A High-Order CMOS Bandgap Voltage Reference

2014 ◽  
Vol 989-994 ◽  
pp. 1165-1168
Author(s):  
Qian Neng Zhou ◽  
Yun Song Li ◽  
Jin Zhao Lin ◽  
Hong Juan Li ◽  
Chen Li ◽  
...  
Keyword(s):  
Power Supply ◽  
Supply Voltage ◽  
Absolute Temperature ◽  
High Order ◽  
Cmos Process ◽  
Voltage Reference ◽  
Power Supply Voltage ◽  
Power Supply Rejection Ratio ◽  
Voltage Deviation ◽  
Bandgap Voltage Reference

A high-order bandgap voltage reference (BGR) is designed by adopting a current which is proportional to absolute temperature T1.5. The high-order BGR is analyzed and simulated in SMIC 0.18μm CMOS process. Simulation results show that the designed high-order BGR achieves temperature coefficient of 2.54ppm/°C when temperature ranging from-55°C to 125°C. The high-order BGR at 10Hz, 100Hz, 1kHz, 10kHz and 100kHz achieves, respectively, the power supply rejection ratio of-64.01dB, -64.01dB, -64dB, -63.5dB and-53.2dB. When power supply voltage changes from 1.7V to 2.5V, the output voltage deviation of BGR is only 617.6μV.

A High Order Curvature-Compensated Bandgap Voltage Reference with a Novel Error Amplifier

2017 ◽  
Vol 26 (09) ◽  
pp. 1750127 ◽  
Author(s):  
Gongyuan Zhao ◽  
Mao Ye ◽  
Yiqiang Zhao ◽  
Kai Hu ◽  
Ruishan Xin
Keyword(s):  
Monte Carlo Simulation ◽  
Power Supply ◽  
Supply Voltage ◽  
High Order ◽  
Cmos Process ◽  
Voltage Reference ◽  
Temperature Dependent ◽  
Error Amplifier ◽  
Bandgap Voltage Reference ◽  
Simulation Results

This paper presents a bandgap voltage reference (BGR), utilizing high order curvature-compensated technique with the temperature dependent resistor. Based on an improved error amplifier, [Formula: see text]80[Formula: see text]dB power supply rejection (PSR) @1[Formula: see text]kHz is achieved without additional complicated circuits. The circuit is fabricated in a standard [Formula: see text]m CMOS process, consuming 50[Formula: see text][Formula: see text]A at 25[Formula: see text]C with a supply voltage of 3.3[Formula: see text]V. Simulation results show that the proposed BGR can achieve a temperature coefficient as low as 1.18[Formula: see text]ppm/[Formula: see text]C over the temperature range from [Formula: see text]C to 120[Formula: see text]C. Monte Carlo simulation and Experimental Results validate the design.

A High-Order Curvature-Compensated Bandgap Voltage Reference for Micro-Gyroscope

2012 ◽  
Vol 503 ◽  
pp. 12-17
Author(s):  
Qiang Li ◽  
Xiao Yun Tan ◽  
Guan Shi Wang
Keyword(s):  
Power Supply ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Bandgap Reference ◽  
Voltage Reference ◽  
Temperature Dependent ◽  
Power Supply Voltage ◽  
Gyroscope System ◽  
Bandgap Voltage Reference ◽  
Reference Circuit

The reference is an important part of the micro-gyroscope system. The precision and stability of the reference directly affect the precision of the micro-gyroscope. Unlike the traditional bandgap reference circuit, a circuit using a temperature-dependent resistor ratio generated by a highly-resistive poly resistor and a diffusion resistor in CMOS technology is proposed in this paper. The complexity of the circuit is greatly reduced. Implemented with the standard 0.5μm CMOS technology and 9V power supply voltage, in the range of -40~120°C, the temperature coefficient of the proposed bandgap voltage reference can achieve to about 1.6 ppm/°C. The PSRR of the circuit is -107dB.

scholarly journals A 0.6 V MOS-Only Voltage Reference for Biomedical Applications with 40 ppm/∘C Temperature Drift

2018 ◽  
Vol 27 (08) ◽  
pp. 1850128 ◽  
Author(s):  
R. Nagulapalli ◽  
K. Hayatleh ◽  
Steve Barker ◽  
Sumathi Raparthy ◽  
Nabil Yassine ◽  
...  
Keyword(s):  
Power Supply ◽  
Biomedical Applications ◽  
Low Voltage ◽  
Supply Voltage ◽  
Absolute Temperature ◽  
Voltage Reference ◽  
Mos Transistors ◽  
Power Supply Voltage ◽  
Temperature Drift ◽  
Ultra Low Power

This paper exploits the CMOS beta multiplier circuit to synthesize a temperature-independent voltage reference suitable for low voltage and ultra-low power biomedical applications. The technique presented here uses only MOS transistors to generate Proportional To Absolute Temperature (PTAT) and Complimentary To Absolute Temperature (CTAT) currents. A self-biasing technique has been used to minimize the temperature and power supply dependency. A prototype in 65[Formula: see text]nm CMOS has been developed and occupies 0.0039[Formula: see text]mm2, and at room temperature, it generates a 204[Formula: see text]mV reference voltage with 1.3[Formula: see text]mV drift over a wide temperature range (from [Formula: see text]40[Formula: see text]C to 125[Formula: see text]C). This has been designed to operate with a power supply voltage down to 0.6[Formula: see text]V and consumes 1.8[Formula: see text]uA current from the supply. The simulated temperature coefficient is 40[Formula: see text]ppm/[Formula: see text]C.

scholarly journals A sub-1V high PSRR OpAmp based β-multiplier CMOS bandgap voltage reference with resistive division

2019 ◽  
Vol 15 (1) ◽  
pp. 155
Author(s):  
Anass SLAMTI ◽  
Youness MEHDAOUI ◽  
Driss CHENOUNI ◽  
Zakia LAKHLIAI
Keyword(s):  
Temperature Coefficient ◽  
Power Supply ◽  
Supply Voltage ◽  
Voltage Source ◽  
Voltage Reference ◽  
Voltage Range ◽  
Rejection Ratio ◽  
Power Supply Rejection Ratio ◽  
Bandgap Voltage Reference ◽  
Supply Rejection

<span lang="EN-US">A sub-1V opamp based β-multiplier CMOS bandgap voltage reference (BGVR) with high power supply rejection ratio (PSRR) and low temperature coefficient (TC) is proposed in this paper. A current mode regulator scheme is inserted to isolate the supply voltage of the operational amplifier (opamp) and the supply voltage of the BGVR core from the supply voltage source in order to reduce ripple sensitivity and to achieve a high PSRR. The proposed circuit is designed and simulated in 0.18-μm standard CMOS technology. The proposed voltage reference delivers an output voltage of 634.6mV at 27°C. Tthe measurement temperature coefficient is 22,3ppm/°C over temperature range -40°C to 140°C, power supply rejection ratio is -93dB at 10kHz and -71dB at 1MHz and a line regulation of 104μV/V is achieved over supply voltage range 1.2V to 1.8V. The layout area of the proposed circuit is 0.0337mm<sup>2</sup>. The proposed sub-1V bandgap voltage reference can be used as an internal voltage reference in low power LDO regulators and switching regulators.</span>

Integrated Bandgap Voltage Reference for High Voltage Vehicle Applications

2015 ◽  
Vol 24 (08) ◽  
pp. 1550125 ◽  
Author(s):  
Sergio Saponara
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Supply Voltage ◽  
Input Voltage ◽  
Voltage Reference ◽  
Temperature Drift ◽  
Power Supply Rejection Ratio ◽  
Compact Size ◽  
Electrical Vehicles ◽  
Bandgap Voltage Reference

This work presents a bandgap voltage reference (BGR) integrated in 0.25-μm bipolar-CMOS-DMOS (BCD) technology. The BGR circuit generates a reference voltage of 1.22 V. It is able to withstand large supply voltage variations of vehicle applications from 4.5 V, e.g., in case of cranking, up to 60-V, maximum value in case of emerging 48-V battery systems for hybrid and electrical vehicles. The circuit has an embedded high-voltage (HV) pseudo-regulator block that provides a more stable internal supply rail for a cascaded low-voltage bandgap core. HV MOS are used only in the pre-regulator block thus allowing the design of a BGR with compact size. The proposed architecture permits to withstand large input voltage variations with a temperature drift of a hundred of ppm/°C, a line regulation (LR) of few mV/V versus the external supply voltage and a power supply rejection ratio (PSRR) higher than 90 dB.

Design of a High Performance CMOS Bandgap Voltage Reference

2014 ◽  
Vol 981 ◽  
pp. 90-93
Author(s):  
Yang Guang ◽  
Bin Yu ◽  
Huang Hai
Keyword(s):  
Integrated Circuits ◽  
High Performance ◽  
Circuit Simulation ◽  
Absolute Temperature ◽  
Reference Voltage ◽  
Cmos Process ◽  
Voltage Reference ◽  
Temperature Changes ◽  
Bandgap Voltage Reference ◽  
Protection Circuit

Bandgap voltage reference, to provide a temperature and power supply insensitive output voltage, is a very important module in the analog integrated circuits and mixed-signal integrated circuits. In this paper, a high performance CMOS bandgap with low-power consumption has been designed. It can get the PTAT (Proportional to absolute temperature) current, and then get the reference voltage. Based on 0.35μm CMOS process, using HSPICE 2008 software for circuit simulation, the results showed that , when the temperature changes from -40 to 80 °C, the proposed circuit’s reference voltage achieve to 1.2V, temperature coefficient is 3.09ppm/°C. Adopt a series of measures, like ESD protection circuit, in layout design. The ultimately design through the DRC and LVS verification, and the final layout size is 700μm * 560μm.

Single Inductor Bipolar Outputs DC-DC Converter with Current Mode Control Circuit

2013 ◽  
Vol 534 ◽  
pp. 220-226 ◽  
Author(s):  
Nobukazu Takai ◽  
Takashi Okada ◽  
Kenji Takahashi ◽  
Hajime Yokoo ◽  
Shunsuke Miwa ◽  
...  
Keyword(s):  
Power Supply ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Process ◽  
Power Supply Voltage ◽  
Negative Power ◽  
Current Mode Control ◽  
Mode Control ◽  
Digital Still Camera ◽  
Simulation Results

Mobile equipment such as organic-EL display, digital still camera and so on re-quire both positive and negative power supply voltage to obtain high quality. Single InductorMultiple-Output (SIMO) DC-DC converter can provide a pair of positive and negative outputvoltages with only one external inductor. This paper describes SIMO DC-DC Converter usingproposed current-mode control (CMC) circuit. The proposed CMC circuit realizes high responsespeed for the change of load current. Spectre simulations with 0.18m CMOS process parameterare performed to verify the validity of the proposed converter. The simulation results indicatethat the proposed converter has higher response time compared with conventional converter.

A CMOS Self-Bias CTAT Current Generator with Improved Supply Sensitivity

2019 ◽  
Vol 28 (13) ◽  
pp. 1950226
Author(s):  
R. Nagulapalli
Keyword(s):  
Power Supply ◽  
Supply Voltage ◽  
Current Mode ◽  
Absolute Temperature ◽  
Loop Gain ◽  
Power Supply Voltage ◽  
Silicon Area ◽  
Simple Modification ◽  
Self Bias ◽  
Additional Circuitry

The role of complimentary to absolute temperature (CTAT) circuit in current mode bandgap has been described. Loop-gain problems with the existing self-bias MOS-based CTAT generator were discussed. A simple modification to the existing circuit was proposed to enhance the loop-gain by [Formula: see text]20[Formula: see text]dB without adding additional circuitry leading to zero additional power consumption. Power Supply Rejection and sensitivity to [Formula: see text] will be improved due to the higher loop-gain. A prototype has been developed to demonstrate the proposal robustness across PVT corners. Simulation results show 20.5[Formula: see text]dB PSRR improvement and 7.5% improvement in sensitivity to [Formula: see text]. The proposed solution consumes 180[Formula: see text]nW power from 1[Formula: see text]V power supply voltage and occupies 3300[Formula: see text][Formula: see text]m2 silicon area.

Integral Type Multi-Ramp for Single-Slope ADC

2013 ◽  
Vol 303-306 ◽  
pp. 1908-1912 ◽  
Author(s):  
Nan Lyu ◽  
Ning Mei Yu ◽  
He Jiu Zhang
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
Supply Voltage ◽  
High Accuracy ◽  
Sampling Frequency ◽  
Cmos Process ◽  
Voltage Reference ◽  
Integral Type ◽  
Power Supply Voltage ◽  
The One

This paper presents a integral type Multi-ramp architecture apply to MRSS ADC (Multiple-ramp single-slope ADC).On the one hand to improve the capacitance mismatch by change voltage reference, On the other hand to reduced the power consumption greatly. Implemented in the GSMC 180nm 2P4M CMOS process, in the power supply voltage of 1.8 V, 11-bit resolution, 10 MHZ sampling frequency, the result of max power consumption is 1.33mW of single unit .The DNL < 0.1LSB and max INL < 0.49LSB .The Multi-ramp achieved requirements for high speed and high accuracy MRSS ADC.

DESIGN OF A CMOS BANDGAP REFERENCE CIRCUIT WITH A WIDE TEMPERATURE RANGE, HIGH PRECISION AND LOW TEMPERATURE COEFFICIENT

2014 ◽  
Vol 23 (08) ◽  
pp. 1450107 ◽  
Author(s):  
JUN-DA CHEN ◽  
CHENG-KAI YE
Keyword(s):  
Temperature Coefficient ◽  
High Precision ◽  
Supply Voltage ◽  
Cmos Process ◽  
Voltage Reference ◽  
Temperature Range ◽  
Wide Range ◽  
Bandgap Voltage Reference ◽  
Reference Circuit ◽  
Cmos Voltage Reference

This paper presents an approach to the design of a high-precision CMOS voltage reference. The proposed circuit is designed for TSMC 0.35 μm standard CMOS process. We design the first-order temperature compensation bandgap voltage reference circuit. The proposed post-simulated circuit delivers an output voltage of 0.596 V and achieves the reported temperature coefficient (TC) of 3.96 ppm/°C within the temperature range from -60°C to 130°C when the supply voltage is 1.8 V. When simulated in a smaller temperature range from -40°C to 80°C, the circuit achieves the lowest reported TC of 2.09 ppm/°C. The reference current is 16.586 μA. This circuit provides good performances in a wide range of temperature with very small TC.

Sign in / Sign up

Export Citation Format

Share Document