scholarly journals Influence of Large Relative Tip Clearances for a Micro Radial Fan and Design Guidelines for Increased Efficiency

2020 ◽  
Author(s):  
Patrick H. Wagner ◽  
Jan Van herle ◽  
Lili Gu ◽  
Jürg Schiffmann
Keyword(s):  
Pressure Rise ◽  
Leading Edge ◽  
High Sensitivity ◽  
Design Guidelines ◽  
Tip Clearance ◽  
Small Scale ◽  
Blade Tip ◽  
Dynamics Simulations ◽  
Experimental Findings ◽  
Blade Tip Clearance

Abstract The blade tip clearance loss was studied experimentally and numerically for a micro radial fan with a tip diameter of 19.2mm. Its relative blade tip clearance, i.e., the clearance divided by the blade height of 1.82 mm, was adjusted with different shims. The fan characteristics were experimentally determined for an operation at the nominal rotational speed of 168 krpm with hot air (200 °C). The total-to-total pressure rise and efficiency increased from 49 mbar to 68 mbar and from 53% to 64%, respectively, by reducing the relative tip clearance from 7.7% to the design value of 2.2%. Single and full passage computational fluid dynamics simulations correlate well with these experimental findings. The widely-used Pfleiderer loss correlation with an empirical coefficient of 2.8 fits the numerical simulation and the experiments within +2 efficiency points. The high sensitivity to the tip clearance loss is a result of the design specific speed of 0.80, the highly-backward curved blades (17°), and possibly the low Reynolds number (1 × 105). The authors suggest three main measures to mitigate the blade tip clearance losses for small-scale fans: (1) utilization of high-precision surfaced-grooved gas-bearings to lower the blade tip clearance, (2) a mid-loaded blade design, and (3) an unloaded fan leading edge to reduce the blade tip clearance vortex in the fan passage.

Investigation on the Turbine Blade Tip Clearance Monitoring Based on Eddy Current Pulse-Trigger Method

2016 ◽  
Author(s):  
Weimin Wang ◽  
Huajin Shao ◽  
Lifang Chen ◽  
Huibin Song
Keyword(s):  
Turbine Blade ◽  
Eddy Current ◽  
Tip Clearance ◽  
Small Scale ◽  
Test Rig ◽  
Rotating Speed ◽  
Laboratory Setup ◽  
Blade Tip ◽  
Scale Test ◽  
Blade Tip Clearance

The efficiency and reliability of turbomachinery will be improved by blade tip clearance (BTC) and blade tip timing (BTT) monitoring. Several types of sensors such as eddy-current, capacitance and optical probes are used to realize this objective. Eddy current sensor (ECS) is an ideal choice with its advantage of durablity and that it is unaffected by gas stream properties such as contamination, water vapor, and moisture. However, the bandwidth of ECS is usually less than 100 kHz, which will limit the resolution of the monitoring result. In this paper, a pulse-trigger technology based BTC method was presented. This method optimizes the static radial and circumferential calibration technology to obtain the sensitivity of the ECS in the different relative locations against the tip of blade. The information from the clearance sensor will be fused with that from the once per revolution (OPR) or key phase sensor. The method is more generally applicable in the condition where the ECS is insufficient sampling caused by the limit of narrow bandwidth, especially under the high blade tip velocity condition. A small scale and larger scale BTC measurement rig are established to validate the feasibility of this method. The small one is easy to calibrate with high accuracy and can be used to illustrate the performance of the method, while the larger scale test rig is close to real industry turbine blade. In this apparatus, the axial displacement and radial displacement of rotor vibration as well as the clearance can be monitored together so that further investigation can be conducted. Experimental research was carried out on both test rig at different rotating speed. The results show that the method presented in this paper can improve the accuracy of tip clearance monitored by ECS very well. Furthermore, this work is a proof-of-concept demonstration using a laboratory setup providing the basis for BTC active control and blade health monitoring (BHM) based on ECS.

scholarly journals Origins and Structure of Spike-Type Rotating Stall

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
G. Pullan ◽  
A. M. Young ◽  
I. J. Day ◽  
E. M. Greitzer ◽  
Z. S. Spakovszky
Keyword(s):  
Pressure Rise ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Suction Surface ◽  
Tip Leakage ◽  
Pressure Surface ◽  
Sequence Of Events ◽  
High Incidence ◽  
Experimental Findings

In this paper, we describe the structures that produce a spike-type route to rotating stall and explain the physical mechanism for their formation. The descriptions and explanations are based on numerical simulations, complemented and corroborated by experiments. It is found that spikes are caused by a separation at the leading edge due to high incidence. The separation gives rise to shedding of vorticity from the leading edge and the consequent formation of vortices that span between the suction surface and the casing. As seen in the rotor frame of reference, near the casing the vortex convects toward the pressure surface of the adjacent blade. The approach of the vortex to the adjacent blade triggers a separation on that blade so the structure propagates. The above sequence of events constitutes a spike. The computed structure of the spike is shown to be consistent with rotor leading edge pressure measurements from the casing of several compressors: the centre of the vortex is responsible for a pressure drop and the partially blocked passages associated with leading edge separations produce a pressure rise. The simulations show leading edge separation and shed vortices over a range of tip clearances including zero. The implication, in accord with recent experimental findings, is that they are not part of the tip clearance vortex. Although the computations always show high incidence to be the cause of the spike, the conditions that give rise to this incidence (e.g., blockage from a corner separation or the tip leakage jet from the adjacent blade) do depend on the details of the compressor.

The Influence of Tip Clearance on Supercritical CO2 Centrifugal Compressor Performance

2015 ◽  
Author(s):  
Hang Zhao ◽  
Qinghua Deng ◽  
Hanzhen Zhang ◽  
Zhenping Feng
Keyword(s):  
Critical Point ◽  
Supercritical Co2 ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Low Pressure ◽  
Tip Clearance ◽  
Compressor Stage ◽  
Blade Tip ◽  
Blade Tip Clearance ◽  
Blade Leading Edge

The supercritical CO2 (SCO2) compressor is the key component of the SCO2 Brayton cycle. It is considered as one of the most promising power conversion systems, because the compressor could consume small compression work as operating condition near the critical point. In this paper, a researched SCO2 compressor was designed to operate with slightly above the vapor-liquid critical point of CO2. The flow characteristics were investigated by NUMECA FINE/Turbo, coupled with the thermophysical properties of CO2 in REFPROP database. Particular attention was paid on the blade tip clearance flow characteristics. The formation and development mechanism of the blade tip low pressure regions and the parameters distributional difference were studied. Then, the effects of different blade tip clearance types on the low pressure regions of the blade leading edge tip and the aerodynamic performance of SCO2 compressor stage were compared and discussed. The combined effects of the injecting action, the blade leading edge tip shedding vortex, and the flow acceleration can lead the fluid thermodynamic state to enter the low pressure and low temperature regions at the leading edge of both the main blade and splitter blade tip. Especially, the condensation maybe exist at sharp corner of the blade tip leading edge. However, the tip clearance leakage vortex can significantly inhibit and weaken the low pressure regions. With the increase of tip clearance, the distribution and development tendency of the static pressure and temperature on the main blade leading edge tip are similar, but there is a significant influence for the splitter blades tip. Furthermore, because the tip clearance increases, the SCO2 compressor stage pressure ratio and isentropic efficiency have degraded in whole operating range, but the stable operation range is expanded. Therefore, the above comprehensive factors should be considered during the design process in order to select the suitable tip clearance shape.

Investigation on tip clearance control for the high-pressure rotor of an uncooled vaneless counter-rotating turbine

2020 ◽  
pp. 095441002095050
Author(s):  
Wei Zhao ◽  
Xiuming Sui ◽  
Kai Zhang ◽  
Zeming Wei ◽  
Qingjun Zhao
Keyword(s):  
High Pressure ◽  
Leading Edge ◽  
Back Pressure ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Trailing Edge ◽  
Blade Tip ◽  
Cooling Air ◽  
Clearance Control ◽  
Blade Tip Clearance

In order to develop a tip clearance control system for an uncooled vaneless counter-rotating turbine, tip clearance variation of its high pressure rotor blade at off-design conditions is analyzed. Aero-thermal interaction simulation is performed to predict the temperature and deformation of the solid blade. At operating conditions with rotating speeds greater than 60% design value and expansion ratios greater than 85% design value, the blade tip clearance height at leading edge remains unchanged when the expansion ratio decreases, meanwhile that at trailing edge decreased obviously. However, the tip clearance height variations at the leading edge and trailing edge are almost the same in a conventional subsonic turbine at such conditions. The cause is that the flow in the high-pressure rotor is choked at these conditions. The choked flow results in that the fluid and solid blade temperatures upstream of the throat are not affected by the back pressure and only those downstream of the throat increases with the back pressure. Consequently, the blade height at leading edge keeps constant, and that at trailing edge varies because of thermal expansion. To avoid the rubbing of the blade and case, the blade height at trailing edge is diminished by 30%. As a result, the blade tip clearance height at low speed operating conditions increases in axial direction. Such a design leads to a stronger tip leakage flow. More flow losses might be generated. Therefore, a casing cooling method is proposed to control the blade tip clearance height at leading edge and trailing edge respectively. The deformations of the casing with different mass flow rate of cooling air at design and off-design conditions are calculated. It shows that the blade tip clearance heights at leading edge and at trailing edge of the rotor can be well controlled with appropriate amount of cooling air.

scholarly journals Origins and Structure of Spike-Type Rotating Stall

2012 ◽  
Author(s):  
G. Pullan ◽  
A. M. Young ◽  
I. J. Day ◽  
E. M. Greitzer ◽  
Z. S. Spakovszky
Keyword(s):  
Pressure Rise ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Causal Connection ◽  
Suction Surface ◽  
Stall Inception ◽  
Pressure Surface ◽  
Sequence Of Events ◽  
Experimental Findings

In this paper we describe the structures that produce a spike-type route to rotating stall and explain the physical mechanism for their formation. The descriptions and explanations are based on numerical simulations, complemented and corroborated by experiments. It is found that spikes are caused by a loss of pressure rise capability in the rotor tip region, due to flow separation resulting from high incidence. The separation gives rise to shedding of vorticity from the leading edge and the consequent formation of vortices that span between the suction surface and the casing. As seen in the rotor frame of reference, near the casing the vortex convects toward the pressure surface of the adjacent blade. The approach of the vortex to the adjacent blade triggers a separation on that blade so the structure propagates. The above sequence of events constitutes a spike. The simulations show shed vortices over a range of tip clearances including zero. The implication is that they are not part of the tip clearance vortex, in accord with recent experimental findings. Evidence is presented for the existence of these vortex structures immediately prior to spike-type stall and, more strongly, for their causal connection with spike-type stall inception. Data from several compressors are shown to reproduce the pressure and velocity signature of the spike-type stall inception seen in the simulations.

A high sensitivity inductive sensor for blade tip clearance measurement

2014 ◽  
Vol 23 (6) ◽  
pp. 065018 ◽  
Author(s):  
Li Du ◽  
Xiaoliang Zhu ◽  
Jiang Zhe
Keyword(s):  
High Sensitivity ◽  
Tip Clearance ◽  
Inductive Sensor ◽  
Blade Tip ◽  
Blade Tip Clearance

scholarly journals Creep-Based Reliability Evaluation of Turbine Blade-Tip Clearance with Novel Neural Network Regression

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3552 ◽  
Author(s):  
Chun-Yi Zhang ◽  
Jing-Shan Wei ◽  
Ze Wang ◽  
Zhe-Shan Yuan ◽  
Cheng-Wei Fei ◽  
...  
Keyword(s):  
Neural Network ◽  
High Pressure ◽  
Reliability Analysis ◽  
Response Surface ◽  
Response Surface Method ◽  
Tip Clearance ◽  
Strong Nonlinearity ◽  
Surface Method ◽  
Blade Tip ◽  
Blade Tip Clearance

To reveal the effect of high-temperature creep on the blade-tip radial running clearance of aeroengine high-pressure turbines, a distributed collaborative generalized regression extremum neural network is proposed by absorbing the heuristic thoughts of distributed collaborative response surface method and the generalized extremum neural network, in order to improve the reliability analysis of blade-tip clearance with creep behavior in terms of modeling precision and simulation efficiency. In this method, the generalized extremum neural network was used to handle the transients by simplifying the response process as one extremum and to address the strong nonlinearity by means of its nonlinear mapping ability. The distributed collaborative response surface method was applied to handle multi-object multi-discipline analysis, by decomposing one “big” model with hyperparameters and high nonlinearity into a series of “small” sub-models with few parameters and low nonlinearity. Based on the developed method, the blade-tip clearance reliability analysis of an aeroengine high-pressure turbine was performed subject to the creep behaviors of structural materials, by considering the randomness of influencing parameters such as gas temperature, rotational speed, material parameters, convective heat transfer coefficient, and so forth. It was found that the reliability degree of the clearance is 0.9909 when the allowable value is 2.2 mm, and the creep deformation of the clearance presents a normal distribution with a mean of 1.9829 mm and a standard deviation of 0.07539 mm. Based on a comparison of the methods, it is demonstrated that the proposed method requires a computing time of 1.201 s and has a computational accuracy of 99.929% over 104 simulations, which are improvements of 70.5% and 1.23%, respectively, relative to the distributed collaborative response surface method. Meanwhile, the high efficiency and high precision of the presented approach become more obvious with the increasing simulations. The efforts of this study provide a promising approach to improve the dynamic reliability analysis of complex structures.

Turbine Blade Tip Clearance Measurement Instrumentation

2007 ◽  
Author(s):  
Eric B. Holmquist ◽  
Peter L. Jalbert
Keyword(s):  
Control System ◽  
Real Time ◽  
Tip Clearance ◽  
Engine Control ◽  
Operating Characteristics ◽  
Static Structure ◽  
Engine Operation ◽  
Area Of Interest ◽  
Blade Tip ◽  
Blade Tip Clearance

New and future gas turbine engines are being required to provide greater thrust with improved efficiency, while simultaneously reducing life cycle operating costs. Improved component capabilities enable active control methods to provide better control of engine operation with reduced margin. One area of interest is a means to assess the relative position of rotating machinery in real-time, in particular hot section turbo machinery. To this end, Hamilton Sundstrand is working to develop a real-time means to monitor blade position relative to the engine static structure. This approach may yield other engine operating characteristics useful in assessing component health, specifically measuring blade tip clearance, time-of-arrival, and other parameters. UTC is leveraging its many years of experience with engine control systems to develop a microwave-based sensing device, applicable to both military and commercial engines. The presentation will discuss a hot section engine demonstration of a blade position monitoring system and the control system implications posed by a microwave-based solution. Considerations necessary to implement such a system and the challenges associated with integrating a microwave-based sensor system into an engine control system are discussed.

scholarly journals Effects of Tip Clearance Gap and Exit Mach Number on Turbine Blade Tip and Near-Tip Heat Transfer

2013 ◽  
Author(s):  
K. Anto ◽  
S. Xue ◽  
W. F. Ng ◽  
L. J. Zhang ◽  
H. K. Moon
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Turbine Blade ◽  
Leading Edge ◽  
Suction Side ◽  
Tip Clearance ◽  
Pressure Side ◽  
Engine Blade ◽  
Blade Tip ◽  
Exit Mach Number

This study focuses on local heat transfer characteristics on the tip and near-tip regions of a turbine blade with a flat tip, tested under transonic conditions in a stationary, 2-D linear cascade with high freestream turbulence. The experiments were conducted at the Virginia Tech transonic blow-down wind tunnel facility. The effects of tip clearance and exit Mach number on heat transfer distribution were investigated on the tip surface using a transient infrared thermography technique. In addition, thin film gages were used to study similar effects in heat transfer on the near-tip regions at 94% height based on engine blade span of the pressure and suction sides. Surface oil flow visualizations on the blade tip region were carried-out to shed some light on the leakage flow structure. Experiments were performed at three exit Mach numbers of 0.7, 0.85, and 1.05 for two different tip clearances of 0.9% and 1.8% based on turbine blade span. The exit Mach numbers tested correspond to exit Reynolds numbers of 7.6 × 105, 9.0 × 105, and 1.1 × 106 based on blade true chord. The tests were performed with a high freestream turbulence intensity of 12% at the cascade inlet. Results at 0.85 exit Mach showed that an increase in the tip gap clearance from 0.9% to 1.8% translates into a 3% increase in the average heat transfer coefficients on the blade tip surface. At 0.9% tip clearance, an increase in exit Mach number from 0.85 to 1.05 led to a 39% increase in average heat transfer on the tip. High heat transfer was observed on the blade tip surface near the leading edge, and an increase in the tip clearance gap and exit Mach number augmented this near-leading edge tip heat transfer. At 94% of engine blade height on the suction side near the tip, a peak in heat transfer was observed in all test cases at s/C = 0.66, due to the onset of a downstream leakage vortex, originating from the pressure side. An increase in both the tip gap and exit Mach number resulted in an increase, followed by a decrease in the near-tip suction side heat transfer. On the near-tip pressure side, a slight increase in heat transfer was observed with increased tip gap and exit Mach number. In general, the suction side heat transfer is greater than the pressure side heat transfer, as a result of the suction side leakage vortices.

Sign in / Sign up

Export Citation Format

Share Document