scholarly journals MONITORING HIGH-FREQUENCY OCEAN SIGNALS USING LOW-COST GNSS/IMU BUOYS

2016 ◽  
Vol XLI-B8 ◽  
pp. 1127-1134 ◽  
Author(s):  
Yu-Lun Huang ◽  
Chung-Yen Kuo ◽  
Chiao-Hui Shih ◽  
Li-Ching Lin ◽  
Kai-wei Chiang ◽  
...  
Keyword(s):  
Sea Level ◽  
High Frequency ◽  
Field Experiments ◽  
Tide Gauge ◽  
Low Cost ◽  
Main Idea ◽  
Measurement Unit ◽  
Frequency Noise ◽  
Human Beings ◽  
Tide Gauges

In oceans there are different ocean signals covering the multi-frequencies including tsunami, meteotsunami, storm surge, as sea level change, and currents. These signals have the direct and significant impact on the economy and life of human-beings. Therefore, measuring ocean signals accurately becomes more and more important and necessary. Nowadays, there are many techniques and methods commonly used for monitoring oceans, but each has its limitation. For example, tide gauges only measure sea level relative to benchmarks and are disturbed unevenly, and satellite altimeter measurements are not continuous and inaccurate near coastal oceans. In addition, high-frequency ocean signals such as tsunami and meteotsunami cannot be sufficiently detected by 6-minutes tide gauge measurements or 10-day sampled altimetry data. Moreover, traditional accelerometer buoy is heavy, expensive and the low-frequency noise caused by the instrument is unavoidable. In this study, a small, low-cost and self-assembly autonomous Inertial Measurement Unit (IMU) that independently collects continuous acceleration and angular velocity data is mounted on a GNSS buoy to provide the positions and tilts of the moving buoy. The main idea is to integrate the Differential GNSS (DGNSS) or Precise Point Positioning (PPP) solutions with IMU data, and then evaluate the performance by comparing with in situ tide gauges. The validation experiments conducted in the NCKU Tainan Hydraulics Laboratory showed that GNSS and IMU both can detect the simulated regular wave frequency and height, and the field experiments in the Anping Harbor, Tainan, Taiwan showed that the low-cost GNSS buoy has an excellent ability to observe significant wave heights in amplitude and frequency.

scholarly journals MONITORING HIGH-FREQUENCY OCEAN SIGNALS USING LOW-COST GNSS/IMU BUOYS

2016 ◽  
Vol XLI-B8 ◽  
pp. 1127-1134
Author(s):  
Yu-Lun Huang ◽  
Chung-Yen Kuo ◽  
Chiao-Hui Shih ◽  
Li-Ching Lin ◽  
Kai-wei Chiang ◽  
...  
Keyword(s):  
Sea Level ◽  
High Frequency ◽  
Field Experiments ◽  
Tide Gauge ◽  
Low Cost ◽  
Main Idea ◽  
Measurement Unit ◽  
Frequency Noise ◽  
Human Beings ◽  
Tide Gauges

In oceans there are different ocean signals covering the multi-frequencies including tsunami, meteotsunami, storm surge, as sea level change, and currents. These signals have the direct and significant impact on the economy and life of human-beings. Therefore, measuring ocean signals accurately becomes more and more important and necessary. Nowadays, there are many techniques and methods commonly used for monitoring oceans, but each has its limitation. For example, tide gauges only measure sea level relative to benchmarks and are disturbed unevenly, and satellite altimeter measurements are not continuous and inaccurate near coastal oceans. In addition, high-frequency ocean signals such as tsunami and meteotsunami cannot be sufficiently detected by 6-minutes tide gauge measurements or 10-day sampled altimetry data. Moreover, traditional accelerometer buoy is heavy, expensive and the low-frequency noise caused by the instrument is unavoidable. In this study, a small, low-cost and self-assembly autonomous Inertial Measurement Unit (IMU) that independently collects continuous acceleration and angular velocity data is mounted on a GNSS buoy to provide the positions and tilts of the moving buoy. The main idea is to integrate the Differential GNSS (DGNSS) or Precise Point Positioning (PPP) solutions with IMU data, and then evaluate the performance by comparing with in situ tide gauges. The validation experiments conducted in the NCKU Tainan Hydraulics Laboratory showed that GNSS and IMU both can detect the simulated regular wave frequency and height, and the field experiments in the Anping Harbor, Tainan, Taiwan showed that the low-cost GNSS buoy has an excellent ability to observe significant wave heights in amplitude and frequency.

scholarly journals Testing an “IoT” Tide Gauge Network for Coastal Monitoring

IoT ◽  
2021 ◽  
Vol 2 (1) ◽  
pp. 17-32
Author(s):  
Philip Knight ◽  
Cai Bird ◽  
Alex Sinclair ◽  
Jonathan Higham ◽  
Andy Plater
Keyword(s):  
Sea Level ◽  
Morphological Changes ◽  
Tide Gauge ◽  
Low Cost ◽  
Pressure Sensors ◽  
Wave Activity ◽  
Tide Gauges ◽  
Coastal Monitoring ◽  
Level Data ◽  
Operational Constraints

A low-cost “Internet of Things” (IoT) tide gauge network was developed to provide real-time and “delayed mode” sea-level data to support monitoring of spatial and temporal coastal morphological changes. It is based on the Arduino Sigfox MKR 1200 micro-controller platform with a Measurement Specialties pressure sensor (MS5837). Experiments at two sites colocated with established tide gauges show that these inexpensive pressure sensors can make accurate sea-level measurements. While these pressure sensors are capable of ~1 cm accuracy, as with other comparable gauges, the effect of significant wave activity can distort the overall sea-level measurements. Various off-the-shelf hardware and software configurations were tested to provide complementary data as part of a localized network and to overcome operational constraints, such as lack of suitable infrastructure for mounting the tide gauges and for exposed beach locations.

scholarly journals An Attempt to Observe Vertical Land Motion along the Norwegian Coast by CryoSat-2 and Tide Gauges

2019 ◽  
Vol 11 (7) ◽  
pp. 744 ◽  
Author(s):  
Martina Idžanović ◽  
Christian Gerlach ◽  
Kristian Breili ◽  
Ole Andersen
Keyword(s):  
Sea Level ◽  
High Frequency ◽  
Satellite Altimetry ◽  
Tide Gauge ◽  
Ice Sheets ◽  
Tide Gauges ◽  
Tide Gauge Data ◽  
Norwegian Coast ◽  
Vertical Land Motion ◽  
Gauge Data

Present-day climate-change-related ice-melting induces elastic glacial isostatic adjustment (GIA) effects, while paleo-GIA effects describe the ongoing viscous response to the melting of late-Pleistocene ice sheets. The unloading initiated an uplift of the crust close to the centers of former ice sheets. Today, vertical land motion (VLM) rates in Fennoscandia reach values up to around 10 mm/year and are dominated by GIA. Uplift signals from GIA can be computed by solving the sea-level equation (SLE), S ˙ = N ˙ − U ˙ . All three quantities can also be determined from geodetic observations: relative sea-level variations ( S ˙ ) are observed by means of tide gauges, while rates of absolute sea-level change ( N ˙ ) can be observed by satellite altimetry; rates of VLM ( U ˙ ) can be determined by GPS (Global Positioning System). Based on the SLE, U ˙ can be derived by combining sea-surface measurements from satellite altimetry and relative sea-level records from tide gauges. In the present study, we have combined 7.5 years of CryoSat-2 satellite altimetry and tide-gauge data to estimate linear VLM rates at 20 tide gauges along the Norwegian coast. Thereby, we made use of monthly averaged tide-gauge data from PSMSL (Permanent Service for Mean Sea Level) and a high-frequency tide-gauge data set with 10-min sampling rate from NMA (Norwegian Mapping Authority). To validate our VLM estimates, we have compared them with the independent semi-empirical land-uplift model NKG2016LU_abs for the Nordic-Baltic region, which is based on GPS, levelling, and geodynamical modeling. Estimated VLM rates from 1 Hz CryoSat-2 and high-frequency tide-gauge data reflect well the amplitude of coastal VLM as provided by NKG2016LU_abs. We find a coastal average of 2.4 mm/year (average over all tide gauges), while NKG2016LU_abs suggests 2.8 mm/year; the spatial correlation is 0.58.

scholarly journals Spectral Analysis of Satellite Altimeter and Tide Gauge Data around the Northern Australian Coast

2020 ◽  
Vol 12 (1) ◽  
pp. 161 ◽  
Author(s):  
Zahra Gharineiat ◽  
Xiaoli Deng
Keyword(s):  
Time Series ◽  
Sea Level ◽  
High Frequency ◽  
Tide Gauge ◽  
Tidal Range ◽  
Tide Gauges ◽  
The North ◽  
Power Spectral ◽  
Level Data ◽  
Tidal Constituents

The north of Australia is known for its complex tidal system, where the highest astronomical tides (HATs) reach 12 m. This paper investigates the tidal behaviour in this region by developing spectral climatology for tide gauge and altimetry data. Power spectral density analysis is applied to detect the magnitude of ocean tides in 20 years of sea-level data from multimission satellite altimeters and tide gauges. The spectra of altimetry sea level anomaly (SLA) time series have their strongest peaks centred at approximately 2.11, 5.88, and 7.99 cycles per year (cpy), corresponding to the diurnal and semidiurnal tidal constituents K1, M2, and O1, respectively. Closer to the coastline, the spectra peak at high-frequency overtide and shallow-water constituents such as M4, MK4, and MK3. There have been many large, high-frequency spectral peaks near the coastline, indicating the difficulty of predicting tidal signals by coastal altimetry. Similar to altimetry observations, there are dominant semidiurnal and diurnal tidal peaks in tide gauge SLA time series accompanying a number of overtides. The semidiurnal and diurnal peaks are mostly higher on the northwest coast of Australia compared with the north and northeast coast. The results from both altimetry and tide gauges indicate that tidal range increases with increasing continental shelf.

Estimating contribution of high-frequency sea-level oscillations to the extreme sea levels in the Adriatic Sea

2021 ◽  
Author(s):  
Krešimir Ruić ◽  
Jadranka Šepić ◽  
Maja Karlović ◽  
Iva Međugorac
Keyword(s):  
Time Series ◽  
Sea Level ◽  
High Frequency ◽  
Adriatic Sea ◽  
Tide Gauge ◽  
Data Series ◽  
Sea Levels ◽  
Short Period ◽  
Extreme Sea Levels ◽  
Sea Level Oscillations

<p>Extreme sea levels are known to hit the Adriatic Sea and to occasionally cause floods that produce severe material damage. Whereas the contribution of longer-period (T > 2 h) sea-level oscillations to the phenomena has been well researched, the contribution of the shorter period (T < 2 h) oscillations is yet to be determined. With this aim, data of 1-min sampling resolution were collected for 20 tide gauges, 10 located at the Italian (north and west) and 10 at the Croatian (east) Adriatic coast. Analyses were done on time series of 3 to 15 years length, with the latest data coming from 2020, and with longer data series available for the Croatian coast. Sea level data were thoroughly checked, and spurious data were removed. </p><p>For each station, extreme sea levels were defined as events during which sea level surpasses its 99.9 percentile value. The contribution of short-period oscillations to extremes was then estimated from corresponding high-frequency (T < 2 h) series. Additionally, for four Croatian tide gauge stations (Rovinj, Bakar, Split, and Dubrovnik), for period of 1956-2004, extreme sea levels were also determined from the hourly sea level time series, with the contribution of short-period oscillations visually estimated from the original tide gauge charts.  </p><p>Spatial and temporal distribution of contribution of short-period sea-level oscillations to the extreme sea level in the Adriatic were estimated. It was shown that short-period sea-level oscillation can significantly contribute to the overall extremes and should be considered when estimating flooding levels. </p>

scholarly journals Recent sea level rise on Ireland's east coast based on multiple tide gauge analysis

2020 ◽  
Author(s):  
Amin Shoari Nejad ◽  
Andrew C. Parnell ◽  
Alice Greene ◽  
Brian P. Kelleher ◽  
Gerard McCarthy
Keyword(s):  
Time Series ◽  
Sea Level Rise ◽  
Sea Level ◽  
Continuous Time ◽  
East Coast ◽  
Tide Gauge ◽  
Tide Gauges ◽  
Missing Value ◽  
Global Average ◽  
Good Agreement

Abstract. We analysed multiple tide gauges from the east coast of Ireland over the period 1938–2018. We validated the different time series against each other and performed a missing value imputation exercise, which enabled us to produce a homogenised record. The recordings of all tide gauges were found to be in good agreement between 2003–2015, though this was markedly less so from 2016 to the present. We estimate the sea level rise in Dublin port for this period at 10 mm yr−1. The rate over the longer period of 1938–2015 was 1.67 mm yr−1 which is in good agreement with the global average. We found that the rate of sea level rise in the longer term record is cyclic with some extreme upward and downward trends. However, starting around 1980, Dublin has seen significantly higher rates that have been always positive since 1996, and this is mirrored in the surrounding gauges. Furthermore, our analysis indicates an increase in sea level variability since 1980. Both decadal rates and continuous time rates are calculated and provided with uncertainties in this paper.

scholarly journals Sinking Tide Gauge Revealed by Space-borne InSAR: Implications for Sea Level Acceleration at Pohang, South Korea

2019 ◽  
Vol 11 (3) ◽  
pp. 277 ◽  
Author(s):  
Suresh Palanisamy Vadivel ◽  
Duk-jin Kim ◽  
Jungkyo Jung ◽  
Yang-Ki Cho ◽  
Ki-Jong Han ◽  
...  
Keyword(s):  
Sea Level Rise ◽  
Sea Level ◽  
Tide Gauge ◽  
Tide Gauges ◽  
Tide Gauge Records ◽  
Relative Sea Level ◽  
Tide Gauge Station ◽  
Sea Level Acceleration ◽  
Vertical Land Motion ◽  
Gauge Station

Vertical land motion at tide gauges influences sea level rise acceleration; this must be addressed for interpreting reliable sea level projections. In recent years, tide gauge records for the Eastern coast of Korea have revealed rapid increases in sea level rise compared with the global mean. Pohang Tide Gauge Station has shown a +3.1 cm/year sea level rise since 2013. This study aims to estimate the vertical land motion that influences relative sea level rise observations at Pohang by applying a multi-track Persistent Scatter Interferometric Synthetic Aperture Radar (PS-InSAR) time-series analysis to Sentinel-1 SAR data acquired during 2015–2017. The results, which were obtained at a high spatial resolution (10 m), indicate vertical ground motion of −2.55 cm/year at the Pohang Tide Gauge Station; this was validated by data from a collocated global positioning system (GPS) station. The subtraction of InSAR-derived subsidence rates from sea level rise at the Pohang Tide Gauge Station is 6 mm/year; thus, vertical land motion significantly dominates the sea level acceleration. Natural hazards related to the sea level rise are primarily assessed by relative sea level changes obtained from tide gauges; therefore, tide gauge records should be reviewed for rapid vertical land motion along the vulnerable coastal areas.

scholarly journals Validation of Copernicus Sea Level Altimetry Products in the Baltic Sea and Estonian Lakes

2020 ◽  
Vol 12 (24) ◽  
pp. 4062
Author(s):  
Aive Liibusk ◽  
Tarmo Kall ◽  
Sander Rikka ◽  
Rivo Uiboupin ◽  
Ülo Suursaar ◽  
...  
Keyword(s):  
Baltic Sea ◽  
Sea Level ◽  
Tide Gauge ◽  
Tide Gauges ◽  
The Baltic Sea ◽  
Geoid Model ◽  
Temporal Sampling ◽  
Level 3 ◽  
The Baltic ◽  
Level 2

Multi-mission satellite altimetry (e.g., ERS, Envisat, TOPEX/Poseidon, Jason) data have enabled a synoptic-scale view of ocean variations in past decades. Since 2016, the Sentinel-3 mission has provided better spatial and temporal sampling compared to its predecessors. The Sentinel-3 Ku/C Radar Altimeter (SRAL) is one of the synthetic aperture radar altimeters (SAR Altimeter) which is more precise for coastal and lake observations. The article studies the performance of the Sentinel-3 Level-2 sea level altimetry products in the coastal areas of the Baltic Sea and on two lakes of Estonia. The Sentinel-3 data were compared with (i) collocated Global Navigation Satellite System (GNSS) ship measurements, (ii) the Estonian geoid model (EST-GEOID2017) together with sea-level anomaly corrections from the tide gauges, and (iii) collocated buoy measurements. The comparisons were carried out along seven Sentinel-3A/B tracks across the Baltic Sea and Estonian lakes in 2019. In addition, the Copernicus Marine Environment Monitoring Service (CMEMS) Level-3 sea-level products and the Nucleus for European Modelling of the Ocean (NEMO) reanalysis outcomes were compared with measurements from Estonia’s 21 tide gauges and the buoy deployed offshore. Our results showed that the uncertainty of the Sentinel-3 Level-2 altimetry product was below decimetre level for the seacoast and the selected lakes of Estonia. Results from CMEMS Level-3 altimetry products showed a correlation of 0.83 (RMSE 0.18 m) and 0.91 (RMSE 0.27 m) when compared against the tide gauge measurements and the NEMO model, respectively. The overall performance of the altimetry products was very good, except in the immediate vicinity of the coastline and for the lakes, where the accuracy was nearly three times lower than for the open sea, but still acceptably good.

scholarly journals Sea level trend and variability around Peninsular Malaysia

Ocean Science ◽  
2015 ◽  
Vol 11 (4) ◽  
pp. 617-628 ◽  
Author(s):  
Q. H. Luu ◽  
P. Tkalich ◽  
T. W. Tay
Keyword(s):  
Sea Level Rise ◽  
Sea Level ◽  
Satellite Altimetry ◽  
Tide Gauge ◽  
Peninsular Malaysia ◽  
Tide Gauges ◽  
Tide Gauge Records ◽  
Regional Sea Level ◽  
Malacca Strait ◽  
Singapore Strait

Abstract. Sea level rise due to climate change is non-uniform globally, necessitating regional estimates. Peninsular Malaysia is located in the middle of Southeast Asia, bounded from the west by the Malacca Strait, from the east by the South China Sea (SCS), and from the south by the Singapore Strait. The sea level along the peninsula may be influenced by various regional phenomena native to the adjacent parts of the Indian and Pacific oceans. To examine the variability and trend of sea level around the peninsula, tide gauge records and satellite altimetry are analyzed taking into account vertical land movements (VLMs). At annual scale, sea level anomalies (SLAs) around Peninsular Malaysia on the order of 5–25 cm are mainly monsoon driven. Sea levels at eastern and western coasts respond differently to the Asian monsoon: two peaks per year in the Malacca Strait due to South Asian–Indian monsoon; an annual cycle in the remaining region mostly due to the East Asian–western Pacific monsoon. At interannual scale, regional sea level variability in the range of ±6 cm is correlated with El Niño–Southern Oscillation (ENSO). SLAs in the Malacca Strait side are further correlated with the Indian Ocean Dipole (IOD) in the range of ±5 cm. Interannual regional sea level falls are associated with El Niño events and positive phases of IOD, whilst rises are correlated with La Niña episodes and negative values of the IOD index. At seasonal to interannual scales, we observe the separation of the sea level patterns in the Singapore Strait, between the Raffles Lighthouse and Tanjong Pagar tide stations, likely caused by a dynamic constriction in the narrowest part. During the observation period 1986–2013, average relative rates of sea level rise derived from tide gauges in Malacca Strait and along the east coast of the peninsula are 3.6±1.6 and 3.7±1.1 mm yr−1, respectively. Correcting for respective VLMs (0.8±2.6 and 0.9±2.2 mm yr−1), their corresponding geocentric sea level rise rates are estimated at 4.4±3.1 and 4.6±2.5 mm yr−1. The geocentric rates are about 25 % faster than those measured at tide gauges around the peninsula; however, the level of uncertainty associated with VLM data is relatively high. For the common period between 1993 and 2009, geocentric sea level rise values along the Malaysian coast are similar from tide gauge records and satellite altimetry (3.1 and 2.7 mm yr−1, respectively), and arguably correspond to the global trend.

scholarly journals Using continuous GPS and absolute gravity to separate vertical land movements and changes in sea-level at tide-gauges in the UK

2006 ◽  
Vol 364 (1841) ◽  
pp. 917-930 ◽  
Author(s):  
F.N Teferle ◽  
R.M Bingley ◽  
S.D.P Williams ◽  
T.F Baker ◽  
A.H Dodson
Keyword(s):  
Time Series ◽  
Sea Level ◽  
Tide Gauge ◽  
Absolute Gravity ◽  
Tide Gauges ◽  
Tide Gauge Record ◽  
Vertical Movements ◽  
Movement Component ◽  
The Uk ◽  
Continuous Gps

Researchers investigating climate change have used historical tide-gauge measurements from all over the world to investigate the changes in sea-level that have occurred over the last century or so. However, such estimates are a combination of any true sea-level variations and any vertical movements of the land at the specific tide-gauge. For a tide- gauge record to be used to determine the climate related component of changes in sea-level, it is therefore necessary to correct for the vertical land movement component of the observed change in sea-level. In 1990, the Institute of Engineering Surveying and Space Geodesy and Proudman Oceanographic Laboratory started developing techniques based on the Global Positioning System (GPS) for measuring vertical land movements (VLM) at tide-gauges in the UK. This paper provides brief details of these early developments and shows how they led to the establishment of continuous GPS (CGPS) stations at a number of tide-gauges. The paper then goes on to discuss the use of absolute gravity (AG), as an independent technique for measuring VLM at tide-gauges. The most recent results, from CGPS time-series dating back to 1997 and AG time-series dating back to 1995/1996, are then used to demonstrate the complementarity of these two techniques and their potential for providing site-specific estimates of VLM at tide-gauges in the UK.

Sign in / Sign up

Export Citation Format

Share Document