scholarly journals Characterization of the Surface of Activated Carbons Produced from Tire Residues

2010 ◽  
Vol 636-637 ◽  
pp. 1383-1388
Author(s):  
J.M. Valente Nabais ◽  
Carlos Laginhas ◽  
Peter J.M. Carrott ◽  
Manuela M.L. Ribeiro Carrott ◽  
Cristina Galacho ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Xrd Analysis ◽  
Point Of Zero Charge ◽  
Surface Functional Groups ◽  
Surface Characterisation ◽  
Environment Friendly ◽  
Carbon Production

The surface characterisation of new activated carbons produced from tire residues by activation with carbon dioxide was studied. The activated carbons produced were mainly basic with point of zero charge values above 8.8. The main surface functional groups identified by FTIR were ether, quinones, lactones, ketones, hydroxyls (free and phenol) and pyrones. The XRD analysis shows that the materials produced have a microstructural organisation with microcrystallite height around 1.5nm and width from 3 to 5.3nm. This analysis indicates also the possible presence of oxides (single or mixture) of the following heteroatoms: Fe, Al, Ca, Mg, Ti, Si, K, Pb, Cd, Ba, Zn and Sn. The results have shown the significant potential of this type of residues for activated carbon production. Furthermore, the environment friendly use of an industrial residue is also noteworthy.

scholarly journals Comparison of Surface and Structural Properties of Carbonaceous Materials Prepared by Chemical Activation of Tomato Paste Waste: The Effects of Activator Type and Impregnation Ratio

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Nurgul Ozbay ◽  
Adife Seyda Yargic
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Nitrogen Adsorption ◽  
Xrd Analysis ◽  
Point Of Zero Charge ◽  
Activation Process ◽  
X Ray ◽  
Tomato Paste

Activated carbons were prepared by carbonization of tomato paste processing industry waste at 500°C followed by chemical activation with KOH, K2CO3, and HCl in N2 atmosphere at low temperature (500°C). The effects of different activating agents and impregnation ratios (25, 50, and 100 wt.%) on the materials’ characteristics were examined. Precursor, carbonized tomato waste (CTW), and activated carbons were characterized by using ultimate and proximate analysis, thermogravimetric analysis (TG/DTG), Fourier transform-infrared (FT-IR) spectroscopy, X-ray fluorescence (XRF) spectroscopy, point of zero charge measurements (pHPZC), particle size analyzer, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, nitrogen adsorption/desorption isotherms, and X-ray diffraction (XRD) analysis. Activation process improved pore formation and changed activated carbons’ surface characteristics. Activated carbon with the highest surface area (283 m3/g) was prepared by using 50 wt.% KOH as an activator. According to the experimental results, tomato paste waste could be used as an alternative precursor to produce low-cost activated carbon.

scholarly journals Effects of Gasifying Agents on the Characterization of Nut Shell-derived Activated Carbon

1995 ◽  
Vol 12 (3) ◽  
pp. 247-258 ◽  
Author(s):  
C. Nguyen ◽  
A. Ahmadpour ◽  
D.D. Do
Keyword(s):  
Carbon Dioxide ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Benzene Adsorption ◽  
Surface Areas ◽  
Activating Agent ◽  
Micropore Size ◽  
Adsorptive Properties ◽  
Insight Into

Activated carbon was prepared from nut shells using a conventional two-stage method: carbonization followed by activation. Activation with steam or carbon dioxide as activating agent produced a range of chars of different burn-off. These were characterized for their total and micropore surface areas, and benzene adsorption capacity. Benzene adsorption measurement provided an insight into the effect of porosity development on the adsorptive properties of the adsorbent. It was found that activated carbon products from nut shells were comparable, in terms of adsorption characteristics, with activated carbons from other lignocellulosic precursors. The evolution of porosity of the resulting carbons shows that carbon dioxide is the preferable agent for the production of activated carbon with a narrow micropore size distribution.

scholarly journals Production and Characterization of Activated Carbon from Baobab Fruit Shells by Chemical Activation Using ZnCl2, H3PO4 and KOH

2021 ◽  
Vol 2129 (1) ◽  
pp. 012009
Author(s):  
R Nedjai ◽  
N A Kabbashi ◽  
M Z Alam ◽  
M F R Al-Khatib
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Xrd Analysis ◽  
Surface Characteristic ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Ft Ir ◽  
Characterization Of Activated Carbon

Abstract Chemical agents have a good influence on the formation of activated carbons, surface characteristic, and its adsorption properties. In this study, the effect of activating agents (ZnCl2, KOH, and H3PO4) on baobab fruit shell (BFS) were evaluated. The characteristics of the baobab fruit shell based activated carbon (BF-ACs) were evaluated through the yield and iodine number. BF-ACs were also characterized by Scanning Electron Microscope (SEM), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Diffraction (XRD), and nitrogen (N2) adsorption. SEM analysis illustrates those porous structures formed on the surface of BF-ACs were with different sizes. The XRD analysis show that the main structures of BF-ACs are amorphous. FT-IR data demonstrates the presence of different surface groups on the produced BF-ACs. Among activating agent, the KOH was observed to the most appropriate for the production of activated carbon with a large surface area (1029.44 m2/g) from baobab fruit shell.

PREPARATION AND CHARACTERIZATION OF ACTIVATED CARBON FROM OIL PALM EMPTY FRUIT BUNCH WASTES USING ZINC CHLORIDE

2015 ◽  
Vol 74 (11) ◽  
Author(s):  
Riry Wirasnita ◽  
Tony Hadibarata ◽  
Abdull Rahim Mohd Yusoff ◽  
Zainab Mat Lazim
Keyword(s):  
Activated Carbon ◽  
Zinc Chloride ◽  
Oil Palm ◽  
Active Sites ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Proximate Analysis ◽  
Infrared Spectrometry ◽  
Empty Fruit Bunch

An oil palm empty fruit bunch-derived activated carbon has been successfully produced by chemical activation with zinc chloride and without chemical activation. The preparation was conducted in the tube furnace at 500oC for 1 h. The surface structure and active sites of activated carbons were characterized by means of Fourier transform infrared spectrometry and field emission scanning electron microscopy. The proximate analysis including moisture content, ash content, bulk density, pH, and pH at zero charge was conducted to identify the psychochemical properties of the adsorbent. The results showed that the zinc chloride-activated carbon has better characteristics compared to the carbon without chemical activation.  

scholarly journals Removal of Ni (II) from Aqueous Solution by Adsorption onto Activated Carbon Prepared from Lapsi (Choerospondias axillaris) Seed Stone

2014 ◽  
Vol 9 (1) ◽  
pp. 166-174 ◽  
Author(s):  
Rajeshwar M. Shrestha ◽  
Margit Varga ◽  
Imre Varga ◽  
Amar P. Yadav ◽  
Bhadra P. Pokharel ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Characterization ◽  
Maximum Adsorption Capacity ◽  
Adsorption Data ◽  
Optimum Ph ◽  
Nickel Adsorption

Activated carbons were prepared from Lapsi seed stone by the treatment with H2SO4 and HNO3 for the removal of Ni (II) ions from aqueous solution. Two activated carbon have been prepared from Lapsi seed stones by treating with conc.H2SO4 and a mixture of H2SO4 and HNO3 in the ratio of 1:1 by weight for removal of Ni(II) ions. Chemical characterization of the resultant activated carbons was studied by Fourier Transform Infrared Spectroscopy and Boehm titration which revealed the presence of oxygen containing surface functional groups like carboxyl, lactones and phenols in the carbons. The optimum pH for nickel adsorption is found to be 5. The adsorption data were better fitted with the Langmuir equations than Freundlich adsorption equation to describe the equilibrium isotherms. The maximum adsorption capacity of Ni (II) on the resultant activated carbons was 28.25.8 mg g-1 with H2SO4 and 69.49 mg g-1 with a mixture of H2SO4 and HNO3. The waste material used in the preparation of the activated carbons is inexpensive and readily available. Hence the carbons prepared from Lapsi seed stones can act as potential low cost adsorbents for the removal of Ni (II) from water. DOI: http://dx.doi.org/10.3126/jie.v9i1.10680Journal of the Institute of Engineering, Vol. 9, No. 1, pp. 166–174

scholarly journals Optimisation of durian peel based activated carbon preparation conditions for dye removal

2013 ◽  
Vol 16 (1) ◽  
pp. 22-31
Author(s):  
Phung Thi Kim Le ◽  
Kien Anh Le
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Dye Removal ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Impregnation Ratio ◽  
Carbon Production ◽  
Removal Capacity

Agricultural wastes are considered to be a very important feedstock for activated carbon production as they are renewable sources and low cost materials. This study present the optimize conditions for preparation of durian peel activated carbon (DPAC) for removal of methylene blue (MB) from synthetic effluents. The effects of carbonization temperature (from 673K to 923K) and impregnation ratio (from 0.2 to 1.0) with potassium hydroxide KOH on the yield, surface area and the dye adsorbed capacity of the activated carbons were investigated. The dye removal capacity was evaluated with methylene blue. In comparison with the commercial grade carbons, the activated carbons from durian peel showed considerably higher surface area especially in the suitable temperate and impregnation ratio of activated carbon production. Methylene blue removal capacity appeared to be comparable to commercial products; it shows the potential of durian peel as a biomass source to produce adsorbents for waste water treatment and other application. Optimize condition for preparation of DPAC determined by using response surface methodology was at temperature 760 K and IR 1.0 which resulted the yield (51%), surface area (786 m2/g), and MB removal (172 mg/g).

scholarly journals Preparation and characterization of activated carbons from albizia saman pod

2017 ◽  
Vol 36 (3) ◽  
pp. 44-53
Author(s):  
G. D. Akpen ◽  
M. I. Aho ◽  
N. Baba
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Activated Carbons ◽  
High Surface ◽  
High Surface Area ◽  
Volatile Matter ◽  
Sieve Analysis ◽  
Albizia Saman ◽  
Temperature Surface

Activated carbon was prepared from the pods of Albizia saman for the purpose of converting the waste to wealth. The pods were thoroughly washed with water to remove any dirt, air- dried and cut into sizes of 2-4 cm. The prepared pods were then carbonised in a muffle furnace at temperatures of 4000C, 5000C, 6000C ,7000C and 8000C for 30 minutes. The same procedure was repeated for 60, 90, 120 and 150 minutes respectively. Activation was done using impregnationratios of 1:12, 1:6, 1:4, 1:3, and 1:2 respectively of ZnCl2 to carbonised Albizia saman pods by weight. The activated carbon was then dried in an oven at 1050C before crushing for sieve analysis. The following properties of the produced Albizia saman pod activated carbon (ASPAC) were determined: bulk density, carbon yield, surface area and ash, volatile matter and moisture contents. The highest surface area of 1479.29 m2/g was obtained at the optimum impregnation ratio, carbonization time and temperature of 1:6, 60 minutes and 5000C respectively. It was recommended that activated carbon should be prepared from Albizia saman pod with high potential for adsorption of pollutants given the high surface area obtained.Keywords: Albizia saman pod, activated carbon, carbonization, temperature, surface area

scholarly journals Preparation and characterization of activated carbon from sewage sludge: carbonization step

2004 ◽  
Vol 49 (1) ◽  
pp. 139-146 ◽  
Author(s):  
S. Rio ◽  
C. Faur-Brasquet ◽  
L. Le Coq ◽  
D. Lecomte ◽  
P. Le Cloirec
Keyword(s):  
Wastewater Treatment ◽  
Activated Carbon ◽  
Sewage Sludge ◽  
Thermal Treatment ◽  
Wastewater Treatment Plants ◽  
Carbonization Temperature ◽  
Carbon Production ◽  
By Products ◽  
Characterization Of Activated Carbon

Sewage sludges produced from wastewater treatment plants continue to create environmental problems in terms of volume and method of valorization. Thermal treatment of sewage sludge is considered as an attractive method in reducing sludge volume which at the same time produces reusable by-products. This paper deals with the first step of activated carbon production from sewage sludge, the carbonization step. Experiments are carried out on viscous liquid sludge and limed sludge by varying carbonization temperature and heating rate. The results show that carbonized residue properties are interesting for activated carbon production.

scholarly journals Waste biomass as sources for activated carbon production-A review

2013 ◽  
Vol 47 (4) ◽  
pp. 347-364 ◽  
Author(s):  
MS Islam ◽  
MA Rouf
Keyword(s):  
Activated Carbon ◽  
Process Parameters ◽  
Activated Carbons ◽  
Low Cost ◽  
Process Conditions ◽  
Waste Biomass ◽  
Active Carbons ◽  
Carbon Production ◽  
Surface Areas ◽  
Physical And Chemical

A review of the production of activated carbons from waste biomass has been presented. The effects of various process parameters on the pyrolysis stage have been reviewed. Influences of activating conditions, physical and chemical, on the active carbon properties have been discussed. Under certain process conditions several active carbons with BET surface areas, ranging between 250 and 2410 m2/g and pore volumes of 0.022 and 91.4 cm3/g, have been produced. A comparison in characteristics and uses of activated carbons from waste biomass with those of commercial carbons has been made. Waste biomass being highly efficient, low cost and renewable sources of activated carbon production. Bangladesh J. Sci. Ind. Res. 47(4), 347-364, 2012 DOI: http://dx.doi.org/10.3329/bjsir.v47i4.14064

scholarly journals Progress in the Characterization of the Surface Species in Activated Carbons by means of INS Spectroscopy Coupled with Detailed DFT Calculations

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Andrea Piovano ◽  
Andrea Lazzarini ◽  
Riccardo Pellegrini ◽  
Giuseppe Leofanti ◽  
Giovanni Agostini ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Inelastic Neutron ◽  
Industrial Applications ◽  
Surface Species ◽  
Dft Methods ◽  
Neutron Spectra ◽  
Out Of Plane ◽  
Bending Modes

Activated carbons are materials with relevance in different industrial applications. Due to the inherent complexity and heterogeneity of their structures, an easy assignment of the species present on their surface has a challenging result. Only recently, with the possibility to collect well-resolved inelastic neutron spectra and to simulate by DFT methods more or less extended graphitic clusters, this task is starting to become feasible. Here we report our investigation on a steam activated carbon and we show that different vibrations in the region of out-of-plane C-H bending modes are specifically connected to hydrogen terminations belonging to extended and regular borders or to short and defective ones. Furthermore, simulations including heteroatoms such as oxygen allowed us to point out spectral regions with a contribution from carboxyl species.

Sign in / Sign up

Export Citation Format

Share Document