Applying Slim Dipole Sonic Tool to Evaluate Hydraulic Fracture Geometry and Orientation Using the Differential Sonic Method

2022 ◽  
Author(s):  
Azzan Al-Yaarubi ◽  
Sumaiya Al Bimani ◽  
Sataa Al Rahbi ◽  
Richard Leech ◽  
Dmitrii Smirnov ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Oil Recovery ◽  
Critical Role ◽  
Differential Method ◽  
Optimum Number ◽  
Well Test ◽  
Fracture Geometry ◽  
The Subject ◽  
Fracture Height ◽  
Depth Of Investigation

Abstract Successful hydraulic fracturing is critical for hydrocarbon recovery from tight reservoirs. Fracture geometry is one essential quality indicator of the created fracture. The geometry provides information about the size of the created fracture and containment and verifies the pre-job modeling. Different techniques are applied to determine fracture geometry, and each has its own advantages and limitations. Due to its simplicity, the radioactive tracer log is commonly used to determine fracture placement and fracture height. Its main drawbacks include shallow depth of investigation, time dependency, and the requirement for multiple interventions for multistage fracturing operations. The crosswell microseismic technique probes a larger volume and it is potentially capable of providing fracture height, length, and orientation. Operational complexity and long processing turnaround time are the main challenges of this technique. Time-lapse shear slowness anisotropy analysis is an effective method to determine hydraulic facture height and orientation. In this technique, the shear slowness anisotropy is recorded before and after the fracture is created. The observed shear anisotropy difference indicates the intervals where the fractures were created, allowing these intervals lengths to be measured. Combining this analysis with gyroscopic data allows determining the fracture orientations. Compared to a tracer log, the differential casedhole sonic anisotropy (DCHSA) has a deeper depth of investigation, and it is time independent. Thus, the repeated log can be acquired at the end of the multistage fracturing operations. Compared to the microseismic technique, this new technique provides more precise fracture height and orientation. The new generation slim dipole sonic technology of 2.125-in. diameter extends the applicability of the DCHSA technique to smaller casing sizes. The shear differential method was applied to a vertical well that targeted the Athel formation in the south of the Sultanate of Oman. This formation is made of silicilyte and is characterized by very low permeability of about 0.01 md on average. Thus, hydraulic fracturing plays a critical role for the economic oil recovery in this reservoir. Aiming to achieve a better zonal contribution, the stimulation design was changed from a limited number of large fractures to an extensive multistage fracturing design in the subject well. Sixteen hydraulic fracturing stages were planned. The DCHSA was applied to provide accurate and efficient fracture geometry evaluation. The DCHSA accurately identified fracture intervals and their corresponding heights and orientations. This enabled effectively determining the created fracture quality and helped explain the responses of the production logs that were recorded during the well test. This study provided a foundation for the placement and completion design of the future wells in the subject reservoir. It particularly revealed adequate fracturing intervals and the optimum number of stages required to achieve optimum reservoir coverage and avoid vertical overlapping.

scholarly journals Discrete Element Simulation of Interaction between Hydraulic Fracturing and a Single Natural Fracture

Fluids ◽  
2019 ◽  
Vol 4 (2) ◽  
pp. 76
Author(s):  
Basirat ◽  
Goshtasbi ◽  
Ahmadi
Keyword(s):  
Hydraulic Fracturing ◽  
Fractured Reservoirs ◽  
Critical Role ◽  
Injection Pressure ◽  
Discrete Element ◽  
Natural Fracture ◽  
Effective Parameters ◽  
Fracture Geometry ◽  
Interaction Mode ◽  
Element Simulation

Hydraulic fracturing (HF) treatment is performed to enhance the productivity in the fractured reservoirs. During this process, the interaction between HF and natural fracture (NF) plays a critical role by making it possible to predict fracture geometry and reservoir production. In this paper, interaction modes between HF and NF are simulated using the discrete element method (DEM) and effective parameters on the interaction mechanisms are investigated. The numerical results also are compared with different analytical methods and experimental results. The results showed that HF generally tends to cross the NF at an angle of more than 45° and a moderate differential stress (greater than 5 MPa), and the opening mode is dominated at an angle of fewer than 45°. Two effects of changing in the interaction mode and NF opening were also found by changing the strength parameters of NF. Interaction mode was changed by increasing the friction coefficient, while by increasing the cohesion of NF it was less opened under a constant injection pressure.

Case Study: An Approach for Hydraulic Fracturing Minifrac G-Function Analysis in Relation to Facies Distribution in Multilayered Clastic Reservoirs

2021 ◽  
pp. 1-8
Author(s):  
T. Jatykov ◽  
K. Bimuratkyzy
Keyword(s):  
Hydraulic Fracturing ◽  
Function Analysis ◽  
Flow Regimes ◽  
Fracture Geometry ◽  
Facies Distribution ◽  
Fracture Closure ◽  
Reservoir Conditions ◽  
Fracture Height ◽  
Function Interpretation

Summary An industry-accepted standard for minifrac analysis for evaluating and improving design of hydraulic fracturing treatments originated from the original Nolte analysis (Nolte 1979) of pressure decline, followed by the introduction of Castillo G-function in a Cartesian plot (Castillo 1987). The latter provides a graphical method for the identification of fracture closure pressures and stresses with subsequent derivation of other parameters such as fluid efficiency and fracture geometry. With the introduction of a more advanced consideration of the G-function interpretation for various reservoir conditions (Barree et al. 2007), subdividing the interpretation into calculations based on flow regimes and leakoff modes, this approach has become even more sophisticated. Particularly, interesting flow regimes and leakoff modes during fracture closure include the fracture height recession mode. This mode tends to result in rapid screenout and difficulty in placing high proppant concentrations. Regarding interpretation, the G-function derivative curve for this mode can have more than one plateau, an outcome that is possibly indicative of features that have not been widely considered to date or on which little to no data have been published. This paper presents a case study as an example of such height recession mode, along with a subsequent G-function interpretation and analysis and with consideration of the vertical facies distribution along the wellbore. Considerable attention is paid to the G-function derivative plateau analysis. Three distinctive wells, namely X-1,X-2, and X-3, are discussed. Using this technique can lead to an improved fracture calibration, optimized fracture design, and adoption of a successful completion strategy; additionally, the confirmation of 1D facies distribution can provide new insights into the fracture closure period.

Fracturing With Height Control Extends the Life of Mature Reservoirs in the Pannonian Basin

2021 ◽  
Vol 73 (01) ◽  
pp. 53-54
Author(s):  
Chris Carpenter
Keyword(s):  
Hydraulic Fracturing ◽  
Pannonian Basin ◽  
Oil Production ◽  
High Water ◽  
Economic Feasibility ◽  
Fracture Geometry ◽  
Height Control ◽  
Control Techniques ◽  
Fracture Height ◽  
Water Cut

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper SPE 200588, “Fracturing With Height Control Extends the Life of Mature Reservoirs: Case Studies From the Pannonian Basin,” by Ruslan Malon, SPE, Independent, and Jonathan Abbott, SPE, and Ludmila Belyakova, SPE, Schlumberger, et al., prepared for the 2020 SPE Europec featured at the 82nd EAGE Conference and Exhibition, originally scheduled to be held in Amsterdam, 1-3 December. The paper has not been peer reviewed. Hydraulic proppant fracturing is an effective tool in mature, low-permeability reservoirs found in the Pannonian Basin. However, for wells already producing with high water cut, even a small fracture extension into a water-bearing zone offsets the gains in hydrocarbon production. Fracture-geometry-control (FGC) techniques limit increases in water cut. The complete paper describes the first implementation of a solution to control fracture height for conventional wells in the Pannonian Basin. An integrated engineering approach was applied, including a new proppant-transport model to predict fracture geometry improvement using the FGC solution. Decreased Recovery in A and B Fields Oilfield A began producing in 1984. In addition to an interruption by the war in Yugoslavia in the 1990s, production has been in decline, and most wells are at risk of being shut in because of low production rates. During the last 10 years, propped fracturing was integrated into the production strategy for this mature field. Field A comprises Lower Pontian (Miocene) sandstones. Another sandstone formation exists between 5 and 15 m below the production target reservoir, with high water saturation as confirmed by log analysis and well testing. The proximity of the oil target to the water-bearing interval still presents a risk to production considering that hydraulic fracturing is required to extend field life. An impermeable shale streak that may act as a geomechanical barrier exists below the target formation. With a lower risk of fracture propagation into the water zone, Field A was one of the first candidate fields for propped fracturing and was later considered for advanced fracture-height-control techniques to prevent the increase of water cut after stimulation. Hydraulic fracturing would not be trialed in Field B—the characteristics of which are provided in the complete paper—until the advanced height-control techniques had been proved on the basis of experience with Field A. Oilfield A: Early Fracturing Results Early campaigns proved the economic feasibility of propped fracturing, resulting in a 2.1-fold average increase in oil production during the first 6 months of production. Unfortunately, production after this early period declined rapidly. Increases in water cut, seen in several fracturing campaigns, clearly were related to hydraulic fracture growth. Although the resulting uplift in oil production warranted continued fracturing, avoiding water was a key issue to address before expansion of propped fracturing further in this field and to other fields with an even higher risk of water.

scholarly journals Hydraulic Fracture Geometry Modeling Techniques for Extracting Unconventional Reservoirs

2020 ◽  
pp. 1-5
Author(s):  
Mohamed Ali Khalil ◽  
Abdunaser Omar Susi
Keyword(s):  
Hydraulic Fracturing ◽  
Oil Recovery ◽  
Hydraulic Fracture ◽  
3D Models ◽  
Unconventional Reservoirs ◽  
Fracture Geometry ◽  
Geometry Modeling ◽  
Advantages And Disadvantages ◽  
Modeling Techniques ◽  
Enhance Oil Recovery

This study aims to provide a comprehensive review of all hydraulic fracture geometry modeling techniques available in the conventional and unconventional reservoirs. We are introducing a comparison study between major available hydraulic fracture modeling techniques, advantages, and disadvantages of each one according to the latest related studies. The study includes the three general families of models: 2D models, pseudo-3D models, and fully 3D models. Consequently, the results of this work can be used for selecting the proper model to simulate or stimulate the reservoir to enhance oil recovery using hydraulic fracturing. Also, these results can be used for any future updates related to hydraulic fracturing stimulation based on the comparisons that were conducted.

Integrated Hydraulic Fracture Geometry Evaluation Based on Pre-Cambrian Tight Silicylate Reservoir in South Oman Salt Basin

2022 ◽  
Author(s):  
Dmitrii Smirnov ◽  
Omar AL Isaee ◽  
Alexey Moiseenkov ◽  
Abdullah Al Hadhrami ◽  
Hilal Shabibi ◽  
...  
Keyword(s):  
Best Practices ◽  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Hydraulic Fractures ◽  
Bond Quality ◽  
Fracture Geometry ◽  
Acoustic Anisotropy ◽  
Sonic Log ◽  
Before And After ◽  
Fracture Height

Abstract Pre-Cambrian South Oman tight silicilyte reservoirs are very challenging for the development due to poor permeability less than 0.1 mD and laminated texture. Successful hydraulic fracturing is a key for the long commercial production. One of the main parameter for frac planning and optimization is fracture geometry. The objective of this study was summarizing results comparison from different logging methods and recommended best practices for logging program targeting fracture geometry evaluation. The novel method in the region for hydraulic fracture height and orientation evaluation is cross-dipole cased hole acoustic logging. The method allows to evaluate fracture geometry based on the acoustic anisotropy changes after frac operations in the near wellbore area. The memory sonic log combined with the Gyro was acquired before and after frac operations in the cased hole. The acoustic data was compared with Spectral Noise log, Chemical and Radioactive tracers, Production Logging and pre-frac model. Extensive logging program allow to complete integrated evaluation, define methods limitations and advantages, summarize best practices and optimum logging program for the future wells. The challenges in combining memory cross-dipole sonic log and gyro in cased hole were effectively resolved. The acoustic anisotropy analysis successfully confirms stresses and predominant hydraulic fractures orientation. Fracture height was confirmed based on results from different logging methods. Tracers are well known method for the fracture height evaluation after hydraulic frac operations. The Spectral Noise log is perfect tool to evaluate hydraulically active fracture height in the near wellbore area. The combination of cased hole acoustic and noise logging methods is a powerful complex for hydraulic fracture geometry evaluation. The main limitations and challenges for sonic log are cement bond quality and hole conditions after frac operations. Noise log has limited depth of investigation. However, in combination with production and temperature logging provides reliable fit for purpose capabilities. The abilities of sonic anisotropy analysis for fracture height and hydraulic fracture orientation were confirmed. The optimum logging program for fracture geometry evaluation was defined and recommended for replication in projects were fracture geometry evaluation is required for hydraulic fracturing optimization.

Utilizing Microseismic to Monitor Fracture Geometry in a Horizontal Well in a Tight Sandstone Formation

2021 ◽  
Author(s):  
Abu M. Sani ◽  
Hatim S. AlQasim ◽  
Rayan A. Alidi
Keyword(s):  
Horizontal Well ◽  
Fracture Propagation ◽  
Horizontal Stress ◽  
Height Growth ◽  
Tight Sandstone ◽  
Fracture Geometry ◽  
Fracture Length ◽  
Sandstone Formation ◽  
Fracture Height ◽  
Maximum Horizontal Stress

Abstract This paper presents the use of real-time microseismic (MS) monitoring to understand hydraulic fracturing of a horizontal well drilled in the minimum stress direction within a high-temperature high-pressure (HTHP) tight sandstone formation. The well achieved a reservoir contact of more than 3,500 ft. Careful planning of the monitoring well and treatment well setup enabled capture of high quality MS events resulting in useful information on the regional maximum horizontal stress and offers an understanding of the fracture geometry with respect to clusters and stage spacing in relation to fracture propagation and growth. The maximum horizontal stress based on MS events was found to be different from the expected value with fracture azimuth off by more than 25 degree among the stages. Transverse fracture propagation was observed with overlapping MS events across stages. Upward fracture height growth was dominant in tighter stages. MS fracture length and height in excess of 500 ft and 100 ft, respectively, were created for most of the stages resulting in stimulated volumes that are high. Bigger fracture jobs yielded longer fracture length and were more confined in height growth. MS events fracture lengths and heights were found to be on average 1.36 and 1.30 times, respectively, to those of pressure-match.

No Need for Radio Active Tracer When Mother Nature Helps Detecting the Effective Hydraulic Fracture Height

2022 ◽  
Author(s):  
Rinat Lukmanov ◽  
Said Jabri ◽  
Ehab Ibrahim
Keyword(s):  
Hydraulic Fracture ◽  
Natural Radioactivity ◽  
Gamma Ray ◽  
Fracture Propagation ◽  
Radioactive Isotopes ◽  
Main Element ◽  
Tight Gas ◽  
Well Test ◽  
Gas Reservoirs ◽  
Fracture Height

Abstract The tight gas reservoirs of Haima Supergroup provide the majority of gas production in the Sultanate of Oman. The paper discusses a possibility of using the anomalies from natural radioactivity to evaluate the fracture height for complex tight gas in mature fields of Oman. The standard industry practice is adding radioactive isotopes to the proppant. Spectral Gamma Ray log is used to determine near wellbore traced proppant placement. Spectral Noise log in combination with Production logs helps to identify the active fractures contributing to production. These methods complement each other, but they are obviously associated with costs. Hence, majority of wells are fracced without tracers or any other fracture height diagnostics. However, in several brown fields, an alternative approach to identify fracture height has been developed which provides fit-for-purpose results. It is based on the analysis of naturally occurring radioactive minerals (NORM) precipitation. The anomalies were observed in the many gas reservoirs even in cases when tracers were not used. At certain conditions, these anomalies can be used to characterize fracture propagation and optimize future wells hydraulic Fracture design. A high number of PLTs and well test information were analyzed. Since tight formations normally don't produce without fracturing, radioactive anomalies flag the contributing intervals and hence fracture propagation. The main element of analysis procedure is related to that fact that if no tracers applied, the discrepancy between normalized Open Hole Gamma Ray and Gamma Ray taken during PLT after 6-12 months of production can be used instead to establish fracture height. This method cannot be applied for immediate interpretation of fracture propagation because time is required to precipitate NORM and using the anomalies concept. The advantage of this method is that it can be used in some fields to estimate the frac effectiveness of wells without artificial tracers. It is normally assumed that the Natural radioactivity anomalies appear mainly due to co-production of the formation water. However, in the fields of interest the anomalies appear in wells producing only gas and condensate. This observation provides an opportunity for active fracture height determination at minimum cost.

scholarly journals A new slick water system for hydraulic fracturing in tight reservoir to enhance imbibition oil recovery

2021 ◽  
Vol 303 ◽  
pp. 01001
Author(s):  
Yu Haiyang ◽  
Ji Wenjuan ◽  
Luo Cheng ◽  
Lu Junkai ◽  
Yan Fei ◽  
...  
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Hydraulic Fracturing ◽  
Oil Recovery ◽  
Water System ◽  
Natural Fracture ◽  
Fracturing Fluid ◽  
The Core ◽  
Ultralow Permeability

In order to give full play to the role of imbibition of capillary force and enhance oil recovery of ultralow permeability sandstone reservoir after hydraulic fracturing, the mixed water fracture technology based on functional slick water is described and successfully applied to several wells in oilfield. The core of the technology is determination of influence factors of imbibition oil recovery, the development of new functional slick water system and optimization of volume fracturing parameters. The imbibition results show that it is significant effect of interfacial tension, wetting on imbibition oil recovery. The interfacial tension decreases by an order of magnitude, the imbibition oil recovery reduces by more than 10%. The imbibition oil recovery increases with the contact angle decreasing. The emulsifying ability has no obvious effect on imbibition oil recovery. The functional slick water system considering imbibition is developed based on the solution rheology and polymer chemistry. The system has introduced the active group and temperature resistant group into the polymer molecules. The molecular weight is controlled in 1.5 million. The viscosity is greater than 2mPa·s after shearing 2h under 170s-1 and 100℃. The interfacial tension could decrease to 10-2mN/m. The contact angle decreased from 58° to 22° and the core damage rate is less than 12%. The imbibition oil recovery could reach to 43%. The fracturing process includes slick water stage and linear gel stage. 10% 100 mesh ceramists and 8% temporary plugging agents are carried into the formation by functional slick water. 40-70 mesh ceramists are carried by linear gel. The liquid volume ratio is about 4:1 and the displacement is controlled at 10-12m3/min. The sand content and fracturing fluid volumes of single stage are 80m3 and 2500 m3 respectively. Compared with conventional fracturing, due to imbibition oil recovery, there is only 25% of the fracturing fluid flowback rate when the crude oil flew out. When the oil well is in normal production, about 50% of the fracturing fluid is not returned. It is useful to maintain the formation energy and slow down the production decline. The average cumulative production of vertical wells is greater than 2800t, and the effective period is more than 2 years. This technology overcoming the problem of high horizontal stress difference and lack of natural fracture has been successfully applied in Jidong Oilfield ultralow permeability reservoir. The successful application of this technology not only helps to promote the effective use of ultralow permeability reservoirs, but also helps to further clarify the role of imbibition recovery, energy storage and oil-water replacement mechanism.

scholarly journals OPTIMISATION OF HYDRAULIC FRACTURING DESIGN IN LOWER OLIGOCENE RESERVOIR, KINH NGU TRANG OILFIELD

2018 ◽  
Vol 18 (3) ◽  
pp. 323-337
Author(s):  
Nguyen Huu Truong
Keyword(s):  
Hydraulic Fracturing ◽  
Complex Structure ◽  
Power Requirement ◽  
Fracture Conductivity ◽  
Fracture Width ◽  
The North ◽  
Fracture Closure ◽  
Average Water ◽  
White Tiger ◽  
Fracture Height

Kinh Ngu Trang oilfield is of the block 09-2/09 offshore Vietnam, which is located in the Cuu Long basin, the distance from that field to Port of Vung Tau is around 140 km and it is about 14 km from the north of Rang Dong oilfield of the block 15.2, and around 50 km from the east of White Tiger in the block 09.1. That block accounts for total area of 992 km2 with the average water depth of around 50 m to 70 m. The characteristic of Oligocene E reservoir is tight oil in sandstone, very complicated with complex structure. Therefore, the big challenges in this reservoir are the low permeability and the low porosity of around 0.2 md to less than 1 md and 1% to less than 13%, respectively, leading to very low fracture conductivity among the fractures. Through the Minifrac test for reservoir with reservoir depth from 3,501 mMD to 3,525 mMD, the total leak-off coefficient and fracture closure pressure were determined as 0.005 ft/min0.5 and 9,100 psi, respectively. To create new fracture dimensions, hydraulic fracturing stimulation has been used to stimulate this reservoir, including proppant selection and fluid selection, pump power requirement. In this article, the authors present optimisation of hydraulic fracturing design using unified fracture design, the results show that optimum fracture dimensions include fracture half-length, fracture width and fracture height of 216 m, 0.34 inches and 31 m, respectively when using proppant mass of 150,000 lbs of 20/40 ISP Carbolite Ceramic proppant.

Sign in / Sign up

Export Citation Format

Share Document