Treatment of Dyeing and Printing Wastewater by Copper Oxide Loaded on Coconut Shell Activated Carbon

2011 ◽  
Vol 366 ◽  
pp. 412-415
Author(s):  
Yu De Liu ◽  
Bo Quan Jiang ◽  
Zheng Qiang Xiao
Keyword(s):  
Activated Carbon ◽  
Copper Oxide ◽  
Orthogonal Experiment ◽  
Chemical Activation ◽  
Copper Nitrate ◽  
Color Removal ◽  
Removal Rates ◽  
Activation Temperature ◽  
Coconut Shells ◽  
Coconut Shell Activated Carbon

The activated carbon loaded copper oxide catalyst was prepared from Hainan abandoned coconut shells using chemical activation method and applied in treatment of acid bright red GR simulation dyeing wastewater. The effects of phosphoric acid concentration, ratio of liquid to solid, activation time and activation temperature on the COD and color removal rates were investigated by orthogonal experiment. The results showed that the optimal values of the parameters above were 65% (in mass), 3:1, 2.5h and 500°C under the designed copper oxide loading conditions of calcining temperature 300°C,calcining time 3.0 h and use level of copper nitrate 15 mL. Using the prepared sample for the treatment of the wastewater, the COD and color removal rates reached 94.384% and 99.840%, respectively.

Preparation of Copper Oxide Loaded Activated Carbon by Waste Sawdust for Acid Red GR Wastewater Treatment

2011 ◽  
Vol 356-360 ◽  
pp. 395-398 ◽  
Author(s):  
Bo Quan Jiang ◽  
Zheng Qiang Xiao
Keyword(s):  
Activated Carbon ◽  
Copper Oxide ◽  
Copper Nitrate ◽  
Cod Removal ◽  
Wood Dust ◽  
Optimum Process ◽  
Process Conditions ◽  
Removal Rates ◽  
Activation Temperature ◽  
Color And Cod Removal

The waste wood dust was utilized to prepare the copper oxide loaded activated carbon for the treatment of the printing and dyeing wastewater (acid red GR wastewater). The response surface assisted with Design-Expert 7.0 software was used to optimize the process. The secondary multiple regression models for the color and COD removal rates were established and proven to be significant. The optimum process conditions determined by the software were: copper nitrate (0.5mol/L) 15mL, ratio of liquid to solid 56, activation temperature 690 °C and activation time 2.1h, under which the color and COD removal rates reached 99.8% and 88.34%, respectively.

Study on the Preparation of Activated Carbon from Corncobs

2013 ◽  
Vol 634-638 ◽  
pp. 1398-1403
Author(s):  
Jun Han Li ◽  
Shao Li Yang ◽  
Ning Sun ◽  
Lan Ma
Keyword(s):  
Activated Carbon ◽  
Orthogonal Experiment ◽  
Chemical Activation ◽  
Activation Process ◽  
Activator Concentration ◽  
Activation Effect ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
The Impact ◽  
Better Than

The impact of activator varieties on the activation effect in preparing activated carbon with corncob adopting chemical activation process were researched in this paper, the results showed that phosphoric acid as the activator was much better than potassium hydroxide and zinc chloride. It was deduced from the orthogonal experiment results that the impact of activation temperature on the activation effect is the greatest, impregnation ratio takes the second place, and the activator concentration the least. Suitable parameters of activation process were obtained: when the activator concentration is 50%, activation temperature 500°C, impregnation ratio 2.7:1, the iodine value of activated carbon is 822.08mg/g.

scholarly journals Characterization of Coconut Shell Activated Carbon Catalyst for the Pyrolysis of Waste Sac Bags into Liquid Hydrocarbon Fuels

2021 ◽  
pp. 43-50
Author(s):  
Kelechi Angelina Iheonye ◽  
Ifeanyichukwu Edeh ◽  
Ibrahim Kolawole Muritala ◽  
Ayoade Kuye
Keyword(s):  
Activated Carbon ◽  
Chemical Activation ◽  
Hydrocarbon Fuel ◽  
Hydrocarbon Fuels ◽  
Fuel Oil ◽  
Coconut Shell ◽  
Carbon Catalyst ◽  
Structural Morphology ◽  
Coconut Shells ◽  
Coconut Shell Activated Carbon

Aim: The use of synthetic catalysts in pyrolysis of waste plastics into hydrocarbon fuels is the common practice, these synthetic/ commercial catalysts are not readily available in Nigeria. The aim of this research paper is to prepare and characterize and test the catalytic performance of a locally made catalyst for waste plastic to hydrocarbon fuel pyrolysis. Study Design: locally made catalyst was prepared from coconut shells, its elemental composition, structural morphology and pore properties investigated using appropriate instruments and methods. Place and Duration: The experiments were carried out at the Petroleum Development Laboratory, situated at the Gas Engineering building, University of Port-Harcourt Nigeria. It took about 18 months to complete this study. Methodology: Thermal and chemical activation methods were used to prepare the local catalyst from coconut shells. Scanning electron microscopy method was used to investigate the morphology and texture of the coconut shell activated carbon catalyst. Response Surface Method (RSM) in design expert software 12.0 was used to design the experiment, and investigate the effect of operating parameters on the response variable. Results: The assessment of coconut shell activated carbon shows it can be used as an alternate to synthetic catalysts. This is because more than 60 % fuel oil was recovered when it was used in the pyrolysis of waste sac bags Conclusion: Coconut shell activated carbon is effective in the conversion of waste sac bags high purity hydrocarbon fuels such as aviation kerosene.

scholarly journals Characterization of Active Carbon Prepared from Coconuts Shells using FTIR, XRD and SEM Techniques

2018 ◽  
Vol 7 (1) ◽  
pp. 33 ◽  
Author(s):  
Andi Ikhtiar Bakti ◽  
Paulus Lobo Gareso
Keyword(s):  
Activated Carbon ◽  
Chemical Activation ◽  
X Ray Diffraction ◽  
Activation Temperature ◽  
X Ray ◽  
Carbon And Graphite ◽  
Diffraction Peaks ◽  
Coconut Shells ◽  
Physical And Chemical

Activated carbon is produced from coconut shells through physical and chemical activation. With pyrolysis method, the optimum activation temperature for physics activation is 600oC, and for chemical, activation is to soak it in activator ZnCl2 10% and Na2Ca3 10%. Activated carbon was analyzed by Fourier Transformation Infrared (FTIR) and X-ray Diffraction (XRD) methods. The FTIR result showed that the coconut shells succeeds in becoming carbon. The XRD results confirm the existence of several phases of crystals like graphite around the peaks of 36o and 44o, there are two wide diffraction peaks and can be interconnected with carbon and graphite content. The SEM result showed that the carbonization of pyrolysis and activation processes created porosity and a large surface area for absorption.Keywords: activated carbon, coconut shell, FTIR, SEM, XRD

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

scholarly journals Computer Analysis of the Effect of Activation Temperature on the Microporous Structure Development of Activated Carbon Derived from Common Polypody

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2951
Author(s):  
Mirosław Kwiatkowski ◽  
Jarosław Serafin ◽  
Andy M. Booth ◽  
Beata Michalkiewicz
Keyword(s):  
Activated Carbon ◽  
Porous Structure ◽  
Computer Analysis ◽  
Density Functional ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Geometrical Parameters ◽  
Activation Process ◽  
Microporous Structure ◽  
Activation Temperature

This paper presents the results of a computer analysis of the effect of activation process temperature on the development of the microporous structure of activated carbon derived from the leaves of common polypody (Polypodium vulgare) via chemical activation with phosphoric acid (H3PO4) at activation temperatures of 700, 800, and 900 °C. An unconventional approach to porous structure analysis, using the new numerical clustering-based adsorption analysis (LBET) method together with the implemented unique gas state equation, was used in this study. The LBET method is based on unique mathematical models that take into account, in addition to surface heterogeneity, the possibility of molecule clusters branching and the geometric and energy limitations of adsorbate cluster formation. It enabled us to determine a set of parameters comprehensively and reliably describing the porous structure of carbon material on the basis of the determined adsorption isotherm. Porous structure analyses using the LBET method were based on nitrogen (N2), carbon dioxide (CO2), and methane (CH4) adsorption isotherms determined for individual activated carbon. The analyses carried out showed the highest CO2 adsorption capacity for activated carbon obtained was at an activation temperature of 900 °C, a value only slightly higher than that obtained for activated carbon prepared at 700 °C, but the values of geometrical parameters determined for these activated carbons showed significant differences. The results of the analyses obtained with the LBET method were also compared with the results of iodine number analysis and the results obtained with the Brunauer–Emmett–Teller (BET), Dubinin–Radushkevich (DR), and quenched solid density functional theory (QSDFT) methods, demonstrating their complementarity.

Application of response surface methodology to optimize the fabrication of ZnCl2-activated carbon from sugarcane bagasse for the removal of Cu2+

2017 ◽  
Vol 75 (9) ◽  
pp. 2047-2055 ◽  
Author(s):  
Thuan Van Tran ◽  
Quynh Thi Phuong Bui ◽  
Trinh Duy Nguyen ◽  
Van Thi Thanh Ho ◽  
Long Giang Bach
Keyword(s):  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Sugarcane Bagasse ◽  
Interactive Effect ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Aqueous Environment ◽  
Activation Temperature

The present study focused on the application of response surface methodology to optimize the fabrication of activated carbon (AC) from sugarcane bagasse for adsorption of Cu2+ ion. The AC was synthesized via chemical activation with ZnCl2 as the activating agent. The central composite design based experiments were performed to assess the individual and interactive effect of influential parameters, including activation temperature, ZnCl2 impregnation ratio and activation time on the AC yield and removal of Cu2+ ion from the aqueous environment. The statistically significant, well-fitting quadratic regression models were successfully developed as confirmed by high F- and low P-values (<0.0001), high correlation coefficients and lack-of-fit tests. Accordingly, the optimum AC yield and removal efficiency of Cu2+ were predicted, respectively, as 48.8% and 92.7% which were approximate to the actual values. By applying the predicted optimal parameters, the AC shows a surprisingly high surface area of around 1,500 m2/g accompanied by large pore volume and narrow micropore size at low fabrication temperature.

Production of Activated Carbon from Ligin: Optimization Using Response Surface Methodology

2011 ◽  
Vol 213 ◽  
pp. 427-431 ◽  
Author(s):  
Li Jiang ◽  
Fei Ma ◽  
Ai Jun Gu ◽  
Li Jun Zhang
Keyword(s):  
Response Surface Methodology ◽  
Activated Carbon ◽  
Response Surface ◽  
Chemical Activation ◽  
Technological Parameters ◽  
Activation Temperature ◽  
Surface Areas ◽  
Optimum Response ◽  
Temperature Activation ◽  
Central Composite

Activated carbon（AC）were prepared from lignin by chemical activation with sodium hydroxide（NaOH）. The influence of activation temperature，activation time and impregnation ration on the BET surface areas were investigated. Based on the central composite design (CCD) and response surface methodology(RSM)，the optimized technological parameters were as follows: temperature 751°C， time 57min and impregnation ration 2.06, BET surface areas was up to 1437.20 m2/g.The adequacy of the model equation for predicting the optimum response values was verified effectively by the validation.

Preparation of activated carbons from wet activated sludge by direct chemical activation

2009 ◽  
Vol 59 (12) ◽  
pp. 2387-2394 ◽  
Author(s):  
X. Wang ◽  
N. Zhu ◽  
J. Xu ◽  
B. Yin
Keyword(s):  
Activated Carbon ◽  
Activated Sludge ◽  
Water Content ◽  
Iodine Value ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Processing Parameters ◽  
Experimental Conditions ◽  
Activation Temperature

An improved method for preparing activated carbons from wet waste activated sludge (WAS) by direct chemical activation was studied in this paper. The effects of processing parameters on iodine adsorption capacity of the product were investigated. Results show that sludge-based activated carbon prepared with KOH had a larger iodine value than those activated with ZnCl2 and KCl. The maximum iodine value was observed at the KOH concentration of 0.50 M. Increasing the impregnation time from 10 to 20 h resulted in a 20% increase in the iodine value. The highest iodine value was obtained at the activation temperature of 600°C and holding time of 1 h. Sludge water content had insignificant effects on the iodine value of products. Raw WAS with a water content of 93.2% can be converted into an activated carbon with a high specific surface area of 737.6 m2 g−1 and iodine value of 864.8 mgg−1 under optimum experimental conditions. Other physical properties such as total pore volume, micropore volume and mean pore diameter of the product were also reported and compared with those of commercial activated carbon.

A Highly Efficient Activated Carbon by Chemical Activation Method for Adsorption of Paraquat (Toxin)

2013 ◽  
Vol 773-774 ◽  
pp. 471-477
Author(s):  
Md Mokhlesur Rahman ◽  
Mohamed Awang ◽  
Mohosina Bintey Shajahan ◽  
Tariq Abdul Razak ◽  
Kamaruzzaman Yunus
Keyword(s):  
Activated Carbon ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Activation Method ◽  
Nacl Solution ◽  
Adsorption Ability ◽  
Activation Temperature ◽  
Highly Efficient ◽  
Surface Areas

The optimum condition for preparing a highly efficient activated carbon has been investigated in this work. The effects of different activation temperatures on the pore structure and surface morphology of highly efficient activated carbon (AC) derived from waste palm shell by chemical activation method using phosphoric acid as activating agent were studied. For activation, different activation temperatures in the range of 550 °C-650 °C were carried out. Activated carbon with well developed pore size were produced at activation temperature of 600 °C for 2 hours. At this temperature the Brunauer , Emmett and Teller (BET) surface areas are 1287 m2g-1, the total pore volume for adsorption and desorption are 0.742 cm3 g-1. Scanning Electron Microscope also confirmed the porosity of the highly efficient activated carbon. Finally it was tested in vitro to determine its adsorbing capacity for paraquat as a toxin. For optimum adsorption ability of activated carbon for paraquat, 0.9% NaCl solution is the most suitable solvent. The paraquat preferentially adsorbed onto the activated carbon in NaCl solution. The adsorption ability of the activated carbon (the amount adsorbed) for paraquat observed to be 99.9 mg g-1.

Sign in / Sign up

Export Citation Format

Share Document