ti6Al4V substrate was observed by Pin-on-disc test. The results indicated that surface microhardness of TiNi alloyed layer was about 620HV. Coefficient of friction (CoF) and relative wear rate (RWR) of TiNi alloyed layer were lower than Ti6Al4V substrate, and wear resistance of TiNi alloyed layer was improved obviously. The wear mechanism of Ti6Al4V alloy is abrasion and adhesion wearing, while TiNi alloyed layer shows abrasion wearing.

Oil-soluble ionic liquid to lubricate silicon

2021 ◽  
pp. 135065012098488
Author(s):  
Waleed Al-Sallami ◽  
Pourya Parsaeian ◽  
Abdel Dorgham ◽  
Anne Neville
Keyword(s):  
Ionic Liquid ◽  
High Temperature ◽  
Friction And Wear ◽  
Tribological Performance ◽  
Considerable Reduction ◽  
Zinc Dialkyldithiophosphate ◽  
Lubrication Mechanism ◽  
Wear Coefficient ◽  
Wear Performance ◽  
Micro Scale

Trihexyltetradecylphosphonium bis(2-ethylhexyl)phosphate (phosphonium phosphate) ionic liquid is soluble in non-polar lubricants. It has been proposed as an effective anti-wear additive comparable to zinc dialkyldithiophosphate. Previously, phosphonium phosphate has shown a better anti-wear performance under some conditions such as high temperature. In this work, the tribological performance and the lubrication mechanism of phosphonium phosphate are compared with that of zinc dialkyldithiophosphate when lubricating silicon under various tribological conditions. This can lead to an understanding of the reasons behind the superior anti-wear performance of phosphonium phosphate under some conditions. A micro-scale study is conducted using a nanotribometer. The results show that both additives lead to a considerable reduction in both friction and wear coefficients. The reduction in the wear coefficient is mainly controlled by the formation of the tribofilm on the rubbing surfaces. Zinc dialkyldithiophosphate can create a thicker tribofilm, which results in a better anti-wear performance. However, the formation of a thicker film will lead to a faster depletion and thus phosphonium phosphate can provide better anti-wear performance when the depletion of zinc dialkyldithiophosphate starts.

Tribological Behavior of Mesophase Carbon Added with Titanium and Copper

2011 ◽  
Vol 80-81 ◽  
pp. 60-63
Author(s):  
Xue Qing Yue ◽  
Hua Wang ◽  
Shu Ying Wang
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Friction Coefficient ◽  
Ball Mill ◽  
Friction And Wear ◽  
Applied Load ◽  
Tribological Behavior ◽  
Metallic Elements ◽  
X Ray Diffraction ◽  
X Ray

Incorporation of metallic elements, titanium and copper, into carbonaceous mesophase (CM) was performed through mechanical alloying in a ball mill apparatus. The structures of the raw CM as well as the Ti/Cu-added CM were characterized by X-ray diffraction. The tribological behavior of the Ti/Cu-added CM used as lubricating additives was investigated by using a high temperature friction and wear tester. The results show that, compared with the raw CM, the Ti/Cu-added CM exhibits a drop in the crystallinity and a transition to the amorphous. The Ti/Cu-added CM used as lubricating additive displays an obvious high temperature anti-friction and wear resistance effect, and the lager the applied load, the lower the friction coefficient and the wear severity.

A Brief Overview on High Temperature Friction and Wear

2010 ◽  
Author(s):  
Mustafa Bulut Coskun ◽  
Mahmut Faruk Aksit
Keyword(s):  
High Temperature ◽  
Gas Turbines ◽  
Friction And Wear ◽  
Oxidation Behavior ◽  
Elevated Temperatures ◽  
Wear Performance ◽  
Large Pressure ◽  
Higher Power ◽  
Vibratory Motion ◽  
Increasing Temperature

With the race for higher power and efficiency new gas turbines operate at ever increasing pressures and temperatures. Increased compression ratios and firing temperatures require many engine parts to survive extended service hours under large pressure loads and thermal distortions while sustaining relative vibratory motion. On the other hand, wear at elevated temperatures limits part life. Combined with rapid oxidation for most materials wear resistance reduces rapidly with increasing temperature. In order to achieve improved wear performance at elevated temperatures better understanding of combined wear and oxidation behavior of high temperature super alloys and coatings needed. In an attempt to aid designers for high temperature applications, this work provides a quick reference for the high temperature friction and wear research available in open literature. High temperature friction and wear data have been collected, grouped and summarized in tables.

The friction and wear performance of plasma-sprayed ceramic coatings at high temperature

Wear ◽  
1989 ◽  
Vol 129 (2) ◽  
pp. 223-234 ◽  
Author(s):  
Yinglong Wang ◽  
Yuansheng Jin ◽  
Shizhu Wen
Keyword(s):  
High Temperature ◽  
Friction And Wear ◽  
Ceramic Coatings ◽  
Wear Performance ◽  
Plasma Sprayed

scholarly journals Microstructures and high-temperature self-lubricating wear-resistance mechanisms of graphene-modified WC-12Co coatings

Friction ◽  
2020 ◽  
Vol 9 (2) ◽  
pp. 315-331 ◽  
Author(s):  
Haoliang Tian ◽  
Changliang Wang ◽  
Mengqiu Guo ◽  
Yongjing Cui ◽  
Junguo Gao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
High Temperature ◽  
Friction Coefficient ◽  
Adhesive Strength ◽  
Friction And Wear ◽  
Resistance Mechanisms ◽  
High Temperature Treatment ◽  
Wear Properties ◽  
Powder Preparation ◽  
Wear Resistant

AbstractTo reduce the friction coefficient of cobalt-cemented tungsten carbide (WC-12Co) wear-resistant coatings, graphene was compounded into WC-12Co powder via wet ball milling and spray granulation. Self-lubricating and wear-resistant graphene coatings were prepared via detonation gun spraying. The presence, morphologies, and phase compositions of graphene in the powders and coatings that are obtained through different powder preparation processes were analyzed. The analysis was performed using the following technologies: energy-dispersive X-ray-spectroscopy (EDXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectroscopy. The mechanical properties of the coatings were studied using a microhardness tester and a universal drawing machine. The friction and wear properties of the coatings were studied using an SRV-4 friction and wear tester. The results showed that the graphene content in the WC-12Co coating modified with graphene was higher than that without modification; graphene was embedded in the structure in a transparent and thin-layer state. The adhesive strength of this coating at approximately 25 °C was approximately 60.33 MPa, and the hardness was approximately 984 HV0.3. After high-temperature treatment, the adhesive strength and hardness of the graphene oxide (GO)/WC-12Co coating decreased slightly (the lowest adhesive strength of 53.16 MPa was observed after treatment at 400 °C, and the lowest hardness of approximately 837 HV0.3 was observed after treatment at 300 °C). Compared to the friction coefficient (0.6) of the WC-12Co coating obtained at room temperature, the friction coefficient of the GO/WC-12Co coating was decreased by approximately 50% of that value. The graphene-modified coating was continuously exposed to the wear tracks on the surface of the contacting materials during friction, and a lubricating film was formed in the microareas in which the wear tracks were present. The coating exhibited improved self-lubricating and wear-resistant effects compared to the unmodified WC-12Co coating. The results of this study demonstrated that graphene could be effective in self-lubrication and wear-reduction in a temperature range of 100–200 °C, as a friction coefficient of 0.3 was maintained.

The Friction and Wear of Thin, Sintered, Fluoride Films

1972 ◽  
Vol 94 (1) ◽  
pp. 12-18 ◽  
Author(s):  
M. T. Lavik ◽  
B. D. McConnell ◽  
G. David Moore
Keyword(s):  
Friction Coefficient ◽  
Friction And Wear ◽  
Room Temperature ◽  
Wear Behavior ◽  
Strong Dependence ◽  
Aluminum Phosphate ◽  
Friction And Wear Behavior ◽  
Wear Life ◽  
Compositional Changes ◽  
Cure Temperature

Results are presented for the bonding of thin, sintered, fluoride films of BaF2 and CaF2 with mono-aluminum phosphate. Friction and wear behavior of these films has been defined in terms of film compositional changes, film curing procedures, and substrate variations when subjected to varying levels of temperature and load. Mono-aluminum phosphate was found to greatly enhance the adhesion of the sintered fluoride film. There was a strong dependence of wear life at 1000 deg F on the mono-aluminum phosphate content of the film. Films containing 6 vol. percent phosphate appear to be near optimum and exhibited wear lives of 1,000,000 load cycles under sliding conditions in a dual rub-shoe device with friction coefficient levels in the order of 0.10 to 0.20. Near-optimum values were determined for cure temperature (950 deg C), and surface finish (23 μ in. rms) on rhodium-plated substrates. Graphite and gold were added to the aluminum phosphate bonded BaF2: CaF2 films. Both additives were found to lower the friction coefficient at room temperature.

Sign in / Sign up

Export Citation Format

Share Document