scholarly journals Adsorption of Arsenate from Aqueous Solution onto Modified Vietnamese Bentonite

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Nguyen Le My Linh ◽  
Duc Hoang Van ◽  
Tran Duong ◽  
Mai Xuan Tinh ◽  
Dinh Quang Khieu
Keyword(s):  
Aqueous Solution ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Surface Areas ◽  
Layered Clays ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Adsorption Desorption

In this study, pillared layered clays were prepared by modifying Vietnamese bentonite with polymeric Al and Fe. The obtained materials were characteristic of X-ray diffraction analysis, thermal analysis, and nitrogen adsorption/desorption isotherms. The results indicated that hydroxy-aluminum ([Al13O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe cations were intercalated into layers of clay, resulting in an increase of d001 values and of the specific surface areas compared with those of initial bentonite. Modified bentonites were employed to adsorb As(V) from aqueous solution. The adsorption of As(V) was strongly dependent on solution pH, and the maximum adsorption of modified bentonites was obtained in the pH 3.0 for Fe-bentonite and the pH 4.0 for Al-bentonite. The equilibrium adsorption study showed that the data were well fit by the Langmuir isotherm model. The maximum monolayer adsorption capacity of As(V) at 30°C derived from the Langmuir equation was 35.71 mg/g for Al-bentonite and 18.98 mg/g for Fe-bentonite. Adsorption kinetics, thermodynamics, and reusability of modified bentonites have been addressed.

Structural and surface aspects of thermally treated copper aluminium mixed hydroxides

1991 ◽  
Vol 69 (10) ◽  
pp. 1511-1515 ◽  
Author(s):  
Awad I. Ahmed ◽  
S. E. Samra ◽  
S. A. El-Hakam
Keyword(s):  
Pore Structure ◽  
Copper Content ◽  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Areas ◽  
Structure Surface ◽  
Adsorption Desorption

CuO–Al2O3 catalysts containing various amounts of copper oxide have been prepared by precipitation. The phase changes were studied by X-ray diffraction. The results obtained revealed that the thermal treatment of solid CuO–Al2O3 at 700 °C produced only crystalline CuO. Heating to 900 °C led to the formation of copper alumina spinel together with unreacted CuO and γ-Al2O3. The spinel content was found to increase with increasing copper content. Nitrogen adsorption–desorption isotherms on the calcined samples have been measured. Surface areas have been calculated and the pore structure analysed. The textural properties of the system were found to depend on both the copper content and the calcination temperature. Key words: CuO, Al2O3 catalysts, structure, surface area, pore structure.

Study of the catalytic activity of Al-Fe pillared clays in the Baeyer–Villiger oxidation

Clay Minerals ◽  
2012 ◽  
Vol 47 (2) ◽  
pp. 275-284 ◽  
Author(s):  
L. S. Belaroui ◽  
A. Bengueddach
Keyword(s):  
Textural Properties ◽  
Nitrogen Adsorption ◽  
Pillared Clays ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dissolved Iron ◽  
Surface Areas ◽  
Accessible Surface ◽  
Adsorption Desorption ◽  
Villiger Oxidation

AbstractThree types of AlFePILCs pillared clays have been prepared from Algerian clay precursors. They have been characterized and tested in the Baeyer–Villiger oxidation of cyclohexanone to caprolactone using benzaldehyde and oxygen as oxidant at room temperature. The structural and textural properties of the catalyst have been determined by X-ray diffraction, nitrogen adsorption-desorption isotherms and Mössbauer spectroscopy.The different activities of the clays have been related to their Fe contents and accessible surface areas. The induction period observed before the reaction started has been attributed to the dissolution of a portion of the Fe3+ cations, mediated by either the perbenzoic acid intermediate or the benzoic acid co-product. The reaction was indeed catalysed by a few ppm of dissolved iron cations and the catalysis of the Baeyer–Villiger oxidation reaction should mechanistically be considered as homogeneous.

scholarly journals Synthesis and Characterization of CuFe2O4 Nanoparticles Modified with Polythiophene: Applications to Mercuric Ions Removal

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 586 ◽  
Author(s):  
Ayman H. Kamel ◽  
Amr A. Hassan ◽  
Abd El-Galil E. Amr ◽  
Hadeel H. El-Shalakany ◽  
Mohamed A. Al-Omar
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Transmission Electron ◽  
Enhanced Adsorption ◽  
Co Precipitation ◽  
Adsorption Desorption

In this research, CuFe2O4 nanoparticles were synthesized by co-precipitation methods and modified by coating with thiophene for removal of Hg(II) ions from aqueous solution. CuFe2O4 nanoparticles, with and without thiophene, were characterized by x-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), energy dispersive x-ray (EDX), high-resolution transmission electron microscopy (HRTEM) and Brunauer–Emmett–Teller (BET). Contact time, adsorbent dose, solution pH, adsorption kinetics, adsorption isotherm and recyclability were studied. The maximum adsorption capacity towards Hg2+ ions was 7.53 and 208.77 mg/g for CuFe2O4 and CuFe2O4@Polythiophene composite, respectively. Modification of CuFe2O4 nanoparticles with thiophene revealed an enhanced adsorption towards Hg2+ removal more than CuFe2O4 nanoparticles. The promising adsorption performance of Hg2+ ions by CuFe2O4@Polythiophene composite generates from soft acid–soft base strong interaction between sulfur group of thiophene and Hg(II) ions. Furthermore, CuFe2O4@Polythiophene composite has both high stability and reusability due to its removal efficiency, has no significant decrease after five adsorption–desorption cycles and can be easily removed from aqueous solution by external magnetic field after adsorption experiments took place. Therefore, CuFe2O4@Polythiophene composite is applicable for removal Hg(II) ions from aqueous solution and may be suitable for removal other heavy metals.

scholarly journals Removal of rhodamine B from aqueous solution by adsorption on corn cobs activated carbon

2021 ◽  
Vol 11 (3) ◽  
pp. 271
Author(s):  
Kambiré Ollo ◽  
Kouakou Yao Urbain ◽  
Kouyaté Amadou ◽  
Sadia Sahi Placide ◽  
Kouadio Kouakou Etienne ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Rhodamine B ◽  
X Ray Diffraction ◽  
Titration Method ◽  
X Ray ◽  
Corn Cobs ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

<p>In the present study, adsorption experiments were carried out to investigate the removal of rhodamine B from an aqueous solution using chemically activated carbon from corn cobs, a cheaper adsorbent. The characteristics of carbon were determined using X-ray diffraction, SEM, iodine number, pHpzc, and the Boehm titration method. The results show that the prepared activated carbon is amorphous, microporous, and generally acidic on the surface. The kinetic study of the adsorption of rhodamine B on this carbon was carried out, and the rate of sorption was found to conform to pseudo-second-order kinetics with 80 min as equilibrium time. The equilibrium adsorption revealed that the experimental data fitted better to the Langmuir isotherm model for removing rhodamine B. The interaction rhodamine B-activated carbon is mainly chemisorption type. The optimal conditions of rhodamine B removal onto the carbon of this study are mass of carbon = 0.3 g and pH = 3.15. The maximum monolayer adsorption capacity for rhodamine B removal was found to be 5.92 mg.g<sup>-1</sup>. This study has shown that the prepared activated carbon makes it possible to effectively clean up wastewater contaminated by rhodamine B with a removal efficiency of up to 99.60% for 300 mg of AC in 25 mL of the rhodamine B solution (5 mg.L<sup>-1</sup>).</p>

Application of raw and modified Uruguayan clays to phosphate adsorption for water remediation

MRS Advances ◽  
2018 ◽  
Vol 3 (61) ◽  
pp. 3543-3549
Author(s):  
Pablo González ◽  
Andrea C. De Los Santos ◽  
Jorge R. Castiglioni ◽  
María A. De León
Keyword(s):  
Nitrogen Adsorption ◽  
Pillared Clay ◽  
Water Remediation ◽  
Phosphate Adsorption ◽  
X Ray Diffraction ◽  
Order Model ◽  
Freundlich Model ◽  
X Ray ◽  
First Order ◽  
Adsorption Desorption

ABSTRACTA raw clay from Uruguay was modified with aluminium to obtain an aluminium pillared clay (Al-PILC). The solids were characterized by scanning electron microscopy, X-ray diffraction and nitrogen adsorption-desorption isotherms. The Al-PILC retained the typical laminar structure of montmorillonite. The specific surface area and the microporous volume of the Al-PILC, 235 m2 g-1 and 0.096 cm3 g-1, respectively, were much higher than those of the clay. The phosphate adsorption capacity of the Al-PILC was higher than those of the clay. The phosphate adsorption kinetic followed the pseudo-first-order model for both, the clay and the Al-PILC, and the phosphate adsorption isotherm for the Al-PILC fit the Freundlich model.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

scholarly journals Effect of the Organobentonite Filler on Structure and Properties of Composites Based on Hydroxyethyl Cellulose

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Olga V. Alekseeva ◽  
Anna N. Rodionova ◽  
Nadezhda A. Bagrovskaya ◽  
Alexander V. Agafonov ◽  
Andrew V. Noskov
Keyword(s):  
Tensile Properties ◽  
Composite Films ◽  
Nitrogen Adsorption ◽  
Hydroxyethyl Cellulose ◽  
X Ray Diffraction ◽  
Ir Spectrometry ◽  
X Ray ◽  
Mechanical Dispersion ◽  
Filling Agent ◽  
Adsorption Desorption

Organobentonite powder was synthesized and characterized using laser diffraction, X-ray diffraction, low-temperature nitrogen adsorption-desorption technique, and dynamic light scattering. Obtained powder was found as material with mesopores. The organobentonite particles were larger than pure bentonite one. Hydroxyethyl cellulose (HEC) was filled with organobentonite particles by mechanical dispersion, and produced composite films were researched by the number of methods. New data relating to structure, tensile properties, and antimicrobial activity of HEC/organobentonite composites were obtained. Using results of X-ray diffraction, the reflections assigned to crystal filler in polymer material were proved. Concentration effect of the filling agent on tensile properties of composite film was revealed. Data of infrared (IR) spectrometry indicated a decrease in the density of hydrogen-bond net in HEC/organobentonite composite as compared with pristine HEC. Using microbiological tests, it was found that the HEC/organobentonite films exhibited bacteriostatic action against S. aureus and fungistatic action against molds.

Investigation of ZnO/CuO/Nanographene Platelets Composites Catalyst for the Degradation of Methylene Blue from Aqueous Solution

2016 ◽  
Vol 864 ◽  
pp. 117-122 ◽  
Author(s):  
Hesni Shabrany ◽  
Hendry Tju ◽  
Ardiansyah Taufik ◽  
Rosari Saleh
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Catalytic Activity ◽  
Visible Light ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
Ultrasound Irradiation ◽  
X Ray Diffraction ◽  
X Ray

This paper discusses the catalytic activity of ZnO/CuO/nanographene platelets composites under visible light and ultrasound irradiation separately. The ZnO/CuO/nanographene platelets composites were synthesized using a sol-gel method. X-ray diffraction and nitrogen adsorption spectroscopy were employed to investigate the structural and surface area of the catalyst. The catalytic activity results showed that the presence of nanographene platelets in ZnO/CuO nanocomposites improved its efficiency in degrading methylene blue. A scavenger method was also used to understand the role of charged carriers and the active radical involved in the catalytic activity.

Positron Annihilation Study of Porous ZnO Synthesized with Soft Template

2017 ◽  
Vol 373 ◽  
pp. 299-302
Author(s):  
Bo Zhou ◽  
Chong Yang Li ◽  
Ning Qi ◽  
Zhi Quan Chen
Keyword(s):  
Pore Size ◽  
Positron Lifetime ◽  
Nitrogen Adsorption ◽  
Soft Template ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Long Lifetime ◽  
Positron Annihilation Study ◽  
Adsorption Desorption

Porous ZnO were synthesized with soft template method using zinc acetate Zn (CH3COO)2·2H2O as precursor and block copolymer F127 as the surfactant. Nitrogen adsorption-desorption measurements indicate that the ZnO sample contains large pores with mean diameter of about 30 nm. However, both small-angle X-ray diffraction and transmission electron microscope measurements indicate that the pore ordering is missing. Positron lifetime measurements reveal two long lifetime components in the porous ZnO. The longest lifetime τ4 (75 ns) corresponds to ortho-positronium (o-Ps) annihilation in large pores. The pore size estimated from τ4 is about 10.6 nm. This is much smaller than that estimated from Nitrogen adsorption-desorption measurements. In addition, the intensity I4 is only about 2.2%. This is probably due to the chemical quenching and/or inhibition of positronium formation induced by ZnO, which reduces o-Ps lifetime and intensity, and leads to under estimation of the pore size.

Catalytic Activity of Argentum-loaded MCM-41 for Ozonation of p- Chlorobenzoic Acid (p-CBA) in Aqueous Solution

2015 ◽  
Vol 18 (1) ◽  
Author(s):  
Zhaoqi Pan ◽  
Junyu Zeng ◽  
Bingyan Lan ◽  
Laisheng Li
Keyword(s):  
Aqueous Solution ◽  
Nitrogen Adsorption ◽  
Hexagonal Structure ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
Chlorobenzoic Acid ◽  
Transmission Electron ◽  
Initial Ph ◽  
Adsorption Desorption ◽  
Mcm 41

AbstractArgentum-loaded MCM-41 (Ag/MCM-41) was synthesized successfully by a hydrothermal method and used as a catalyst for the ozonation of p-chlorobenzoic acid (p-CBA) in aqueous solution. Ag/MCM-41 was characterized by low angle X-ray diffraction (XRD), nitrogen adsorption-desorption and transmission electron microscopy (TEM). Characterizations suggest that the prepared samples retained a highly regulated mesopores of hexagonal structure and a high BET surface area. The influences of argentum content, initial pH, reaction temperature on the catalytic ozonation were also evaluated. Ag/MCM-41/O

Sign in / Sign up

Export Citation Format

Share Document