The Effect of Temperature and Water Film Thickness on the Linear Instability of an Ice Surface

2013 ◽  
Author(s):  
Alric P. Rothmayer ◽  
Hui Hu
Keyword(s):  
Film Thickness ◽  
Water Film ◽  
Linear Instability ◽  
Effect Of Temperature ◽  
Water Film Thickness ◽  
Ice Surface

Influence of Ground Slag on the Rheology of Mortar

2013 ◽  
Vol 438-439 ◽  
pp. 67-71
Author(s):  
Qian Qian Zhang ◽  
Jian Zhong Liu ◽  
Jia Ping Liu
Keyword(s):  
Film Thickness ◽  
Specific Surface ◽  
Yield Stress ◽  
Surface Area ◽  
Specific Surface Area ◽  
Water Film ◽  
Plastic Viscosity ◽  
Rheological Parameters ◽  
Water Film Thickness ◽  
Binder Ratio

The effects of ground slag with different specific surface area on the rheology of mortar at water-binder ratio of 0.25, 0.28 and 0.30 were investigated, and the combined effects of packing density and solid surface area on the rheology of mortar were evaluated in terms of the water film thickness. The results show that with the increasing of specific surface area of slag (220 m2/kg-784 m2/kg), plastic viscosity and yield stress decrease. The correlations of yield stress and plastic viscosity to the water film thickness are basically linear with high correlation R2 values. The action of the ground slag on the rheology of mortar can be characterized by water film thickness, and with the increasing of water film thickness the rheological parameters decrease.

Measuring Water Film Thickness in a Wet Gas Compressor Diffuser: Design, Calibration, and Testing of Electromagnetic Probes

2017 ◽  
Author(s):  
Craig Nolen ◽  
Melissa Poerner
Keyword(s):  
Film Thickness ◽  
Water Level ◽  
Water Film ◽  
Probe Design ◽  
Two Phase ◽  
Water Film Thickness ◽  
Wet Gas ◽  
Flow Phenomena ◽  
In Series ◽  
Electromagnetic Probes

The distribution of water in the diffuser of a wet gas compressor is not well understood. Measurements of water film thickness across the diffuser surface would improve the understanding of two-phase flow phenomena in wet gas compressors. Electromagnetic probes were designed in order to measure water film thickness in the diffuser of a SwRI-designed wet gas compressor. The probes consisted of two electrode foils plated on a thin insulating substrate, allowing them to be bonded in place without drilling through the diffuser. An AC signal was passed between the electrodes, and the voltage across a resistor in series with the electrodes was recorded. As the water level covering the electrodes increased, the recorded voltage increased. A method of calibrating the probes was developed and used prior to installation in the diffuser. Testing showed the probes to be effective at detecting the presence of water in the diffuser and indicating the general water level. Improvements in probe design, calibration, and installation are needed to provide more precise water film thickness data.

Effects and threshold of water film thickness on multi-mineral cement paste

2020 ◽  
Vol 112 ◽  
pp. 103677 ◽  
Author(s):  
Hengrui Liu ◽  
Xiao Sun ◽  
Hui Du ◽  
Hao Lu ◽  
Yuanshan Ma ◽  
...  
Keyword(s):  
Film Thickness ◽  
Cement Paste ◽  
Water Film ◽  
Water Film Thickness

Influences of fiber length and water film thickness on fresh properties of basalt fiber-reinforced mortar

2021 ◽  
Vol 22 (5) ◽  
pp. 344-356
Author(s):  
Leo Gu Li ◽  
Yi Ouyang ◽  
Pui-Lam Ng ◽  
Kai-long Zeng ◽  
Albert Kwok Hung Kwan
Keyword(s):  
Film Thickness ◽  
Fiber Length ◽  
Basalt Fiber ◽  
Water Film ◽  
Fiber Reinforced ◽  
Fresh Properties ◽  
Water Film Thickness
Sign in / Sign up

Export Citation Format

Share Document