Temperature Effects on Ultimate Bearing Strength of Polymeric Composite Joints

2002 ◽  
Vol 24 (1) ◽  
pp. 17 ◽  
Author(s):  
EA Armanios ◽  
RB Bucinell ◽  
DW Wilson ◽  
WA Counts ◽  
WS Johnson
Keyword(s):  
Temperature Effects ◽  
Polymeric Composite ◽  
Composite Joints ◽  
Bearing Strength

scholarly journals A Novel Manufacturing Technique to Improve Bearing Strength of Pin Loaded Woven Composites

2011 ◽  
Vol 20 (3) ◽  
pp. 096369351102000 ◽  
Author(s):  
Ercan Sevkat ◽  
Malek Brahimi ◽  
Sidi Berri
Keyword(s):  
Failure Modes ◽  
Hole Diameter ◽  
Woven Composites ◽  
Sustained Load ◽  
Hole Drilling ◽  
Geometrical Parameters ◽  
Composite Joints ◽  
Bearing Strength ◽  
Manufacturing Technique ◽  
Glass Fibre Reinforced

The bearing strength of pin-loaded woven glass-fibre reinforced epoxy composites was investigated. As an alternative to the hole-drilling procedure, a novel composite manufacturing technique has been implemented for pin-hole creation. The bearing performance of composite joints manufactured using both techniques was compared. Specimen with various edge- distances to pin-hole diameter ratios (e/d) and, width to pin-hole diameter ratios (w/d) were tested. It was observed that composite joints manufactured using the novel technique sustained more load compared to the joints manufactured by the hole-drilling procedure. Geometrical parameters were found to be effective on failure modes, bearing strength and magnitude of sustained load.

Bearing Strength of Concrete Column and Steel Beam Composite Joints

2003 ◽  
Vol 15 (3) ◽  
pp. 417-424
Author(s):  
Byong-Kook Kim ◽  
Won-Kyu Lee ◽  
Oan-Chul Choi
Keyword(s):  
Steel Beam ◽  
Concrete Column ◽  
Composite Joints ◽  
Bearing Strength

Cure temperature effects on cryogenic microcracking of polymeric composite materials

2003 ◽  
Vol 24 (1) ◽  
pp. 132-139 ◽  
Author(s):  
John F. Timmerman ◽  
Brian S. Hayes ◽  
James C. Seferis
Keyword(s):  
Composite Materials ◽  
Temperature Effects ◽  
Polymeric Composite ◽  
Polymeric Composite Materials ◽  
Cure Temperature

Characterization of carbides in M50NiL

1991 ◽  
Vol 49 ◽  
pp. 606-607
Author(s):  
L. S. Lin ◽  
K. P. Gumz ◽  
A. V. Karg ◽  
C. C. Law
Keyword(s):  
Temperature Effects ◽  
Base Composition ◽  
Lattice Parameter ◽  
Control Surface ◽  
Carbide Formation ◽  
Particle Sizes ◽  
Low Carbon ◽  
Fee Structure ◽  
Heat Treated

Carbon and temperature effects on carbide formation in the carburized zone of M50NiL are of great importance because they can be used to control surface properties of bearings. A series of homogeneous alloys (with M50NiL as base composition) containing various levels of carbon in the range of 0.15% to 1.5% (in wt.%) and heat treated at temperatures between 650°C to 1100°C were selected for characterizations. Eleven samples were chosen for carbide characterization and chemical analysis and their identifications are listed in Table 1.Five different carbides consisting of M6C, M2C, M7C3 and M23C6 were found in all eleven samples examined as shown in Table 1. M6C carbides (with least carbon) were found to be the major carbide in low carbon alloys (<0.3% C) and their amounts decreased as the carbon content increased. In sample C (0.3% C), most particles (95%) encountered were M6C carbide with a particle sizes range between 0.05 to 0.25 um. The M6C carbide are enriched in both Mo and Fe and have a fee structure with lattice parameter a=1.105 nm (Figure 1).

Sign in / Sign up

Export Citation Format

Share Document