Effect of Nitrate/Bromide on the Hydration Process of Cement Paste Mixed with Alkali Free Liquid Accelerator at Low Temperature

The effects of different inorganic salt accelerators (CaBr2, NaBr, Ca(NO3)2, NaNO3) and an alkali-free liquid accelerator were researched at a low temperature of 10 °C. The results showed the effects of 1.5% NaBr and 1.5% NaNO3 inorganic accelerator were pronounced. The 1-d compressive strengths of the mortar with these two inorganic salts were increased by 185.8% and 184.2%, respectively, and the final setting times were shortened from 7.74 to 6.08 min and 6.12 min, respectively. The hydration temperatures at 10 °C were measured, and the promotion effects of the inorganic accelerators were calculated: the relationship between the hydration degree was αAS + NN > αAS + NB > αAS + CB > αAS + CN > αAS. In addition, the reaction of C3A with NaBr and NaNO3 was used to analyze the products in an ettringite phase, i.e., Ca4Al2O6Br210·H2O, 3CaOAl2O3Ca(NO3)2X·H2O. The formation of these phases was detected in the hydration products of the cement paste hydration for 12 h, 24 h, and 28 d. Combined with the mass loss of the ettringite phase at 90–120 °C, determined using TG/DTG, the synergetic acceleration mechanism of the inorganic accelerators was comprehensively inferred.

On saline infusion, clonus, molecules and forgotten scientists: Who was Dr Julius Sander (1840–1909)?

Zitterbewegungen des Fusses bei Dorsalflexion (shaking movements of the foot upon dorsal flexion) were observed independently from each other and described in the same issue of a German peer reviewed journal by Carl Westphal (1833–1890) at the Charité in Berlin and by Wilhelm Erb (1840–1921) in Heidelberg. While Westphal used the term Fussphaenomen, Erb is credited with coining the term clonus for the phenomenon. Both scientists are immortalized by various eponyms acknowledging their respective contributions to science. Little is known however about Julius Sander (1840–1909), in those days resident at Charité, who noticed the phenomenon and presented it to his superiors, Wilhelm Griesinger (1817 −1868) and Westphal. In addition to such observations, Sander made original contributions in resuscitation physiology while working with Hugo Kronecker (1839–1914). With Kronecker, Sander published observations on life saving transfusions with inorganic salt solutions in dogs “ Bemerkung über lebensrettende Transfusion mit anorganischer Salzlösung bei Hunden” a very early work on isovolemic fluid resuscitation. The purpose of this communication is to highlight Sander's scientific contributions and to shed some light on his life, of which a German Lexicon stated that after 1870 no information on him can be ascertained anymore.

Strong Viscosity Increase in Aqueous Solutions of Cationic C22-Tailed Surfactant Wormlike Micelles

The viscoelastic properties and structure parameters have been investigated for aqueous solutions of wormlike micelles of cationic surfactant erucyl bis(hydroxyethyl) methylammonium chloride with long C22 tail in the presence inorganic salt KCl. The salt content has been varied to estimate linear to branched transition conditions due to screening of the electrostatic interaction in the networks. The local cylindrical structure and low electrostatic repulsion was obtained by SANS data. The drastic power law dependencies of rheological properties on surfactant concentrations were obtained at intermediate salt content. Two power law regions were detected in semi-dilute solutions related to “unbreakable” and “living” micellar chains. The fast contour length growth with surfactant concentration was demonstrated that is in good agreement with theoretical predictions.

The Effect of Inorganic Salt on the Morphology and Nucleation of Polyaniline

Polyaniline nanofibers were fabricated through the addition of inorganic salt such as NaCl, MgSO4 and AlCl3 into the micelle-like composed of aniline and camphor sulfonic acid (CSA). The influence of types and concentration of inorganic salts, doped acids and temperature on polyaniline was studied by TEM, Uv-vis and FTIR spectroscopy. In addition, in situ Uv-vis and 1H NMR were applied to observe the process of aniline polymerization, and it was indicated the polymerization rate of aniline changed after the addition of inorganic salt NaCl into the initial solution.

Ecotoxicity of binary mixtures of ILs and inorganic salts of electrochemical interest

The applicability of ionic liquids (ILs) has increased over the last years, and even new opportunities are becoming a reality, i.e. mixtures of pure IL and inorganic salt as electrolytes for smart electrochemical devices, yet the effects on the environment are almost unknown. In this work, the ecotoxicity of two pure protic ILs (Ethylammonium nitrate and Ethylimidazolium nitrate) and two pure aprotic ILs (butylmethylpyrrolidinium bis(trifluoromethylsulfonyl)imide and butyldimethylimidazolium bis(trifluoromethylsulfonyl)imide) and that of their binary mixtures with inorganic salts with common cation was tested towards changes in the bioluminescence of the bacteria Aliivibrio fischeri, using the Microtox® standard toxicity test. EC50 of these mixtures was determined over three standard periods of time and compared with the corresponding values to pure ILs. Results indicate that the aprotic ILs are more toxic than protic and that aromatic are more toxic than non-aromatic. The addition of inorganic mono (LiNO3), di (Ca(NO3)2·4H2O, Mg(NO3)2·6H2O) and trivalent (Al(NO3)3·9H2O) salts in binary mixtures with EAN was analysed first. The latter was found to induce an important increase in toxicity. Finally, mixtures of IL-inorganic lithium salt (LiNO3, for the protic ILs and LiTFSI for the aprotic ILs) toxicity was also studied, which showed toxicity levels strongly dependent on the IL of the mixture.

The Effect of AlI3 Nanoadditive on the Thermal Behavior of PMMA Subjected to Thermoanalytical Py-GC-MS Technique

Thermal degradation of polymethylmethacrylate (PMMA) was studied by using inorganic salt of aluminum triiodide (AlI3). The composites of PMMA were prepared with AlI3 by changing the concentration of the AlI3 additive from 2% to 10% (w/w). The PMMA composites with AlI3 were characterized by TGA, DTG, SEM, FTIR, HBT, and Py-GC-MS techniques. The FTIR peaks of PMMA composite at 1316, 786, and 693 cm−1 justify the chemical association between PMMA and AlI3. TGA study shows that the stability of PMMA is enhanced by the addition of the AlI3 additive. SEM analysis represented that there is a relationship between polymer and additive when they are mixed at the molecular level. The horizontal burning test (HBT) also confirmed that the AlI3 additive produced the flame retarding properties in PMMA polymer. The burning rate of composite with 10% of AlI3 additive decreases five times as much as compared to pure PMMA polymer. Py-GC-MS analysis deduced that PMMA composite produced less toxic and environment-friendly substances (CO2) by the influence of AlI3 additive as compared to neat PMMA.