scholarly journals AA2219 Aluminum Alloy Processed via Multi-Axial Forging in Cryogenic and Ambient Environments

2019 ◽  
Vol 8 (2) ◽  
pp. 1 ◽  
Author(s):  
Amin Azimi ◽  
Gbadebo Moses Owolabi ◽  
Hamid Fallahdoost ◽  
Nikhil Kumar ◽  
Horace Whitworth ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Room Temperature ◽  
Tensile Tests ◽  
Second Phase ◽  
X Ray Diffraction ◽  
Transmission Electron Microscopy Micrographs ◽  
Transmission Electron ◽  
Second Phase Particles ◽  
Aa2219 Aluminum Alloy ◽  
Cryogenic Processing

This paper presents the microstructure and the mechanical behavior of nanocrystalline AA2219 processed by multi axial forging (MAF) at ambient and cryogenic temperatures. The X-ray diffraction pattern and transmission electron microscopy micrographs in the initial microstructure characterization indicate a more effective severe plastic deformation during the cryogenic MAF than the same process conducted at room temperature. MAF at cryogenic temperature results in crystallite size reduction to nanoscales as well as second phase particles breakage to finer particles which are the crucial factors to increasing the mechanical properties of the material. Fractography analysis and tensile tests results show that cryogenic forging does not only increase the mechanical strength and toughness of the alloys significantly, but also improves the ductility of the material in comparison with the conventional forging. In this comparative regard, cryogenic processing provides 44% increase in the tensile strength of the material only after 2 forging cycles when compared to the room temperature process. In addition, further forging process to the next cycles slightly enhances the tensile strength at the expense of ductility due to less ability of the dislocations to accumulate. However, the ductility of the ambient temperature forged samples decreases at a faster rate than that of cryoforged samples.

Effect of Second Phase Particles on the Tensile Instability of a Nanostructured Al-1%Si Alloy

2014 ◽  
Vol 783-786 ◽  
pp. 2629-2634 ◽  
Author(s):  
Tian Lin Huang ◽  
Gui Lin Wu ◽  
Qing Liu ◽  
Xiao Xu Huang
Keyword(s):  
Tensile Tests ◽  
Structural Features ◽  
Second Phase ◽  
Commercial Purity ◽  
Localized Deformation ◽  
Dispersed Particles ◽  
Transmission Electron ◽  
Second Phase Particles ◽  
Tensile Instability ◽  
Recovery Annealing

A nanostructured Al-1%Si alloy containing dispersed Si particles was produced by heavily cold-rolling to study the effect of second phase particles on the tensile instability of nanostructured metals. Tensile tests were conducted on the as-deformed sample and the samples after recovery annealing treatments. The structural features of deformed and annealed samples were characterized by transmission electron microscopy. By comparing with the behavior of nanostructured commercial purity Al without dispersed particles, a remarked improvement in the tensile stability was found. This is related to a prevention of localized deformation by the presence of finely dispersed Si particles in the nanoscale matrix structure.

Study on the Preparation and Micro Structure of the Mg Containing Porous HA with Ultra-Fine Grain

2009 ◽  
Vol 610-613 ◽  
pp. 1132-1136
Author(s):  
Xing Yi Li ◽  
Xiang Cai Meng ◽  
Guo Quan Liu ◽  
Shi Dan Yuan
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Chemical Precipitation ◽  
Second Phase ◽  
X Ray Diffraction ◽  
Micro Structure ◽  
X Ray ◽  
Fine Grain ◽  
Transmission Electron ◽  
Second Phase Particles

The Nano-HA powder were synthesized by chemical precipitation with Ca(H2PO4)2•H2O and Ca (OH)2 and porous HA was prepared by sintering with magnesium as pore-creator. Nano-HA powder and porous HA were characterized by wide angle X-ray diffraction, transmission electron microscopy(TEM), scanning electron microscopy (SEM), SEM in combination with energy dispersive X-ray spectroscopy (SEM-EDX), X-ray photoelectron spectroscopy. The experimental results show that HA powder synthesized by chemical precipitation is nanometer powder. Magnesium was ideal pore-creator for preparation of porous materials. The grain size of porous HA was sub-micron and MgO which existed in the grain boundary of HA as a second phase particles that played the roles of inhibiting the HA grain growth.

Microstructure analysis of GdBa2Cu3O7-δ coated conductors by the RCE-DR process

2012 ◽  
Vol 1434 ◽  
Author(s):  
Soon-Mi Choi ◽  
Jung-Woo Lee ◽  
Seung-Hyun Moon ◽  
Sang-Im Yoo
Keyword(s):  
Buffer Layer ◽  
Process Analysis ◽  
Thick Layer ◽  
Coated Conductors ◽  
Second Phase ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Second Phase Particles ◽  
Crystallographic Orientation Relationship ◽  
O Phase

ABSTRACTWe report the microstructural features of GdBa2Cu3O7-δ (GdBCO) coated conductors (CCs) on LaMnO3 (LMO)-buffered IBAD MgO template, produced by the Reactive Co-Evaporation Deposition & Reaction (RCE-DR) process. Analysis results by X-ray diffraction (XRD) and transmission electron microscopy (TEM) revealed that a lot of elongated round second phase particles of 70-150nm size within the GdBCO matrix were the Gd2O3 phase, a small amount of Cu-O phase were also trapped in the GdBCO matrix, and a thick layer of Cu-excessive Ba-Cu-O phase was found on the top surface of the GdBCO film, suggesting that the GdBCO film might be grown from Gd2O3 and liquid phase by a peritectic recombination. While both the GdBCO film and some Gd2O3 particles grown on the LMO-buffer layer were biaxially textured, the Gd2O3 particles fully trapped in the GdBCO matrix were randomly oriented. The Gd2O3 particles located at the interface between the GdBCO and LMO buffer layer exhibited the following crystallographic orientation relationship: LMO [010] // GdBCO [010] // Gd2O3 [110]; LMO [001] // GdBCO [001] // Gd2O3 [001].

Analytical Microscopic Analysis of Precipitates in Hastelloy Alloy C-276

1981 ◽  
Vol 39 ◽  
pp. 280-281
Author(s):  
M. Raghavan ◽  
B. J. Berkowitz ◽  
J. C. Scanlon
Keyword(s):  
Microscopic Analysis ◽  
Scanning Transmission Electron Microscope ◽  
Second Phase ◽  
Precipitation Reaction ◽  
X Ray Diffraction ◽  
Corrosion Properties ◽  
X Ray ◽  
Transmission Electron ◽  
Second Phase Particles ◽  
Scanning Transmission

The present investigation was conducted to characterize the second phase particles in Hastelloy C-276 using an analytical Scanning Transmission Electron Microscope in order to understand their effect on the mechanical and Stress Corrosion properties of the alloy. Investigation in our 1aboratoryO) and previous published reports(2-4) have identified two types of precipitation reactions in this alloy. At temperatures in the range of 300-650°C, the alloy precipitates an ordered phase of the type Ni2(Cr, Mo)(1,2). This precipitation reaction is homogeneous with no preferential precipitation at the grain boundaries or twin boundaries. At temperatures above 650°C, several precipitate phases were observed to nucleate heterogeneously at boundaries and using X-ray diffraction techniques, the precipitates were previously identified as the μ, M6C and P phases(3-4). The present investigation was carried out to determine the composition of these second phase particles and this article describes the characterization of these precipitates using X-ray microanalysis and microdiffraction techniques.

The Mechanical Properties of the Mo-0.5Ti and Mo-0.1Zr Alloys at Room Temperature and High Temperature Annealing

2017 ◽  
Vol 36 (2) ◽  
pp. 167-173 ◽  
Author(s):  
Chaopeng Cui ◽  
Yimin Gao ◽  
Shizhong Wei ◽  
Guoshang Zhang ◽  
Yucheng Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Alloy Element ◽  
Second Phase ◽  
High Temperature Annealing ◽  
Molybdenum Alloys ◽  
Second Phase Particles ◽  
Strength And Plasticity

AbstractMo-0.5Ti and Mo-0.1Zr alloys were prepared by powder metallurgy. In Mo-0.5Ti and Mo-0.1Zr alloys, there appears the second-phase particles of Ti2O3 and ZrO2 respectively, each of which can effectively prevent the dislocation activity in the process of plastic deformation. The addition of Zr can increase the strength of molybdenum alloys. Meanwhile, the ZrO2 formed from the alloy element Zr can refine the grains of molybdenum alloys to improve the recrystallization plasticity. After annealing, the tensile strength decreases while the plasticity greatly increases compared to the annealed Mo-0.5Ti and Mo-0.1Zr alloys. With the increase of annealing temperature, both the tensile strength and plasticity of Mo-0.5Ti and Mo-0.1Zr alloys decrease. Compared with pure Mo, after annealing the properties of the Mo-0.5Ti alloy and the plasticity of the Mo-0.1Zr alloy significantly increases.

Effects of Trace ZrC on the Microstructure and Properties of Molybdenum Alloy

2013 ◽  
Vol 785-786 ◽  
pp. 76-80
Author(s):  
Hui Chao Cheng ◽  
Jing Lian Fan ◽  
Zhao Qian ◽  
Jia Min Tian
Keyword(s):  
Tensile Strength ◽  
High Temperature ◽  
Room Temperature ◽  
Tensile Fracture ◽  
Second Phase ◽  
Powder Metallurgy Method ◽  
Microstructure And Properties ◽  
Dimple Fracture ◽  
Second Phase Particles ◽  
Zr Alloy

The present study describes the effect of trace ZrC additive on the microstructure and properties of Mo-Ti-Zr alloy fabricated by powder metallurgy method. The results indicate that, ZrC addition effectively enhanced the tensile strength of the alloy both at room-temperature and high-temperature, the alloy with 0.4wt% ZrC has the highest tensile strength, which is 611MPa and 513MPa at 25°C and 800°C, respectively. The tensile fracture mainly consists of intergranular rupture at room temperature, while dimple fracture occurred at high temperature, which indicating higher elongation. Through observation from the micrograph and EDS analysis, ZrxOyCz second-phase particles were observed,which is derived from part of ZrC particles reacted with the oxygen and can suppress the oxygen segregation on grain boundary.

Brittle cleavage of L12 trialuminides

1990 ◽  
Vol 5 (8) ◽  
pp. 1639-1648 ◽  
Author(s):  
E. P. George ◽  
J. A. Horton ◽  
W. D. Porter ◽  
J. H. Schneibel
Keyword(s):  
Room Temperature ◽  
Crack Nucleation ◽  
Cleavage Plane ◽  
Second Phase ◽  
Cleavage Crack ◽  
Transgranular Cleavage ◽  
Transmission Electron ◽  
Nucleation Sites ◽  
Second Phase Particles ◽  
Cleavage Strength

Three trialuminide alloys, binary Al–25Sc, ternary Al–25Zr–6Fe, and quaternary Al–23Ti–6Fe–5V, all having the cubic L12 structure, were investigated. All three alloys fracture in a brittle manner (fracture toughness, 2–3 MPa m½), predominantly by transgranular cleavage. Of nineteen cleavage facets examined in binary Al3Sc, seventeen were of the {110} type and only two were of the {100} type, consistent with our earlier work which showed that the cleavage plane occurring most frequently in quaternary Al–23Ti–6Fe–5V is also {110}. The room-temperature hardnesses and yield strengths (100–200 DPH and 100–270 MPa, respectively) of all three alloys are quite low (comparable to ductile L12 alloys like Ni3Al), indicating that there is significant dislocation activity in these materials. Consistent with this, transmission electron microscopy identified several APB-coupled dislocations with b - a/2〈110〉 gliding on the {111} planes in both binary Al–25Sc and quaternary Al–23Ti–6Fe–5V. The separations between the superpartials in Al–25Sc and Al–23Ti–6Fe–5V were measured to be 3.7 and 4 nm, respectively, giving APB energies of 313 and 274 mJ/m2, respectively. Auger analyses failed to detect any impurities on the cleavage facets themselves, or on second phase particles (or other potential cleavage crack nucleation sites). It is therefore concluded that brittle fracture in these alloys is not impurity-induced. Based on all the results obtained to date we conclude that the unusual brittleness of L12 trialuminides is related to their intrinsically low cleavage strength. Possible reasons for their low cleavage strength are discussed.

Photoluminescence Enhancement of CdS Nanocrystals Fabricated on Dithiocarbamate Functionalized PET Substrates

2012 ◽  
Vol 512-515 ◽  
pp. 1511-1515
Author(s):  
Chun Lin Zhao ◽  
Li Xing ◽  
Xiao Hong Liang ◽  
Jun Hui Xiang ◽  
Fu Shi Zhang ◽  
...  
Keyword(s):  
Room Temperature ◽  
Hexagonal Structure ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
Visible Absorption ◽  
X Ray ◽  
Cds Nanocrystals ◽  
Morphological Studies ◽  
Transmission Electron

Cadmium sulfide (CdS) nanocrystals (NCs) were self-assembled and in-situ immobilized on the dithiocarbamate (DTCs)-functionalized polyethylene glycol terephthalate (PET) substrates between the organic (carbon disulfide diffused in n-hexane) –aqueous (ethylenediamine and Cd2+ dissolved in water) interface at room temperature. Powder X-ray diffraction measurement revealed the hexagonal structure of CdS nanocrystals. Morphological studies performed by scanning electron microscopy (SEM) and high-resolution transmission electron microscope (HRTEM) showed the island-like structure of CdS nanocrystals on PET substrates, as well as energy-dispersive X-ray spectroscopy (EDS) confirmed the stoichiometries of CdS nanocrystals. The optical properties of DTCs modified CdS nanocrystals were thoroughly investigated by ultraviolet-visible absorption spectroscopy (UV-vis) and fluorescence spectroscopy. The as-prepared DTCs present intrinsic hydrophobicity and strong affinity for CdS nanocrystals.

scholarly journals Facile Organometallic Synthesis of Fe-Based Nanomaterials by Hot Injection Reaction

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1141
Author(s):  
Georgia Basina ◽  
Hafsa Khurshid ◽  
Nikolaos Tzitzios ◽  
George Hadjipanayis ◽  
Vasileios Tzitzios
Keyword(s):  
Room Temperature ◽  
Colloidal Particles ◽  
Iron Pentacarbonyl ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
Organometallic Synthesis ◽  
X Ray ◽  
Transmission Electron ◽  
Hot Injection ◽  
The Stability

Fe-based colloids with a core/shell structure consisting of metallic iron and iron oxide were synthesized by a facile hot injection reaction of iron pentacarbonyl in a multi-surfactant mixture. The size of the colloidal particles was affected by the reaction temperature and the results demonstrated that their stability against complete oxidation related to their size. The crystal structure and the morphology were identified by powder X-ray diffraction and transmission electron microscopy, while the magnetic properties were studied at room temperature with a vibrating sample magnetometer. The injection temperature plays a very crucial role and higher temperatures enhance the stability and the resistance against oxidation. For the case of injection at 315 °C, the nanoparticles had around a 10 nm mean diameter and revealed 132 emu/g. Remarkably, a stable dispersion was created due to the colloids’ surface functionalization in a nonpolar solvent.

Structural, Morphological, Magnetic and Self-Heating Studies of One-Step Polyol Synthesized Manganese Ferrite (MnFe2O4) Nanoparticles

2019 ◽  
Vol 19 (01) ◽  
pp. 1950003
Author(s):  
P. R. Ghutepatil ◽  
S. H. Pawar
Keyword(s):  
Room Temperature ◽  
Synthesis Method ◽  
Average Crystallite Size ◽  
Superparamagnetic Nanoparticles ◽  
Polyol Synthesis ◽  
X Ray Diffraction ◽  
Self Heating ◽  
Transmission Electron ◽  
One Step ◽  
Mnfe2o4 Nanoparticles

In this paper, uniform and superparamagnetic nanoparticles have been prepared using one-step polyol synthesis method. Structural, morphological and magnetic properties of obtained MnFe2O4 nanoparticles have been investigated by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), vibrating sample magnetometry (VSM) and thermogravimetric analysis (TGA) techniques. Structural investigation showed that the average crystallite size of obtained nanoparticles was about 10[Formula: see text]nm. Magnetic study revealed that the nanoparticles were superparamagnetic at room temperature with magnetization 67[Formula: see text]emu/g at room temperature. The self-heating characteristics of synthesized MnFe2O4 nanoparticles were studied by applying external AC magnetic field of 167.6 to 335.2[Formula: see text]Oe at a fixed frequency of 265[Formula: see text]kHz. The SAR values of MnFe2O4 nanoparticles were calculated for 2, 5, 10[Formula: see text]mg[Formula: see text]mL[Formula: see text] concentrations and it is observed that the threshold hyperthermia temperature is achieved for all concentrations.

Sign in / Sign up

Export Citation Format

Share Document