pH Dependence of the Aqueous Dissolution Rates of Perovskite and Zirconolite at 90°C

1994 ◽  
Vol 353 ◽  
Author(s):  
Peter J McGlinn ◽  
K. P. Hart ◽  
E. H. Loi ◽  
E. R. Vance
Keyword(s):  
Mineral Assemblage ◽  
Perovskite Phase ◽  
Ph Dependence ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dissolution Behaviour ◽  
Alkaline Conditions ◽  
Ph Conditions ◽  
Sem Investigation

AbstractPerovskite and zirconolite are two of the major phases of the Synroc titanate mineral assemblage. Their aqueous durability under a range of pH conditions at 90°C has been examined. Solution analysis, electron microscopy and X-ray diffraction have been used to investigate the dissolution behaviour of these phases, and a perovskite phase doped with Nd, Sr and Al, using buffered solutions at pH levels of 2.1, 3.7, 6.1, 7.9 and 12.9. After 43 days of leaching, Ca and Ti extractions from perovskite and zirconolite show only a weak pH-dependence.SEM investigation of the samples leached at pH 2.1, 6.1 and 12.9 showed that a titanaceous surface layer formed on the perovskite specimens. XRD analysis of the perovskite samples showed that anatase formed on the leached surface at acidic and neutral pHs, but not under alkaline conditions, and that minor amounts of rutile also formed. In the leached perovskite specimens doped with Nd, Sr and Al, no rutile was found by XRD and anatase was only detected in the sample leached at pH 2.1. There were no detectable changes in the leached zirconolite samples examined by SEM and XRD.

Transformation of magnetite to goethite under alkaline pH conditions

Clay Minerals ◽  
2007 ◽  
Vol 42 (1) ◽  
pp. 13-19 ◽  
Author(s):  
Y. T. He ◽  
S. J. Traina
Keyword(s):  
X Ray Diffraction ◽  
Hanford Site ◽  
X Ray ◽  
Sedimentary Environments ◽  
Waste Storage ◽  
Transmission Electron ◽  
Redox Active ◽  
Alkaline Conditions ◽  
Ph Conditions ◽  
High Level

AbstractMagnetite is a redox active Fe oxide common in most soil and sedimentary environments. In this study, we investigated magnetite transformations under extreme alkaline conditions (0.1–2 mol l–1 NaOH) similar to those found under high-level radioactive waste storage tanks at the Hanford site in the State of Washington, USA. X-ray diffraction (XRD) and transmission electron microscopy (TEM) results showed that magnetite was transformed into maghemite and goethite, and the XRD peak intensities for goethite increased with NaOH concentration. Goethite was presumably formed through reconstructive dissolution/crystallization reactions that can be written as: Fe3O4 + OH– + H2O = γ-Fe2O3 + Fe(OH)3–; 2Fe(OH)3– + 1/2O2 + 2H+ = 2α-FeOOH + 3H2O. Some of the newly formed maghemite may also redissolve to form goethite at greater NaOH concentrations.

scholarly journals IMPEDANCE SPECTROSCOPY AND AC CONDUCTIVITY STUDIES OF FERROELECTRIC (K0.5Na0.5)NbO3 CERAMICS

2011 ◽  
Vol 01 (03) ◽  
pp. 351-356 ◽  
Author(s):  
P. PALEI ◽  
P. KUMAR
Keyword(s):  
Ac Conductivity ◽  
Single Phase ◽  
Perovskite Phase ◽  
Impedance Analysis ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Reaction Route ◽  
Conventional Solid State Reaction ◽  
X Ray ◽  
Higher Temperature

Lead free (K0.5Na0.5)NbO3 (KNN) ceramics were prepared by conventional solid state reaction route. For single perovskite phase formation, calcination temperature was optimized at 850°C for 6 h, whereas for dense morphology the sintering of the ceramic was carried out at 1120°C for 4 h. X-ray diffraction XRD analysis confirmed the formation of single phase with orthorhombic structure at room temperature. Impedance analysis and AC conductivity studies of the KNN sample was carried out in the temperature range of 703–773 K. Impedance study showed the increase in conducting behavior at higher temperature. The temperature dependence of AC conductivity indicated that the conduction process is due to doubly ionized oxygen vacancies in the higher temperature region.

Identification of acid-insoluble filter-plugging compounds and optimal acid-washing procedures for tubular backpulse pressure filters

TAPPI Journal ◽  
2011 ◽  
Vol 10 (1) ◽  
pp. 17-23
Author(s):  
KEVIN TAYLOR ◽  
RICH ADDERLY ◽  
GAVIN BAXTER
Keyword(s):  
Calcium Sulfate ◽  
Membrane Filter ◽  
Sulfamic Acid ◽  
Xrd Analysis ◽  
Metal Sulfides ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gypsum Formation ◽  
Acid Washing ◽  
Hydrolysis Of

Over time, performance of tubular backpulse pressure filters in kraft mills deteriorates, even with regular acid washing. Unscheduled filter replacement due to filter plugging results in significant costs and may result in mill downtime. We identified acid-insoluble filter-plugging materials by scanning electron microscope/energy-dispersion X-ray spectroscopy (SEM/EDS) and X-ray diffraction (XRD) analysis in both polypropylene and Gore-Tex™ membrane filter socks. The major filter-plugging components were calcium sulfate (gypsum), calcium phosphate (hydroxylapatite), aluminosilicate clays, metal sulfides, and carbon. We carried out detailed sample analysis of both the standard acid-washing procedure and a modified procedure. Filter plugging by gypsum and metal sulfides appeared to occur because of the acid-washing procedure. Gypsum formation on the filter resulted from significant hydrolysis of sulfamic acid solution at temperatures greater than 130°F. Modification of the acid-washing procedure greatly reduced the amount of gypsum and addition of a surfactant to the acid reduced wash time and mobilized some of the carbon from the filter. With surfactant, acid washing was 95% complete after 40 min.

A study on using expanded perlite with hydroxyapatite: Reinforced bio-composites

2021 ◽  
pp. 095441192199656
Author(s):  
Erdoğan Karip ◽  
Mehtap Muratoğlu
Keyword(s):  
Body Fluid ◽  
Xrd Analysis ◽  
Cold Isostatic Pressing ◽  
Expanded Perlite ◽  
X Ray Diffraction ◽  
Pressing Method ◽  
X Ray ◽  
Infra Red ◽  
Ft Ir

People are exposed to different kinds of diseases or various accidents in life. Hydroxyapatite (HA) has been widely employed for bone treatment applications. In this study, HA was extracted from sheep bones. Bio-composites were doped with 1, 5, and 10 wt.% of expanded perlite and 5 wt.% of ZrO2–MgO-P2O5. The bio-composites were prepared by the cold isostatic pressing method (250 MPa) and sintered at 900°C for 1 h. In order to evaluate the characteristics of the bio-composites, microhardness, density, X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FT-IR), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) analyses were carried out on them. Additionally, the specimens whose characteristics were determined were kept in synthetic body fluid (SBF), and their in vitro behavior was examined. As a result, it was observed that microhardness increased as both the weight and the grain size of the expanded perlite were increased. Calcium silicate, tri-calcium phosphate, and hydroxyapatite were observed in the XRD analysis of all samples, and the formation of apatite structures was increased by addition of ZrO2–MgO–P2O5.

scholarly journals An Insight into Chemistry and Structure of Colloidal 2D-WS2 Nanoflakes: Combined XPS and XRD Study

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1969
Author(s):  
Riccardo Scarfiello ◽  
Elisabetta Mazzotta ◽  
Davide Altamura ◽  
Concetta Nobile ◽  
Rosanna Mastria ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Xrd Analysis ◽  
Crystal Habit ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Evaluation ◽  
Rational Understanding ◽  
Structural Inspection

The surface and structural characterization techniques of three atom-thick bi-dimensional 2D-WS2 colloidal nanocrystals cross the limit of bulk investigation, offering the possibility of simultaneous phase identification, structural-to-morphological evaluation, and surface chemical description. In the present study, we report a rational understanding based on X-ray photoelectron spectroscopy (XPS) and structural inspection of two kinds of dimensionally controllable 2D-WS2 colloidal nanoflakes (NFLs) generated with a surfactant assisted non-hydrolytic route. The qualitative and quantitative determination of 1T’ and 2H phases based on W 4f XPS signal components, together with the presence of two kinds of sulfur ions, S22− and S2−, based on S 2p signal and related to the formation of WS2 and WOxSy in a mixed oxygen-sulfur environment, are carefully reported and discussed for both nanocrystals breeds. The XPS results are used as an input for detailed X-ray Diffraction (XRD) analysis allowing for a clear discrimination of NFLs crystal habit, and an estimation of the exact number of atomic monolayers composing the 2D-WS2 nanocrystalline samples.

scholarly journals Effect of Molybdenum Content on the Corrosion and Microstructure of Low-Ni, Co-Free Maraging Steels

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 852
Author(s):  
Asiful H. Seikh ◽  
Hossam Halfa ◽  
Mahmoud S. Soliman
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Microstructural Analysis ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Alloying Element ◽  
X Ray ◽  
Maraging Steels ◽  
Eds Analysis ◽  
Electroslag Refining

Molybdenum (Mo) is an important alloying element in maraging steels. In this study, we altered the Mo concentration during the production of four cobalt-free maraging steels using an electroslag refining process. The microstructure of the four forged maraging steels was evaluated to examine phase contents by optical microscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. Additionally, we assessed the corrosion resistance of the newly developed alloys in 3.5% NaCl solution and 1 M H2SO4 solution through potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Furthermore, we performed SEM and energy-dispersive spectroscopy (EDS) analysis after corrosion to assess changes in microstructure and Raman spectroscopy to identify the presence of phases on the electrode surface. The microstructural analysis shows that the formation of retained austenite increases with increasing Mo concentrations. It is found from corrosion study that increasing Mo concentration up to 4.6% increased the corrosion resistance of the steel. However, further increase in Mo concentration reduces the corrosion resistance.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

THE SOLIDIFICATION MICROSTRUCTURE OF BIOMEDICAL TITANIUM ALLOYS UNDER THE CENTRIFUGAL FORCE

2006 ◽  
Vol 20 (25n27) ◽  
pp. 4685-4690
Author(s):  
ZIYONG CHEN ◽  
LIJUAN XU ◽  
ZHIGUANG LIU ◽  
YUYONG CHEN
Keyword(s):  
Centrifugal Force ◽  
Graphite Crucible ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Crystal Boundary ◽  
X Ray ◽  
Solidification Defects ◽  
Solidification Microstructures ◽  
Centrifugal Equipment ◽  
Graphite Mould

Two biomedical alloys, Ti -39 Nb -5.1 Ta -7.1 Zr ( TNTZ1 ) and Ti -35.3 Nb -5.1 Ta -7.1 Zr ( TNTZ2 ) were melted using LZ5 type centrifugal equipment for casting titanium. The solidification microstructures of TNTZ1 and TNTZ2 alloys cast in graphite crucible without centrifugal force are mostly big arborescent crystal with dispersed porosity in it. After pouring into a graphite mould under centrifugal force, the lower part of ingot showed mostly arborescent crystals with few equiaxed crystals, while the upper part of ingot is basically spherical equiaxed crystals. The solidification defects, such as dispersed pores were very difficult to find. Nb is supposed to refine the arborescent crystals. X-ray diffraction (XRD) analysis showed Ti -phase and Nb -phase existing in the above two alloys. The content of Ti was found relatively low in crystal interior and relatively high in crystal boundary. The content of Nb/Zr was uniform in whole microstructure.

Influence of High Current Pulsed Electron Beam Irradiation on Ni-P Electroless Plating

2011 ◽  
Vol 299-300 ◽  
pp. 77-81
Author(s):  
Yang Xu ◽  
Sheng Zhi Hao ◽  
Xiang Dong Zhang ◽  
Min Cai Li ◽  
Chuang Dong
Keyword(s):  
Electroless Plating ◽  
Electron Beam Irradiation ◽  
Xrd Analysis ◽  
High Current ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pulsed Electron Beam ◽  
6063 Aluminum Alloy ◽  
Pre Treatment ◽  
Better Than

The surface irradiation of 6063 aluminum alloy by high current pulsed electron was conducted with the aim of replacing the complicated pre-treatment in the processes of electroless plating. To explore the microstructure changes, optical metallography, SEM (scanning electron microscope), XRD (X-ray diffraction) analyses were carried out, and the sliding tests were used for the detection of wear resistance. It was concluded that the HCPEB irradiation could replace the pre-treatment of aluminum substrate as required in conventional electroless plating with a decreased surface roughness of Ni-P alloy plating layer. The plates exhibited an amorphous microstructure as demonstrated by XRD analysis. The plates, produced with the routine of HCPEB irradiation, activation and electroless plating possess, also exhibited good quality, even better than that of conventional electroless plating technique.

Sign in / Sign up

Export Citation Format

Share Document