Application of shearwave™ elastography to evaluate heat-induced changes in the young's modulus of fresh bovine muscle: A preliminary study

2021 ◽  
Author(s):  
José Francisco Silva Costa Júnior ◽  
Viviane Bastos Oliveira ◽  
Lucas Lobianco De Matheo ◽  
Wagner Coelho Pereira
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Therapeutic Ultrasound ◽  
Region Of Interest ◽  
Application Time ◽  
Muscle Sample ◽  
Experimental Procedure ◽  
Bovine Muscle ◽  
Induced Changes ◽  
Therapeutic Irradiation

Abstract PurposeThe purpose of this study was to investigate the variation in the Young’s modulus (E) of bovine muscle samples as a function of temperature change generated by therapeutic ultrasound using Shearwave™ Elastography.MethodsInitially, the bovine muscle was heated via therapeutic ultrasound with a frequency of 3 MHz, nominal intensity of 2 W·cm-2, and application time of 2 min. Immediately following cessation of therapeutic irradiation, an E image was recorded and the stiffness was measured in circular area positioned at six depths (from 0.4 to 2.9 cm) in the center of the region of interest. Next, an E image was recorded every minute for the first 5 min. Over the next 30 min, an image was recorded every 5 min. Finally, an image was acquired 60 min after cessation of therapeutic irradiation. In the second test, the same experimental procedure was performed 60 min later with the physiotherapy equipment configured with a 10-min application time. Finally, during the ultrasonic irradiation of a new bovine muscle sample, the physiotherapeutic transducer was applied in a circular motion and with an angular velocity of 3.6 ± 0.3 rad·s-1.ResultsIn the first test, the bovine muscle E decreased from 212.2 ± 32.8 to 80.1 ± 13.8 kPa at 0.4 cm-depth, as the temperature increased from 18.2 to 44.9 °C. This effect was reversed when the temperature decreased. In the second test, denaturation and cell death occurred, so an artifact appeared in the elastographic image and the Shearwave™ Elastography did not capture the E from the depth of 1.9 cm.ConclusionWe confirmed that it is possible to use Shearwave™ Elastography to investigate heat-induced changes in the elastic modulus of biological tissue.

Application of ShearWave™ Elastography to evaluate heat-induced changes in the Young’s modulus of fresh bovine muscle: a preliminary study

2021 ◽  
Author(s):  
José Francisco Silva Costa-Júnior ◽  
Viviane Bastos de Oliveira ◽  
Lucas Lobianco De Matheo ◽  
Wagner Coelho de Albuquerque Pereira
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Bovine Muscle ◽  
Preliminary Study ◽  
Induced Changes

Evaluation of radiation-induced changes in the Young's modulus of electroceramic materials

1990 ◽  
Vol 47 (2) ◽  
pp. 57-59
Author(s):  
V. L. Ul'yanov ◽  
�. V. Pozdeeva
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Radiation Induced ◽  
Induced Changes

The current-induced changes of resistivity and Young's modulus in the charge ordered La0.25Ca0.75MnO3 manganite

2005 ◽  
Vol 364 (1-4) ◽  
pp. 93-98
Author(s):  
G.H. Zheng ◽  
Y.Q. Ma ◽  
W.J. Lu ◽  
W.H. Song ◽  
J.J. Du ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Induced Changes

scholarly journals Exploring Nanomechanical Properties of Soot Particle Layers by Atomic Force Microscopy Nanoindentation

2021 ◽  
Vol 11 (18) ◽  
pp. 8448
Author(s):  
Gianluigi De Falco ◽  
Fiorenzo Carbone ◽  
Mario Commodo ◽  
Patrizia Minutolo ◽  
Andrea D’Anna
Keyword(s):  
Atomic Force Microscopy ◽  
Young’S Modulus ◽  
Soot Particle ◽  
Young's Modulus ◽  
Contact Mode ◽  
Carbonaceous Particle ◽  
Experimental Procedure ◽  
Force Microscopy ◽  
Nanomechanical Properties ◽  
Atomic Force

In this work, an experimental investigation of the nanomechanical properties of flame-formed carbonaceous particle layers has been performed for the first time by means of Atomic Force Microscopy (AFM). To this aim, carbon nanoparticles with different properties and nanostructures were produced in ethylene/air laminar premixed flames at different residence times. Particles were collected on mica substrates by means of a thermophoretic sampling system and then analyzed by AFM. An experimental procedure based on the combination between semi-contact AFM topography imaging, contact AFM topography imaging and AFM force spectroscopy has been implemented. More specifically, a preliminary topological characterization of the samples was first performed operating AFM in semi-contact mode and then tip-sample interaction forces were measured in contact spectroscopy mode. Finally, semi-contact mode was used to image the indented surface of the samples and to retrieve the projected area of indents. The hardness of investigated samples was obtained from the force–distance curves measured in spectroscopy mode and the images of intends acquired in semi-contact mode. Moreover, the Young’s modulus was measured by fitting the linear part of the retraction force curves using a model based on the Hertz theory. The extreme force sensitivity of this technique (down to nNewton) in addition to the small size of the probe makes it extremely suitable for performing investigation of mechanical properties of materials at the nanoscale. The experimental procedure was successfully tested on reference materials characterized by different plastic behavior, e.g., polyethylene naphthalate and highly oriented pyrolytic graphite. Both hardness and Young’s modulus values obtained from AFM measurements for different soot particle films were discussed.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

Degradation of Rocks, Through Cracking Caused by Differential Thermal Expansion, in Relation to Nuclear Waste Repositories

1981 ◽  
Vol 6 ◽  
Author(s):  
J.R. Mclaren ◽  
R.W. Davidge ◽  
I. Titchell ◽  
K. Sincock ◽  
A. Bromley
Keyword(s):  
Thermal Expansion ◽  
Grain Boundary ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Crack Density ◽  
Granitic Rocks ◽  
Multiphase Materials ◽  
Thermal Expansion Behaviour ◽  
Waste Repositories ◽  
Expansion Behaviour

ABSTRACTHeating to temperatures up to 500°C, gives a reduction in Young's modulus and increase in permeability of granitic rocks and it is likely that a major reason is grain boundary cracking. The cracking of grain boundary facets in polycrystalline multiphase materials showing anisotropic thermal expansion behaviour is controlled by several microstructural factors in addition to the intrinsic thermal and elastic properties. Of specific interest are the relative orientations of the two grains meeting at the facet, and the size of the facet; these factors thus introduce two statistical aspects to the problem and these are introduced to give quantitative data on crack density versus temperature. The theory is compared with experimental measurements of Young's modulus and permeability for various rocks as a function of temperature. There is good qualitative agreement, and the additional (mainly microstructural) data required for a quantitative comparison are defined.

Is it necessary to calculate Young’s modulus in AFM nanoindentation experiments regarding biological samples?

2020 ◽  
Vol 12 ◽  
Author(s):  
S.V. Kontomaris ◽  
A. Malamou ◽  
A. Stylianou
Keyword(s):  
Young’S Modulus ◽  
Biological Samples ◽  
Young's Modulus ◽  
Reference Sample ◽  
Nonlinear Behavior ◽  
Accurate Method ◽  
Accurate Solution ◽  
Hertz Model ◽  
Work Done

Background: The determination of the mechanical properties of biological samples using Atomic Force Microscopy (AFM) at the nanoscale is usually performed using basic models arising from the contact mechanics theory. In particular, the Hertz model is the most frequently used theoretical tool for data processing. However, the Hertz model requires several assumptions such as homogeneous and isotropic samples and indenters with perfectly spherical or conical shapes. As it is widely known, none of these requirements are 100 % fulfilled for the case of indentation experiments at the nanoscale. As a result, significant errors arise in the Young’s modulus calculation. At the same time, an analytical model that could account complexities of soft biomaterials, such as nonlinear behavior, anisotropy, and heterogeneity, may be far-reaching. In addition, this hypothetical model would be ‘too difficult’ to be applied in real clinical activities since it would require very heavy workload and highly specialized personnel. Objective: In this paper a simple solution is provided to the aforementioned dead-end. A new approach is introduced in order to provide a simple and accurate method for the mechanical characterization at the nanoscale. Method: The ratio of the work done by the indenter on the sample of interest to the work done by the indenter on a reference sample is introduced as a new physical quantity that does not require homogeneous, isotropic samples or perfect indenters. Results: The proposed approach, not only provides an accurate solution from a physical perspective but also a simpler solution which does not require activities such as the determination of the cantilever’s spring constant and the dimensions of the AFM tip. Conclusion: The proposed, by this opinion paper, solution aims to provide a significant opportunity to overcome the existing limitations provided by Hertzian mechanics and apply AFM techniques in real clinical activities.

Effect of Microcrystalline Cellulose from Banana Stem Fiber on Mechanical Properties and Crystallinity of PLA Composite Films

2011 ◽  
Vol 695 ◽  
pp. 170-173 ◽  
Author(s):  
Voravadee Suchaiya ◽  
Duangdao Aht-Ong
Keyword(s):  
Tensile Strength ◽  
Young’S Modulus ◽  
Microcrystalline Cellulose ◽  
Young's Modulus ◽  
Agricultural Waste ◽  
Composite Films ◽  
Sem Image ◽  
Biocomposite Films ◽  
Twin Screw ◽  
Banana Stem

This work focused on the preparation of the biocomposite films of polylactic acid (PLA) reinforced with microcrystalline cellulose (MCC) prepared from agricultural waste, banana stem fiber, and commercial microcrystalline cellulose, Avicel PH 101. Banana stem microcrystalline cellulose (BS MCC) was prepared by three steps, delignification, bleaching, and acid hydrolysis. PLA and two types of MCC were processed using twin screw extruder and fabricated into film by a compression molding. The mechanical and crystalline behaviors of the biocomopsite films were investigated as a function of type and amount of MCC. The tensile strength and Young’s modulus of PLA composites were increased when concentration of MCC increased. Particularly, banana stem (BS MCC) can enhance tensile strength and Young’s modulus of PLA composites than the commercial MCC (Avicel PH 101) because BS MCC had better dispersion in PLA matrix than Avicel PH 101. This result was confirmed by SEM image of fractured surface of PLA composites. In addition, XRD patterns of BS MCC/PLA composites exhibited higher crystalline peak than that of Avicel PH 101/PLA composites

Sign in / Sign up

Export Citation Format

Share Document