Design of a Hand-Held and Battery-Operated Digital Microfluidics Device Using EWOD for Lab-on-a-Chip Applications

Microfluidics offer many advantages to Point of Care (POC) devices through lower reagent use and smaller size. Additionally, POC devices offer the unique potential to conduct tests outside of the laboratory. In particular, Electro-wetting on Dielectric (EWOD) microfluidics has been shown to be an effective way to move and mix liquids enabling many PoC devices. However, much of the research surrounding these microfluidic systems are focused on a single aspect of the system capability, such as droplet control or a specific new application at the device level using the EWOD technology. Often in these experiments the supporting systems required for operation are bench top equipment such as function generators, power supplies, and personal computers. Although various aspects of how an EWOD device is capable of moving and mixing droplets have been demonstrated at various levels, a complete self-contained and portable lab-on-a-chip system based on the EWOD technology has not been well demonstrated. For instance, EWOD systems tend to use high voltage alternating current (AC) signals to actuate electrodes, but little consideration is given to circuitry size or power consumption of such components to make the entire system portable. This paper demonstrates the feasibility of integrating all supporting hardware and software to correctly operate an EWOD device in a completely self-contained and battery-powered handheld unit. We present results that demonstrate a complete sample preparation flow for deoxyribonucleic acid (DNA) extraction and isolation. The device was designed to be a field deployable, hand-held platform capable of performing many other sample preparation tasks automatically. Liquids are transported using EWOD and controlled via a programmable microprocessor. The programmable nature of the device allows it to be configured for a variety of tests for different applications. Many considerations were given towards power consumption, size, and system complexity which make it ideal for use in a mobile environment. The results presented in this paper show a promising step forward to the portable capability of microfluidic devices based on the EWOD technology.

Field Emission Air-Channel Devices as a Voltage Adder

Field emission air-channel (FEAC) devices can work under atmospheric pressure with a low operation voltage when the electron channel is far less than the mean free path (MFP) in the air, thereby making them a practical component in circuits. Forward and reverse electron emissions of the current FEAC devices demonstrated symmetric Fowler–Nordheim (F–N) plots owing to the symmetric cathode and anode electrodes. This research aimed to demonstrate the arithmetic application of the FEAC devices, their substrate effect, and reliability. A voltage adder was composed of two FEAC devices whose two inputs were connected to two separate function generators, and one output was wire-connected to an oscilloscope. The devices were on a thin dielectric film and low-resistivity silicon substrate to evaluate the parasitic components and substrate effect, resulting in frequency-dependent impedance. The results show that the FEAC devices possessed arithmetic function, but the output voltage decreased. The FEAC devices were still capable of serving as a voltage adder after the reliability test, but electric current leakage increased. Finite element analysis indicated that the highest electrical fields and electron trajectories occur at the apices where the electrons travel with the shortest route less than the MFP in the air, thereby meeting the FEAC devices’ design. The modeling also showed that a sharp apex would generate a high electric field at the tip-gap-tip, enhancing the tunneling current.

Controlling the Movement of a TRR Spatial Chain With Coupled Six-Bar Function Generators for Biomimetic Motion

This paper describes a synthesis technique that constrains a spatial serial chain into a single degree-of-freedom mechanism using planar six-bar function generators. The synthesis process begins by specifying the target motion of a serial chain that is parameterized by time. The goal is to create a mechanism with a constant velocity rotary input that will achieve that motion. To do this, we solve the inverse kinematics equations to find functions of each serial joint angle with respect to time. Since a constant velocity input is desired, time is proportional to the angle of the input link, and each serial joint angle can be expressed as functions of the input angle. This poses a separate function generator problem to control each joint of the serial chain. Function generators are linkages that coordinate their input and output angles. Each function is synthesized using a technique that finds 11 position Stephenson II linkages, which are then packaged onto the serial chain. Using pulleys and the scaling capabilities of function generating linkages, the final device can be packaged compactly. We describe this synthesis procedure through the design of a biomimetic device for reproducing a flapping wing motion.