scholarly journals Hydrogel-Core Microstructured Polymer Optical Fibers for Selective Fiber Enhanced Raman Spectroscopy

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1845
Author(s):  
Mikel Azkune ◽  
Igor Ayesta ◽  
Leire Ruiz-Rubio ◽  
Eneko Arrospide ◽  
Jose Luis Vilas-Vilela ◽  
...  

A new approach of Fiber Enhanced Raman Spectroscopy (FERS) is described within this article based on the use of Hydrogel-Core microstructured Polymer Optical Fibers (HyC-mPOF). The incorporation of the hydrogel only on the core of the Hollow-Core microstructured Polymer Optical Fiber (HC-mPOF) enables to perform FERS measurements in a functionalized matrix, enabling high selectivity Raman measurements. The hydrogel formation was continuously monitored and quantified using a Principal Component Analysis verifying the coherence between the components and the Raman spectrum of the hydrogel. The performed measurements with high and low affinity target molecules prove the feasibility of the presented HyC-mPOF platform.

1992 ◽  
Vol 247 ◽  
Author(s):  
Yasuhiro Koike

ABSTRACTHigh-bandwidth graded-index (GI) polymer optical fiber (POF) and single-mode POF with good mechanical properties were successfully obtained by our interfacial-gel polymerization technique. The bandwidth of the GI POF is about 1 GHz · km which is two hundred times larger than that of the conventional step-index (SI) POF. The minimum attenuation of transmission is 56 dB/km at 688-nm wavelength and 94 dB/km at 780-nm wavelength. The single-mode POF in which the core diameter was 3–15 μ m and the attenuation of transmission was 200 dB/km at 652-nm wavelength was successfully obtained for the first time.


The Analyst ◽  
2020 ◽  
Vol 145 (15) ◽  
pp. 5307-5313
Author(s):  
Huan Lin ◽  
Xin Cheng ◽  
Ming-Jie Yin ◽  
Zhouzhou Bao ◽  
Xunbin Wei ◽  
...  

A flexible porphyrin doped polymer optical fiber was developed for fast and highly sensitive monitoring of DNT vapors.


Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2776
Author(s):  
José A. Borda-Hernández ◽  
Claudia M. Serpa-Imbett ◽  
Hugo E. Hernandez Figueroa

This research introduces a numerical design of an air-core vortex polymer optical fiber in cyclic transparent optical polymer (CYTOP) that propagates 32 orbital angular momentum (OAM) modes, i.e., it may support up to 64 stable OAM-states considering left- and right-handed circular polarizations. This fiber seeks to be an alternative to increase the capacity of short-range optical communication systems multiplexed by modes, in agreement with the high demand of low-cost, insensitive-to-bending and easy-to-handle fibers similar to others optical fibers fabricated in polymers. This novel fiber possesses unique characteristics: a diameter of 50 µm that would allow a high mechanical compatibility with commercially available polymer optical fibers, a difference of effective index between neighbor OAM modes of around 10−4 over a bandwidth from 1 to 1.6 µm, propagation losses of approximately 15 × 10−3 dB/m for all OAM modes, and a very low dispersion for OAM higher order modes (±l = 16) of up to +2.5 ps/km-nm compared with OAM lower order modes at a telecom wavelength of 1.3 µm, in which the CYTOP exhibits a minimal attenuation. The spectra of mutual coupling coefficients between modes are computed considering small bends of up to 3 cm of radius and slight ellipticity in the ring of up to 5%. Results show lower-charge weights for higher order OAM modes.


Sensors ◽  
2019 ◽  
Vol 19 (13) ◽  
pp. 3011 ◽  
Author(s):  
Claire Guignier ◽  
Brigitte Camillieri ◽  
Michel Schmid ◽  
René M. Rossi ◽  
Marie-Ange Bueno

The objective of this paper is to study the ability of polymer optical fiber (POF) to be inserted in a knitted fabric and to measure both pressure and friction when walking. Firstly, POF, marketed and in development, have been compared in terms of the required mechanical properties for the insertion of the fiber directly into a knitted fabric on an industrial scale, i.e. elongation, bending rigidity, and minimum bending radius before plastic deformation. Secondly, the chosen optical fiber was inserted inside several types of knitted fabric and was shown to be sensitive to friction and compression. The knitted structure with the highest sensitivity has been chosen for sock prototype manufacturing. Finally, a feasibility study with an instrumented sock showed that it is possible to detect the different phases of walking in terms of compression and friction.


1996 ◽  
Vol 05 (01) ◽  
pp. 73-88 ◽  
Author(s):  
T. YAMAMOTO ◽  
K. FUJII ◽  
A. TAGAYA ◽  
E. NIHEI ◽  
Y. KOIKE ◽  
...  

Basic characteristics of organic-dye doped polymer optical fibers (DPOFs) are demonstrated. The devices contain laser dye, such as Rhodamine 6G (R6G) and Rhodamine B (RB) in the core region. Firstly, amplification characteristics of DPOF amplifiers (PO-FAs) excited by a pulse-operated, doubled Nd:YAG laser are demonstrated, e.g., a 250 mm-length of RB-POFA gives 1 kW (30 dB) of amplified signal at 591 nm. Next, an all solid state system of RB DPOF laser (POFL) is discussed by numerical simulation and the experimental result of high-power amplified spontaneous emission (ASE) by strong excitation of DPOF is shown.


Polymers ◽  
2018 ◽  
Vol 10 (8) ◽  
pp. 899 ◽  
Author(s):  
Hanna Stawska ◽  
Maciej Popenda ◽  
Elżbieta Bereś-Pawlik

In this paper, we present numerical studies of several different structures of anti-resonant, hollow core optical fibers. The cladding of these fibers is based on the Kagomé lattice concept, with some of the core-surrounding lattice cells removed. This modification, by creating additional, glass-free regions around the core, results in a significant improvement of some important optical fiber parameters, such as confinement loss (CL), bending loss (BL), and dispersion parameter (D). According to the conducted simulations (with fused silica glass being the structure’s material), CL were reduced from ~0.36 dB/m to ~0.16 dB/m (at 760 nm wavelength) in case of the structure with removed cells, and did not exceed the value of 1 dB/m across the 700–850 nm wavelength range. Additionally, proposed structure exhibits a remarkably low value of D—from 1.5 to 2.5 ps/(nm × km) at the 700–800 nm wavelength range, while the BL were estimated to be below 0.25 dB/m for bending radius of ~1.5 cm. CL and D were simulated, additionally, for structures made of acrylic glass polymethylmethacrylate, (PMMA), with similarly good results—DPMMA ∊ [2, 4] ps/(nm × km) and CLPMMA ≈ 0.13 dB/m (down from 0.41 dB/m), for the same spectral regions (700–800 nm bandwidth for D, and 760 nm wavelength for CL).


Polymers ◽  
2018 ◽  
Vol 11 (1) ◽  
pp. 52 ◽  
Author(s):  
Igor Ayesta ◽  
Mikel Azkune ◽  
Eneko Arrospide ◽  
Jon Arrue ◽  
María Illarramendi ◽  
...  

This paper employs the solution-doping technique for the fabrication of active polymer optical fibers (POFs), in which the dopant molecules are directly incorporated into the core of non-doped uncladded fibers. Firstly, we characterize the insertion of a solution of rhodamine B and methanol into the core of the fiber samples at different temperatures, and we show that better optical characteristics, especially in the attenuation coefficient, are achieved at lower temperatures. Moreover, we also analyze the dependence of the emission features of doped fibers on both the propagation distance and the excitation time. Some of these features and the corresponding ones reported in the literature for typical active POFs doped with the same dopant are quantitatively similar among them. This applies to the spectral location of the absorption and the emission bands, the spectral displacement with propagation distance, and the linear attenuation coefficient. The samples prepared in the way described in this work present higher photostability than typical samples reported in the literature, which are prepared in different ways.


Photonics ◽  
2019 ◽  
Vol 6 (2) ◽  
pp. 36 ◽  
Author(s):  
Rui Min ◽  
Beatriz Ortega ◽  
Carlos Marques

Grating devices in polymer optical fibers (POFs) have attracted huge interest for many potential applications in recent years. This paper presents the state of the art regarding the fabrication of different types of POF gratings, such as uniform, phase-shifted, tilted, chirped, and long period gratings, and explores potential application scenarios, such as biosensing and optical communications.


Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3397
Author(s):  
María Ángeles Losada ◽  
María Mazo ◽  
Alicia López ◽  
Candela Muzás ◽  
Javier Mateo

Large-core polymer optical fiber (POF) links have limitations in capacity and reach due to the fibers’ high modal dispersion and attenuation. Most of these links use red laser diodes, even though the attenuation spectrum of poly(methyl methacrylate) (PMMA), the basic polymer used to manufacture these fibers, has a lower minimum in the green region. Therefore, we set out to explore the potential use of green light in transmission systems, comparing the performances of three step-index polymer optical fibers (SI-POFs) with different numerical apertures. We obtained measurements of intensity distribution, frequency response and bit error rate (BER), as functions of fiber length. We have also compared the fibers’ frequency responses with red and green light for a few selected lengths. Our results confirm that SI-POFs attenuate less in response to green light, which can increase their length. This advantage is partially counterbalanced by a slightly higher dispersion that limits the capacity of the high-aperture fibers, particularly at relatively short lengths. Our conclusions are critical to understanding SI-POF behavior and to designing thorough SI-POF models that can aid the design of POF-based links for different scenarios.


Sign in / Sign up

Export Citation Format

Share Document