carbide formation
Recently Published Documents


TOTAL DOCUMENTS

315
(FIVE YEARS 49)

H-INDEX

29
(FIVE YEARS 2)

2021 ◽  
Author(s):  
Shahid Hussain ABRO ◽  
Alidad CHANDIO ◽  
Asif Ahmed SHAIKH ◽  
Norbaizura NORDIN ◽  
Hamza SUHARWARDI

An attempt has been made in the present research work to investigate the role and influence of chemical effect of aluminum addition in the experimental steel towards the formation of k-carbides. Two steel grades were made with and without aluminum addition by induction melting furnace and were cast to ingots. Steel A has no aluminum addition and steel B has some aluminum content. These ingots were then solution heat treated on a temperature of 1200°C for 2-hours’ time and were cooled in the air. After that, they were hot rolled to drawn in plate and sheet. The small samples were cut from bulk and were then heat-treated at 800°C for 1 hour and quenched. Microstructure by OM and SEM was captured. In steel A there was no k-carbide present in the matrix and surprisingly in steel B, small fine k-carbides were present this was then confirmed by XRD later. OM, SEM, and TEM analysis revealed that the presence of k-carbides in steel B makes less dense. It was concluded that aluminum in conjunction with nitrogen forms the small nitride particles having a high melting point does not dissolve during the melting and casting such particles are known as AlN or aluminum nitride particles was observed by TEM along with EDS was the main reason to support the formation of k-carbides, these fine nano level k-carbides are orderly distributed in the steel matrix as was shown by XRD peaks.


2021 ◽  
Vol 2064 (1) ◽  
pp. 012055
Author(s):  
G K Zhanbolatova ◽  
V V Baklanov ◽  
M K Skakov ◽  
I A Sokolov ◽  
O S Bukina ◽  
...  

Abstract This paper presents a method of tungsten surface carbidization using a plasma-beam setup to assess the effect of temperature on the formation of tungsten carbides. Methane was used as a plasma-forming gas. The working gas pressure in the chamber was (1.3–1.4)10−1 Pa. Experiments on the formation of carbides were carried out at different temperatures (700-1000°C). It was recorded that at a temperature of 700°C, crystallization centers of a carbon film appear on the sample surface. With an increase in the irradiation temperature to 800°C and 900°C, the surface of the samples is covered with a continuous carbon film. As a result of the experimental work carried out, it was found that the formation of tungsten semicarbide occurs at 900°C. A further increase in temperature leads to the formation of tungsten monocarbide.


Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5796
Author(s):  
Larissa Moravcikova-Gouvea ◽  
Igor Moravcik ◽  
Vaclav Pouchly ◽  
Zuzana Kovacova ◽  
Michael Kitzmantel ◽  
...  

This paper reports the microstructural evolution and mechanical properties of a low-density Al0.3NbTa0.8Ti1.5V0.2Zr refractory high-entropy alloy (RHEA) prepared by means of a combination of mechanical alloying and spark plasma sintering (SPS). Prior to sintering, the morphology, chemical homogeneity and crystal structures of the powders were thoroughly investigated by varying the milling times to find optimal conditions for densification. The sintered bulk RHEAs were produced with diverse feedstock powder conditions. The microstructural development of the materials was analyzed in terms of phase composition and constitution, chemical homogeneity, and crystallographic properties. Hardness and elastic constants also were measured. The calculation of phase diagrams (CALPHAD) was performed to predict the phase changes in the alloy, and the results were compared with the experiments. Milling time seems to play a significant role in the contamination level of the sintered materials. Even though a protective atmosphere was used in the entire manufacturing process, carbide formation was detected in the sintered bulks as early as after 3 h of powder milling. Oxides were observed after 30 h due to wear of the high-carbon steel milling media and SPS consolidation. Ten hours of milling seems sufficient for achieving an optimal equilibrium between microstructural homogeneity and refinement, high hardness and minimal contamination.


2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Guoliang Ma ◽  
Hui Shao ◽  
Jin Xu ◽  
Ying Liu ◽  
Qing Huang ◽  
...  

AbstractStructural bidimensional transition-metal carbides and/or nitrides (MXenes) have drawn the attention of the material science research community thanks to their unique physical-chemical properties. However, a facile and cost-effective synthesis of MXenes has not yet been reported. Here, using elemental precursors, we report a method for MXene synthesis via titanium aluminium carbide formation and subsequent in situ etching in one molten salt pot. The molten salts act as the reaction medium and prevent the oxidation of the reactants during the high-temperature synthesis process, thus enabling the synthesis of MXenes in an air environment without using inert gas protection. Cl-terminated Ti3C2Tx and Ti2CTx MXenes are prepared using this one-pot synthetic method, where the in situ etching step at 700 °C requires only approximately 10 mins. Furthermore, when used as an active material for nonaqueous Li-ion storage in a half-cell configuration, the obtained Ti2CTx MXene exhibits lithiation capacity values of approximately 280 mAh g−1 and 160 mAh g−1 at specific currents of 0.1 A g−1 and 2 A g−1, respectively.


Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3849
Author(s):  
Ernst Plesiutschnig ◽  
Mihaela Albu ◽  
David Canelo-Yubero ◽  
Vsevolod I. Razumovskiy ◽  
Andreas Stark ◽  
...  

Precipitation hardened and tempered martensitic-ferritic steels (TMFSs) are used in many areas of our daily lives as tools, components in power generation industries, or in the oil and gas (O&G) industry for creep and corrosion resistance. In addition to the metallurgical and forging processes, the unique properties of the materials in service are determined by the quality heat treatment (HT). By performing a quenching and partitioning HT during an in situ high energy synchrotron radiation experiment in a dilatometer, the evolution of retained austenite, martensite laths, dislocations, and carbides was characterized in detail. Atomic-scale studies on a specimen with the same HT subjected to a laser scanning confocal microscope show how dislocations facilitate cloud formation around carbides. These clouds have a discrete build-up, and thermodynamic calculations and density functional theory explain their stability.


Catalysts ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 773
Author(s):  
Aleks Arinchtein ◽  
Meng-Yang Ye ◽  
Michael Geske ◽  
Marvin Frisch ◽  
Ralph Kraehnert

CO2 Fischer–Tropsch synthesis (CO2–FTS) is a promising technology enabling conversion of CO2 into valuable chemical feedstocks via hydrogenation. Iron–based CO2–FTS catalysts are known for their high activities and selectivities towards the formation of higher hydrocarbons. Importantly, iron carbides are the presumed active phase strongly associated with the formation of higher hydrocarbons. Yet, many factors such as reaction temperature, atmosphere, and pressure can lead to complex transformations between different oxide and/or carbide phases, which, in turn, alter selectivity. Thus, understanding the mechanism and kinetics of carbide formation remains challenging. We propose model–type iron oxide films of controlled nanostructure and phase composition as model materials to study carbide formation in syngas atmospheres. In the present work, different iron oxide precursor films with controlled phase composition (hematite, ferrihydrite, maghemite, maghemite/magnetite) and ordered mesoporosity are synthesized using the evaporation–induced self–assembly (EISA) approach. The model materials are then exposed to a controlled atmosphere of CO/H2 at 300 °C. Physicochemical analysis of the treated materials indicates that all oxides convert into carbides with a core–shell structure. The structure appears to consist of crystalline carbide cores surrounded by a partially oxidized carbide shell of low crystallinity. Larger crystallites in the original iron oxide result in larger carbide cores. The presented simple route for the synthesis and analysis of soft–templated iron carbide films will enable the elucidation of the dynamics of the oxide to carbide transformation in future work.


2021 ◽  
Vol 1035 ◽  
pp. 925-930
Author(s):  
Ya Zhou Li ◽  
Yu Zhao ◽  
Xu Ran

To reduce the agglomeration of graphene and enhance the interface bonding between reduced graphene oxide (RGO) and copper substrate, copper plating on the graphene surface was prepared by the in-situ reduction method. To improve the strength of the copper matrix, the microalloying strategy of adding titanium to the matrix was adopted. By changing the mass fraction of titanium in the matrix, the optimum ratio of RGO was obtained( Ti mass fraction was 5:1), and the tensile strength was maximized. The results show that RGO did not agglomerate obviously in the matrix. At the same time, the composite powder could be densified rapidly by spark plasma sintering (SPS), which could effectively protect the original distribution of the additive phase in the matrix. In this paper, Cu@RGO/Cu-Ti was prepared and the strengthening mechanism of the composites discussed, providing a new insights into the interface design and carbide formation mechanism of advanced graphene/copper composites with high mechanical properties.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Chatdanai Boonruang ◽  
Wutipong Sanumang

AbstractThe effect of low oxygen-partial pressured carburizing on relaxation process for 316L stainless steel is reported. Phase, morphology, and amount of compound formation during initial stage of carburizing are investigated using X-ray diffractometry (XRD) and X-ray photoelectron spectroscopy (XPS). The results show formation and development of surface multilayer with nano-grain-carbide (Cr7C3, Fe7C3, and/or Cr3C2) generation in the layer located below outermost protective layer. The relaxation process has been investigated using electrochemical impedance spectroscopy (EIS). Formation of nano-grain carbide(s) during carburizing causes deterioration effect on the electrochemical behavior of steel. However, the steel with large amount of carbide generation (carburized for 30 min) tends to have higher corrosion resistance (indicated by higher values of Rcl and Rct) than the smaller ones (10 and 20 min) due to the effect of phase, grain size, morphology, and amount of compound formation.


2021 ◽  
Vol 397 ◽  
pp. 1-12
Author(s):  
Paul Hazemann ◽  
Dominique Decottignies ◽  
Sylvie Maury ◽  
Séverine Humbert ◽  
Frederic C. Meunier ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document