3D X-Ray Inspection of a Radio Controlled Airplane Engine

2015 ◽  
Vol 828-829 ◽  
pp. 433-438 ◽  
Author(s):  
Anton du Plessis ◽  
Stephan Gerhard le Roux ◽  
Herman van Rooyen
Keyword(s):  
Light Metal ◽  
Light Metals ◽  
Casting Defects ◽  
Micro Computed Tomography ◽  
X Ray ◽  
Metal Parts ◽  
Airplane Engine ◽  
Dimensional Measurements ◽  
Microct Analysis

This paper describes a typical 3D X-ray micro computed tomography (microCT) analysis of light metal parts, from a radio controlled airplane engine. This case study shows the power of 3D X-ray inspection and analysis for this type of material, including information about the size and location of casting defects, the location of turbine blade balancing weights and dimensional measurements indicating the axle was not perfectly centre. Advantages and limitations of the method for light metals are described in general

scholarly journals A Review of Current Challenges and Case Study toward Optimizing Micro-Computed X-Ray Tomography of Carbon Fabric Composites

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3606
Author(s):  
Armin Rashidi ◽  
Tina Olfatbakhsh ◽  
Bryn Crawford ◽  
Abbas S. Milani
Keyword(s):  
Computed Tomography ◽  
Woven Fabric ◽  
Fiber Reinforced Polymers ◽  
Micro Ct ◽  
Micro Computed Tomography ◽  
X Ray ◽  
Fabric Composites ◽  
Low X ◽  
Composite Fabrics

X-ray computed tomography provides qualitative and quantitative structural and compositional information for a broad range of materials. Yet, its contribution to the field of advanced composites such as carbon fiber reinforced polymers is still limited by factors such as low imaging contrast, due to scarce X-ray attenuation features. This article, through a review of the state of the art, followed by an example case study on Micro-computed tomography (CT) analysis of low X-ray absorptive dry and prepreg carbon woven fabric composites, aims to highlight and address some challenges as well as best practices on performing scans that can capture key features of the material. In the case study, utilizing an Xradia Micro-CT-400, important aspects such as obtaining sufficient contrast, an examination of thin samples, sample size/resolution issues, and image-based modeling are discussed. The outcome of an optimized workflow in Micro-CT of composite fabrics can assist in further research efforts such as the generation of surface or volume meshes for the numerical modeling of underlying deformation mechanisms during their manufacturing processes.

scholarly journals 3D revelation of phenotypic variation, evolutionary allometry, and ancestral states of corolla shape: a case study of clade Corytholoma (subtribe Ligeriinae, family Gesneriaceae)

GigaScience ◽  
2020 ◽  
Vol 9 (1) ◽  
Author(s):  
Hao-Chun Hsu ◽  
Wen-Chieh Chou ◽  
Yan-Fu Kuo
Keyword(s):  
Morphological Traits ◽  
Spatial Information ◽  
Shape Variation ◽  
Micro Computed Tomography ◽  
3D Images ◽  
X Ray ◽  
Evolutionary Allometry ◽  
Ancestral States ◽  
3D Landmarks

Abstract Background Quantification of corolla shape variations helps biologists to investigate plant diversity and evolution. 3D images capture the genuine structure and provide comprehensive spatial information. Results This study applied X-ray micro-computed tomography (µCT) to acquire 3D structures of the corollas of clade Corytholoma and extracted a set of 415 3D landmarks from each specimen. By applying the geometric morphometrics (GM) to the landmarks, the first 4 principal components (PCs) in the 3D shape and 3D form analyses, respectively, accounted for 87.86% and 96.34% of the total variance. The centroid sizes of the corollas only accounted for 5.46% of the corolla shape variation, suggesting that the evolutionary allometry was weak. The 4 morphological traits corresponding to the 4 shape PCs were defined as tube curvature, lobe area, tube dilation, and lobe recurvation. Tube curvature and tube dilation were strongly associated with the pollination type and contained phylogenetic signals in clade Corytholoma. The landmarks were further used to reconstruct corolla shapes at the ancestral states. Conclusions With the integration of µCT imaging into GM, the proposed approach boosted the precision in quantifying corolla traits and improved the understanding of the morphological traits corresponding to the pollination type, impact of size on shape variation, and evolution of corolla shape in clade Corytholoma.

X-ray micro-computed tomography of burrow-related porosity and permeability in shallow-marine equatorial carbonates: A case study from the Miocene Pirabas Formation, Brazil

2021 ◽  
pp. 104966
Author(s):  
Olga M. Oliveira de Araújo ◽  
Orangel Aguilera ◽  
Giovanni Coletti ◽  
Fernando L. Valencia ◽  
Luis A. Buatois ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Micro Computed Tomography ◽  
Shallow Marine ◽  
X Ray ◽  
Porosity And Permeability

Morphology and Affinities of Ampelocissites Seeds (Vitaceae: Ampelopsis clade) from the Paleogene of Texas, USA

2020 ◽  
Vol 45 (3) ◽  
pp. 478-482
Author(s):  
Steven R. Manchester
Keyword(s):  
Computed Tomography ◽  
Cross Sections ◽  
Seed Coat ◽  
Ct Scanning ◽  
Seed Morphology ◽  
Early Eocene ◽  
Micro Computed Tomography ◽  
X Ray ◽  
Fossil Seeds ◽  
Fossil Genus

Abstract—The type material on which the fossil genus name Ampelocissites was established in 1929 has been reexamined with the aid of X-ray micro-computed tomography (μ-CT) scanning and compared with seeds of extant taxa to assess the relationships of these fossils within the grape family, Vitaceae. The specimens were collected from a sandstone of late Paleocene or early Eocene age. Although originally inferred by Berry to be intermediate in morphology between Ampelocissus and Vitis, the newly revealed details of seed morphology indicate that these seeds represent instead the Ampelopsis clade. Digital cross sections show that the seed coat maintains its thickness over the external surfaces, but diminishes quickly in the ventral infolds. This feature, along with the elliptical chalaza and lack of an apical groove, indicate that Ampelocissites lytlensis Berry probably represents Ampelopsis or Nekemias (rather than Ampelocissus or Vitis) and that the generic name Ampelocissites may be useful for fossil seeds with morphology consistent with the Ampelopsis clade that lack sufficient characters to specify placement within one of these extant genera.

INVESTIGATION OF AUBRITES THROUGH INTEGRATION OF 3D MODAL MINERALOGY WITH X-RAY MICRO-COMPUTED TOMOGRAPHY AND GEOCHEMISTRY

2018 ◽  
Author(s):  
Zoë E. Wilbur ◽  
◽  
Arya Udry ◽  
Arya Udry ◽  
Daniel M. Coleff ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Micro Computed Tomography ◽  
X Ray

scholarly journals Characterization and mapping of hematite ore mineral classes using hyperspectral remote sensing technique: a case study from Bailadila iron ore mining region

2021 ◽  
Vol 3 (2) ◽  
Author(s):  
Ibrahim Shaik ◽  
S. K. Begum ◽  
P. V. Nagamani ◽  
Narayan Kayet
Keyword(s):  
Infrared Absorption ◽  
Near Infrared ◽  
Spectral Feature ◽  
Absorption Feature ◽  
X Ray ◽  
Remote Sensing Technique ◽  
Ore Minerals ◽  
Feature Fitting ◽  
Hematite Ore

AbstractThe study demonstrates a methodology for mapping various hematite ore classes based on their reflectance and absorption spectra, using Hyperion satellite imagery. Substantial validation is carried out, using the spectral feature fitting technique, with the field spectra measured over the Bailadila hill range in Chhattisgarh State in India. The results of the study showed a good correlation between the concentration of iron oxide with the depth of the near-infrared absorption feature (R2 = 0.843) and the width of the near-infrared absorption feature (R2 = 0.812) through different empirical models, with a root-mean-square error (RMSE) between < 0.317 and < 0.409. The overall accuracy of the study is 88.2% with a Kappa coefficient value of 0.81. Geochemical analysis and X-ray fluorescence (XRF) of field ore samples are performed to ensure different classes of hematite ore minerals. Results showed a high content of Fe > 60 wt% in most of the hematite ore samples, except banded hematite quartzite (BHQ) (< 47 wt%).

scholarly journals Investigation of opening eye defects and effects of different ripening profiles on eye structure in semi-hard cheese using X-ray micro-computed tomography

2021 ◽  
Vol 28 ◽  
pp. 100190
Author(s):  
Jaqueline Auer ◽  
Michael Reiter ◽  
Sascha Senck ◽  
Andreas Reiter ◽  
Johann Kastner ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Micro Computed Tomography ◽  
X Ray ◽  
Hard Cheese
Sign in / Sign up

Export Citation Format

Share Document