Preparation and characteristics of sepiolite-waterborne polyurethane composites

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Tong Xu ◽  
Hong Xu ◽  
Yi Zhong ◽  
Linping Zhang ◽  
Di Qian ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Waterborne Polyurethane ◽  
Elemental Content ◽  
Layer By Layer ◽  
Silane Coupling Agents ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Organically Modified ◽  
Polyurethane Composites

Abstract A kind of organic/inorganic composite material composed of waterborne polyurethane and sepiolite was prepared in this work. Sepiolite was organically modified by three kinds of silane coupling agents, and then compounded with waterborne polyurethane through layer-by-layer method in order to prepare composite materials. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) show the crystal and chemistry structure of sepiolite samples, and confirmed the preparation of organic sepiolite. Scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS) showed the surface microstructure and elemental content of sepiolite and organic sepiolite, and was consistent with the XRD results. Transmission electron microscope (TEM) examination of waterborne polyurethane composites surfaces showed that sepiolite particles were regularly dispersed in the waterborne polyurethane matrix. Thermal resistance of waterborne polyurethane composites was determined by thermogravimetry analyzer (TG) and derivative thermogravimetry analyzer (DTG), differential scanning calorimetry (DSC), gas chromatography (GC), and mass chromatography (MS). Mechanical behavior was examined by tensile strength tester, showed higher break strength than that of the control waterborne polyurethane. Therefore, organically modified sepiolite was considered to be a kind of wonderful inorganic material that could be used to improve the thermal stability and mechanical property of polymer.

scholarly journals Synthesis of BaTiO3 Nanoparticles via Hydrothermal Method

2017 ◽  
Vol 268 ◽  
pp. 172-176 ◽  
Author(s):  
Nurul Norfarina Hasbullah ◽  
Oon Jew Lee ◽  
Josephine Liew Ying Chyi ◽  
Soo Kien Chen ◽  
Zainal Abidin Talib
Keyword(s):  
Electron Microscope ◽  
Hydrothermal Method ◽  
Transmission Electron Microscope ◽  
Hydrothermal Process ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Average Size ◽  
Tga And Dsc

In this work, BaTiO3 nanoparticles were synthesized through hydrothermal method. The powder obtained from the hydrothermal process (as-synthesized powder) was calcined at 1000 °C. The phase formation and morphology of the as-synthesized and calcined powders were studied using X-ray diffraction (XRD), thermogravimetric (TGA) and differential scanning calorimetry (DSC) analyzer, and transmission electron microscope (TEM). The XRD data showed that the as-synthesized powder is partially amorphous. Upon calcining the powder at 1000 °C, highly crystalline BaTiO3 with tetragonal structure was obtained. As shown by TGA and DSC analysis, the precursor powder was completely transformed into BaTiO3 at 1000 °C. The presence of BaCO3 as an impurity phase in the powder is due to the lack of Ba2+ / Ti3+/4+. Transmission electron microscope images showed that the particle size of the as-synthesized powder increased after calcination due to crystal growth. In addition, nanocubes with the average size of around 11.66 nm were obtained as a result of the calcination compared to the ellipsoid like particles of the as-synthesized powder.

A Green Approach for the Synthesis of a Cerium Oxide Nanoparticle: Characterization and Antibacterial Activity

2014 ◽  
Vol 13 (03) ◽  
pp. 1450018 ◽  
Author(s):  
S. K. Kannan ◽  
M. Sundrarajan
Keyword(s):  
Electron Microscope ◽  
Cerium Oxide ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Thermo Gravimetric ◽  
X Ray ◽  
Green Approach ◽  
Transmission Electron ◽  
Ft Ir ◽  
Oxide Nanoparticle

In this study, the synthesis of a cerium oxide nanoparticle was carried out from Acalypha indica leaf extract. The synthesized nanoparticle was characterized by using X-ray diffraction (XRD), Scanning Electron Microscope (SEM), Energy Dispersive X-ray (EDX) and Transmission Electron Microscope (TEM) for structural confirmation. The studies clearly indicate that the synthesized CeO 2 nanoparticle is a crystalline material with particle size between 25–30 nm. Further analysis was carried out by Fourier Transform infrared spectroscopy (FT-IR), to provide evidence for the presence of Ce - O - Ce asymmetry stretching of the CeO 2 nanoparticle. Thermo Gravimetric and Differential Scanning Calorimetry analyses gave the thermal properties of cerium oxide nanoparticles. Antibacterial studies were conducted using the synthesized CeO 2. This result showed increasing rate of antibacterial behavior with gram positive and gram negative bacteria.

scholarly journals Effects of aluminum (Al) incorporation on structural, optical and thermal properties of ZnO nanoparticles

2018 ◽  
Vol 36 (3) ◽  
pp. 419-426
Author(s):  
Nashiruddin Ahammed ◽  
Md Samim Hassan ◽  
Mehedi Hassan
Keyword(s):  
Thermal Properties ◽  
Electron Microscope ◽  
Zno Nanoparticles ◽  
Sol Gel ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Ft Ir ◽  
Doped Zno

AbstractIn this research article, pure and 1 %, 3 % and 5 % aluminium doped zinc oxide nanoparticles (NPs) were prepared via sol-gel method and then calcined at 500 °C. X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transform infrared (FT-IR) spectroscopy, UV-Vis spectroscopy, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques were used to investigate the structural, optical and thermal properties of synthesized pure and Al doped ZnO nanoparticles. Energy dispersive X-ray spectroscopy (EDX) analysis revealed high purity of nanoparticles in the synthesized products without any impurity peaks. Mean dimension of the nanoparticles was ~28 nm and they were hexagonal in shape, according to the images analyzed by transmission electron microscope (TEM). The optical absorption spectra of pure and Al doped ZnO samples studied using UV-Vis spectrometry have been presented and we have observed that the band gap increases with increasing Al concentration. In FT-IR spectra, the broad absorption peaks around 485 cm−1 and 670 cm−1 were assigned to Zn–O vibration. Above 450 °C, the TG curve became flat what means there was no weight loss. In the DSC curve it is seen that the transition at 150 °C was highly exothermic because of structural relaxation and on doping the exothermic peaks became shifted to the lower value of temperature. These types of materials are very useful in optoelectronics applications.

scholarly journals Size Effect on the Structural and Magnetic Properties of Nanosized PerovskiteLaFeO3Prepared by Different Methods

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Nguyen Thi Thuy ◽  
Dang Le Minh
Keyword(s):  
Magnetic Properties ◽  
Electron Microscope ◽  
Room Temperature ◽  
High Energy ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation

Nanosized LaFeO3material was prepared by 3 methods: high energy milling, citrate gel, and coprecipitation. The X-ray diffraction (XRD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) show that the orthorhombic LaFeO3phase was well formed at a low sintering temperature of 500°C in the citrate-gel and co-precipitation methods. Scanning electron microscope (SEM) and transmission electron microscope (TEM) observations indicate that the particle size of the LaFeO3powder varies from 10 nm to 50 nm depending on the preparation method. The magnetic properties through magnetization versus temperatureM(T)and magnetization verses magnetic fieldM(H)characteristics show that the nano-LaFeO3exhibits a weak ferromagnetic behavior in the room temperature, and theM(H)curves are well fitted by Langevin functions.

X-ray microanalysis of thin specimens in the transmission electron microscope at voltages up to 1000 Kv.

1978 ◽  
Vol 36 (1) ◽  
pp. 540-541
Author(s):  
G. Cliff ◽  
M.J. Nasir ◽  
G.W. Lorimer ◽  
N. Ridley
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Weight Fraction ◽  
Present Series ◽  
Constant Independent ◽  
X Ray ◽  
Transmission Electron ◽  
Series Of Experiments ◽  
Image Position ◽  
X Ray Absorption

In a specimen which is transmission thin to 100 kV electrons - a sample in which X-ray absorption is so insignificant that it can be neglected and where fluorescence effects can generally be ignored (1,2) - a ratio of characteristic X-ray intensities, I1/I2 can be converted into a weight fraction ratio, C1/C2, using the equationwhere k12 is, at a given voltage, a constant independent of composition or thickness, k12 values can be determined experimentally from thin standards (3) or calculated (4,6). Both experimental and calculated k12 values have been obtained for K(11<Z>19),kα(Z>19) and some Lα radiation (3,6) at 100 kV. The object of the present series of experiments was to experimentally determine k12 values at voltages between 200 and 1000 kV and to compare these with calculated values.The experiments were carried out on an AEI-EM7 HVEM fitted with an energy dispersive X-ray detector.

Aspects of microanalysis in a transmission electron microscope

1978 ◽  
Vol 36 (1) ◽  
pp. 510-511
Author(s):  
R. Sinclair ◽  
B.E. Jacobson
Keyword(s):  
Grain Size ◽  
Electron Beam ◽  
Electron Microscope ◽  
Chemical Analysis ◽  
Transmission Electron Microscope ◽  
Vapor Deposition ◽  
Critical Currents ◽  
X Ray ◽  
Fine Grain ◽  
Transmission Electron

INTRODUCTIONThe prospect of performing chemical analysis of thin specimens at any desired level of resolution is particularly appealing to the materials scientist. Commercial TEM-based systems are now available which virtually provide this capability. The purpose of this contribution is to illustrate its application to problems which would have been intractable until recently, pointing out some current limitations.X-RAY ANALYSISIn an attempt to fabricate superconducting materials with high critical currents and temperature, thin Nb3Sn films have been prepared by electron beam vapor deposition [1]. Fine-grain size material is desirable which may be achieved by codeposition with small amounts of Al2O3 . Figure 1 shows the STEM microstructure, with large (∽ 200 Å dia) voids present at the grain boundaries. Higher quality TEM micrographs (e.g. fig. 2) reveal the presence of small voids within the grains which are absent in pure Nb3Sn prepared under identical conditions. The X-ray spectrum from large (∽ lμ dia) or small (∽100 Ǻ dia) areas within the grains indicates only small amounts of A1 (fig.3).

Thickness and composition determinations from T.E.M. specimens using both x-ray and backscattered electron data

1984 ◽  
Vol 42 ◽  
pp. 576-577
Author(s):  
M.D. Ball ◽  
H. Lagace ◽  
M.C. Thornton
Keyword(s):  
Electron Microscope ◽  
Atomic Number ◽  
Transmission Electron Microscope ◽  
Convenient Method ◽  
Flow Chart ◽  
X Ray ◽  
Intensity Measurements ◽  
Transmission Electron ◽  
Electron Intensity ◽  
Backscattered Electron

The backscattered electron coefficient η for transmission electron microscope specimens depends on both the atomic number Z and the thickness t. Hence for specimens of known atomic number, the thickness can be determined from backscattered electron coefficient measurements. This work describes a simple and convenient method of estimating the thickness and the corrected composition of areas of uncertain atomic number by combining x-ray microanalysis and backscattered electron intensity measurements.The method is best described in terms of the flow chart shown In Figure 1. Having selected a feature of interest, x-ray microanalysis data is recorded and used to estimate the composition. At this stage thickness corrections for absorption and fluorescence are not performed.

High Spatial Resolution Compositional Analysis at Interfaces

1980 ◽  
Vol 38 ◽  
pp. 356-359
Author(s):  
John B. Vander Sande ◽  
Thomas F. Kelly ◽  
Douglas Imeson
Keyword(s):  
Electron Microscope ◽  
High Spatial Resolution ◽  
Compositional Analysis ◽  
Scanning Transmission Electron Microscope ◽  
Thin Specimen ◽  
X Ray ◽  
Volume Of Interest ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Electron Energy Loss

In the scanning transmission electron microscope (STEM) a fine probe of electrons is scanned across the thin specimen, or the probe is stationarily placed on a volume of interest, and various products of the electron-specimen interaction are then collected and used for image formation or microanalysis. The microanalysis modes usually employed in STEM include, but are not restricted to, energy dispersive X-ray analysis, electron energy loss spectroscopy, and microdiffraction.

Luminescent Properties of Gd2MoO6:Eu3+ Nanophosphor for WLEDs

2021 ◽  
Author(s):  
Yan Chen ◽  
Yuemei Lan ◽  
Dong Wang ◽  
Guoxing Zhang ◽  
Wenlong Peng ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Fluorescence Spectra ◽  
Solvothermal Method ◽  
Luminescent Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

A series of Gd2-xMoO6:xEu3+(x=0.18-0.38) nanophosphors were synthesized by the solvothermal method. The properties of this nanophosphor were characterized by x-ray diffraction (XRD), transmission electron microscope (TEM), fluorescence spectra and diffuse...

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

Sign in / Sign up

Export Citation Format

Share Document