scholarly journals Development Research on Integrating CNC Machine Tool with Plasma for Online Surface Heat Treatment

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Shao-Hsien Chen ◽  
Bo-Ting Wang
Keyword(s):  
Heat Treatment ◽  
Real Time ◽  
Feed Rate ◽  
Surface Hardness ◽  
Spindle Speed ◽  
Experimental Results ◽  
Machining Process ◽  
Cnc Machine ◽  
Optimum Parameters ◽  
Hardening Effect

In this study, the plasma was integrated with a lathe, and the online heat treatment was performed to achieve mechanical strength and hardness, to reduce the machining process and handling. However, for online heat treatment of cast iron FC25, it is important to study the parameters of the lathe and plasma, and the research method is used eventually to optimize the process and reduce the machining cost and machining error. The variable factors in the surface online real-time heat treatment are spindle speed, feed rate, and current, and the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using a full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for the optimization experiment, and the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include spindle speed, feed rate, and current and the optimum parameters include spindle speed of 168 rpm, feed rate of 0.068 mm/rev, and current of 86 A. The experimental results of optimum parameters show that the surface hardness is increased from 306 HLD to 806 HLD and the surface hardening effect is enhanced by 163%, so the online real-time heat treatment equipment has the best hardening effect.

scholarly journals Development Research on Integrating CNC Machine Tool with Plasma for On-line Surface Heat Treatment

2021 ◽  
Author(s):  
Shao Hsien Chen ◽  
Bo-Ting Wang
Keyword(s):  
Heat Treatment ◽  
Mechanical Strength ◽  
Real Time ◽  
Feed Rate ◽  
Surface Hardness ◽  
Experimental Results ◽  
Machining Process ◽  
Optimum Parameters ◽  
Hardening Effect ◽  
On Line

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Characterizing the Effect of Cutting Condition, Tool Path, and Heat Treatment on Cutting Forces of Selective Laser Melting Spherical Component in Five-Axis Milling

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Amir Mahyar Khorasani ◽  
Ian Gibson ◽  
Moshe Goldberg ◽  
Guy Littlefair
Keyword(s):  
Heat Treatment ◽  
Production Process ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
Tool Path ◽  
Annealing Temperature ◽  
Spindle Speed ◽  
Cutting Condition ◽  
Scallop Height

Additive manufacturing (AM), partly due to its compatibility with computer-aided design (CAD) and fabrication of intricate shapes, is an emerging production process. Postprocessing, such as machining, is particularly necessary for metal AM due to the lack of surface quality for as-built parts being a problem when using as a production process. In this paper, a predictive model for cutting forces has been developed by using artificial neural networks (ANNs). The effect of tool path and cutting condition, including cutting speed, feed rate, machining allowance, and scallop height, on the generated force during machining of spherical components such as prosthetic acetabular shell was investigated. Also, different annealing processes like stress relieving, mill annealing and β annealing have been carried out on the samples to better understand the effect of brittleness, strength, and hardness on machining. The results of this study showed that ANN can accurately apply to model cutting force when using ball nose cutters. Scallop height has the highest impact on cutting forces followed by spindle speed, finishing allowance, heat treatment/annealing temperature, tool path, and feed rate. The results illustrate that using linear tool path and increasing annealing temperature can result in lower cutting force. Higher cutting force was observed with greater scallop height and feed rate while for higher finishing allowance, cutting forces decreased. For spindle speed, the trend of cutting force was increasing up to a critical point and then decreasing due to thermal softening.

Development of a Smart Computer Numerical Control System

2013 ◽  
Author(s):  
Zhiqian Sang ◽  
Xun Xu
Keyword(s):  
Real Time ◽  
High Speed ◽  
Computer Numerical Control ◽  
Numerical Control ◽  
Machining Process ◽  
Cnc Machine ◽  
Field Bus ◽  
Nc System ◽  
Tool Paths ◽  
Cnc Controller

Traditional Computer Numerical Control (CNC) machines use ISO6983 (G/M code) for part programming. G/M code has a number of drawbacks and one of them is lack of interoperability. The Standard for the Exchange of Product for NC (STEP-NC) as a potential replacement for G/M code aims to provide a unified and interoperable data model for CNC. In a modern CNC machine tool, more and more motors, actuators and sensors are implemented and connected to the NC system, which leads to large quantity of data being transmitted. The real-time Ethernet field-bus is faster and more deterministic and can fulfill the requirement of data transmission in the high-speed and high-precision machining scenarios. It can provide more determinism on communication, openness, interoperability and reliability than a traditional field-bus. With a traditional CNC system using G/M code, when the machining is interrupted by incidents, restarting the machining process is time-consuming and highly experience-dependent. The proposed CNC controller can generate just-in-time tool paths for feature-based machining from a STEP-NC file. When machining stoppage occurs, the system can recover from stoppage incidents with minimum human intervention. This is done by generating new tool paths for the remaining machining process with or without the availability of the original cutting tool. The system uses a real-time Ethernet field-bus as the connection between the controller and the motors.

scholarly journals EFFECT OF MINIMUM QUANTITY LUBRICATION ON SURFACE ROUGHNESS IN TOOL-BASED MICROMILLING

2017 ◽  
Vol 18 (1) ◽  
pp. 147-154
Author(s):  
Mohammad Yeakub Ali ◽  
Wan Norsyazila Jailani ◽  
Mohamed Rahman ◽  
Muhammad Hasibul Hasan ◽  
Asfana Banu
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Spindle Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Microfluidic Channels ◽  
Machining Parameters ◽  
Machining Processes ◽  
Dry Cutting ◽  
Minimum Quantity

Cutting fluid plays an important role in machining processes to achieve dimensional accuracy in reducing tool wear and improving the tool life. Conventional flood cooling method in machining processes is not cost effective and consumption of huge amount of cutting fluids is not healthy and environmental friendly. In micromachining, flood cooling is not recommended to avoid possible damage of the microstructures. Therefore, one of the alternatives to overcome the environmental issues to use minimum quantity of lubrication (MQL) in machining process. MQL is eco-friendly and has economical advantage on manufacturing cost. However, there observed lack of study on MQL in improving machined surface roughness in micromilling. Study of the effects of MQL on surface roughness should be carried out because surface roughness is one of the important issues in micromachined parts such as microfluidic channels. This paper investigates and compares surface roughness with the presence of MQL and dry cutting in micromilling of aluminium alloy 1100 using DT-110 milling machine. The relationship among depth of cut, feed rate, and spindle speed on surface roughness is also analyzed. All three machining parameters identified as significant for surface roughness with dry cutting which are depth of cut, feed rate, and spindle speed. For surface roughness with MQL, it is found that spindle speed did not give much influence on surface roughness. The presence of MQL provides a better surface roughness by decreasing the friction between tool and workpiece.

scholarly journals Surface roughness of thermally treated wood cut with different parameters in CNC router machine

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5133-5147
Author(s):  
Hüseyin Pelit ◽  
Mustafa Korkmaz ◽  
Mehmet Budakçı
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Treatment Temperature ◽  
Spindle Speed ◽  
Numerical Control ◽  
Machining Parameters ◽  
End Mill ◽  
Cnc Machine ◽  
Cnc Router ◽  
Thermally Treated

The effects of different machining parameters on surface roughness values of thermally treated pine, beech, and linden woods cut in a computer numerical control (CNC) router machine were examined. Wood specimens were thermally treated at 170, 190, and 210 °C for 2 h. Then, specimens were cut in the radial and tangential directions with three different spindle speeds (12000, 15000, and 18000 rpm) and three different feed rates (3000, 4000, and 6000 mm/min) using two different end mill tools (spiral and straight) on the CNC machine. The end mill type significantly affected the roughness values of the untreated and thermally treated specimens in both directions. Lower roughness values were found in the specimens (especially pine) machined with the straight end mill compared to those machined with the spiral end mill. Roughness generally decreased in the thermally treated specimens. However, thermal treatment temperature did not have a notable effect on roughness. As the spindle speed increased, the roughness values of all specimens decreased. In contrast, as the feed rate increased, the roughness values increased. Therefore, the end mill type, feed rate, and spindle speed were the most influential parameters on the roughness.

scholarly journals Effects of Turning Parameters and Parametric Optimization of the Cutting Forces in Machining SiCp/Al 45 wt% Composite

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 840 ◽  
Author(s):  
Rashid Ali Laghari ◽  
Jianguang Li ◽  
Mozammel Mia
Keyword(s):  
Mathematical Model ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
Desirability Function ◽  
Interactive Effect ◽  
Cutting Speed ◽  
Experimental Results ◽  
Machining Process ◽  
Depth Of Cut

Cutting force in the machining process of SiCp/Al particle reinforced metal matrix composite is affected by several factors. Obtaining an effective mathematical model for the cutting force is challenging. In that respect, the second-order model of cutting force has been established by response surface methodology (RSM) in this study, with different cutting parameters, such as cutting speed, feed rate, and depth of cut. The optimized mathematical model has been developed to analyze the effect of actual processing conditions on the generation of cutting force for the turning process of SiCp/Al composite. The results show that the predicted parameters by the RSM are in close agreement with experimental results with minimal error percentage. Quantitative evaluation by using analysis of variance (ANOVA), main effects plot, interactive effect, residual analysis, and optimization of cutting forces using the desirability function was performed. It has been found that the higher depth of cut, followed by feed rate, increases the cutting force. Higher cutting speed shows a positive response by reducing the cutting force. The predicted and experimental results for the model of SiCp/Al components have been compared to the cutting force of SiCp/Al 45 wt%—the error has been found low showing a good agreement.

Development of Computer-Aided Manufacturing System for a Jewelry-Making CNC Machine

2014 ◽  
Vol 596 ◽  
pp. 83-89 ◽  
Author(s):  
Ya Miao ◽  
Kai He ◽  
Hai Tao Fang ◽  
Zhi Min Zhou ◽  
Ru Xu Du
Keyword(s):  
Manufacturing System ◽  
Experimental Results ◽  
Machining Process ◽  
Computer Interface ◽  
Machining Parameters ◽  
Basic Design ◽  
Human Computer Interface ◽  
Cnc Machine ◽  
Gold Bead ◽  
Computer Aided

Abstract. This paper designs a CAM system for a jewelry-making CNC machine. The CAM system not only provides a human-computer interface for setting machining parameters, but also can generate special NC programs automatically and realize the simulation for the machining process. In addition, the paper gives an efficient application for machining an ellipsoidal gold bead. The basic design of the jewelry-making CAM system and the experimental results are presented.

The Process Study on Laser Heat Treatment for CNC Machine Tool Guide

2010 ◽  
Vol 42 ◽  
pp. 335-338
Author(s):  
Hua Li Su ◽  
Xiao Peng Miao ◽  
Yong Zhang
Keyword(s):  
Heat Treatment ◽  
Machine Tool ◽  
Surface Hardness ◽  
High Hardness ◽  
Hardened Layer ◽  
Numerical Control ◽  
Cnc Machine Tools ◽  
Cnc Machine Tool ◽  
Cnc Machine ◽  
Control Machine Tool

With the continuous development of CNC technology, CNC machine tools run at the higher speed. Cutting force will be greater, which is bound to exacerbate the wear and tear of the machine tool guides. Therefore, new requirements of numerical control machine tool guide surface hardness are proposed. Using Laser surface heat treatment process to scan the guide surface of CNC Machine Tool, the guide can get high hardness hardened layer. After being casted iron HT300 was heat treated by the laser, the microstructure is homogeneous, very fine martensite. Its Surface hardness can get to HV832. The treatment enhances the surface abrasion resistance, scratch-resistant capacity.

Virtual Simulation and Remote Desktop Interface for CNC Milling Operation

2011 ◽  
Vol 264-265 ◽  
pp. 1643-1647 ◽  
Author(s):  
Afzeri ◽  
Agus Geter E. Sutjipto ◽  
R. Muhida ◽  
Mohamed Konneh ◽  
Darmawan
Keyword(s):  
Real Time ◽  
Computer Network ◽  
Milling Process ◽  
Virtual Simulation ◽  
Machining Process ◽  
Milling Machine ◽  
Cnc Milling ◽  
Cnc Machine ◽  
Remote Operation ◽  
Workpiece Setup

Advanced development of computer network through Internet brings the technology to Manufacturing. Increasing the demand for effectively use of the production facility requires the tools for sharing the manufacturing facility by remote operation of the machining process. This paper introduces the methodology of machining technology for direct remote operation of networked milling machine. The tools including virtual simulation using CAD model, remote desktop protocol and Setup Free Attachment for remote operation of milling process are proposed. Accessing and monitoring of machining operation is performed by remote desktop interface and 3D virtual simulations. Capability of remote operation is supported by an auto setup attachment with a reconfigurable pin type setup free technology installed on the table of CNC milling machine to perform unattended machining process. The system is designed using a computer server and connected to a PC based controlled CNC machine for real time monitoring. A client will access the server through internet communication and virtually simulate the machine activity. The result has been presented that combination between real time virtual simulation and remote desktop tool is enabling to operate all machine tool functions and as well as workpiece setup.

Sign in / Sign up

Export Citation Format

Share Document