automatic wire
Recently Published Documents


TOTAL DOCUMENTS

40
(FIVE YEARS 7)

H-INDEX

4
(FIVE YEARS 1)

Micromachines ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 24
Author(s):  
Jun Cao ◽  
Junchao Zhang ◽  
Kexing Song ◽  
Baoan Wu ◽  
Yong Ding ◽  
...  

The effects of the geometry parameters of a ceramic cleaver on the morphology of ball and second bonded points were studied using an automatic wire bonder, push pull tester, scanning electron microscope, ceramic capillary with different geometric parameters and φ25.4 μmAg-5Au bonding alloy wire, etc. The result shows that when the inner hole diameter (IHD) of the ceramic capillary is 1.3 times the diameter of the alloy wire (33 μm), the neck morphology of the ball bonded point (first bonded point) meet the requirements. The neck of the ball bonded point appeared to fracture when the IHD is 26 μm; The neck of the ball bonded point appeared as an irregular shape when the IHD is 41 μm. When the inner cutting angle diameter (ICAD) is 64 μm, the size of the mashed ball diameter (MBD) is qualified. When the ICAD is 51 μm, the MBD is too large and mashed ball overflows the pad. When the ICAD is 76 μm, the ball bonded point is too high. When the inner cutting bevel angle (ICBA) is 100°, the MBD size meets the requirements of the pad. When the ICBA was reduced to 70°, the ball bonded point is eccentric. When the ICBA was increased to 120°, the MBD is too large and is connected to the adjacent pad contact. The size of the fish tail of the second bonded point (second bonded point) changed in the same direction as the tip diameter (TD) changes. When the TD is 178 μm, the fish tail shape is regular and symmetrical. When the working face angle (WFA) is 8° and the outer circular radius (OCR) is equal to the diameter of the alloy wire (25.4 μm), the fish tail shape is regular. When the WFA is higher than 11° or the OCR is higher than 30 μm, the fish tail will appear as virtual welding, and when the WFA is less than 4°, the fish tail of the second bonded point will break due to thinning. When the OCR is less than 20 μm, the fish tail of the second bonded point is too long and causes a short circuit.


2020 ◽  
Vol 109 (5-6) ◽  
pp. 1613-1623 ◽  
Author(s):  
Jiansheng Zhang ◽  
Jie Zhou ◽  
Qiuyun Wang ◽  
Guiqian Xiao ◽  
Guozheng Quan

Author(s):  
Xinzhe Yin ◽  
Jiazhi Yang ◽  
Cunbo Jiang ◽  
Anwen Ying ◽  
Zhe Lan ◽  
...  

Algorithms ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 105
Author(s):  
Hsiung-Cheng Lin ◽  
Chung-Hao Cheng

Copper wire is a major conduction material that carries a variety of signals in industry. Presently, automatic wire elongating machines to produce very thin wiresare available for manufacturing. However, the original wires for the elongating process to thin sizes need heating, drawing and then threadingthrough the die molds by the manpower before the machine starts to work. This procedure repeatsuntil the wire threads through all various die molds. To replace the manpower, this paper aims to develop an automatic wire die molds threading system for the wire elongation process. Three pneumatic grippers are designed in the proposed system. The first gripper is used to clamp the wire. The second gripper fixed in the rotating mechanism is to draw the heated wire. The third gripper is used to move the wire for threading through the dies mold. The force designed for drawing the wire can be adjusted via the gear ratio. The experimental results confirm that the proposed system can accomplish the wiredies mold threading processin term of robustness, rapidness and accuracy.


2019 ◽  
Vol 1187 (2) ◽  
pp. 022067
Author(s):  
Ying An-wen ◽  
Yang Jia-zhi ◽  
Yin Xin-zhe
Keyword(s):  

2016 ◽  
Vol 26 (3) ◽  
pp. 1-5 ◽  
Author(s):  
Nobutaka Kito ◽  
Kazuyoshi Takagi ◽  
Naofumi Takagi

Sign in / Sign up

Export Citation Format

Share Document