Behavior of Some Tungsten Carbide Coatings in Molten Zinc

1996 ◽  
Author(s):  
A.J. Stavros
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tungsten Carbide ◽  
The Other ◽  
Time To Failure ◽  
X Ray Diffraction ◽  
Molten Zinc ◽  
X Ray ◽  
Carbide Coatings ◽  
Scanning Electron

Abstract Two different W-Co-C powders were used in three deposition devices, the Super D-Gun, Jet Kote, and JP-5000 to produce coatings for laboratory immersion tests in molten zinc and %55Al-Zn. Resistance was evaluated as time to failure. Scanning electron microscopy and X-ray diffraction were used to characterize the structures ssid failure mechanism. All coatings were found to fail when the molten metal breached the coating thickness at weak spots and spread out over the underlying interface to lift the coating away from the underlying 316L substrate. These weak spots were "pits" on one Super D-Gun coating (the most resistant coating) and cracks on all the other coatings. No diffusion of zinc through the tungsten carbide coatings was observed.

scholarly journals Synthesis of Zeolite A employing Amazon kaolin waste

Cerâmica ◽  
2015 ◽  
Vol 61 (360) ◽  
pp. 409-413 ◽  
Author(s):  
S. H. da Silva Filho ◽  
L. Bieseki ◽  
A. R. da Silva ◽  
A. A. B. Maia ◽  
R. A. S. San Gil ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Amorphous Materials ◽  
Mas Nmr ◽  
The Other ◽  
Zeolite A ◽  
X Ray Diffraction ◽  
X Ray ◽  
27Al Mas Nmr ◽  
Scanning Electron

Abstract The synthesis of zeolite A employing kaolin waste from paper coating was studied. The kaolin waste was pre-treated at 550 to 800 ºC. For comparison purposes, a sample of zeolite A was also prepared using the IZA procedure. The materials were characterized by 27Al MAS NMR, X-ray diffraction and scanning electron microscopy using a microprobe. Pretreatment was necessary, and the best temperatures were between 600 and 700 ºC. The zeolite A formation was observed in all the prepared materials, reaching 52% crystallinity. On the other hand, the sodalite phase and amorphous materials were also formed.

Template-Free Synthesis of α-Fe2O3 Hollow Spheres and Nanocubes

2011 ◽  
Vol 361-363 ◽  
pp. 2012-2015
Author(s):  
Chang Yun Chen ◽  
Feng Zhou ◽  
Chun Hua ◽  
Zhao Hui Li ◽  
Huan Pang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Hollow Spheres ◽  
Magnetic Characteristic ◽  
The Other ◽  
X Ray Diffraction ◽  
Facile Hydrothermal Method ◽  
X Ray ◽  
Template Free ◽  
Scanning Electron

A facile hydrothermal method without any templates has been developed for the preparation of α- Fe2O3nanocubes and hollow spheres. The as-synthesized products is then characterized using X-ray diffraction(XRD), scanning electron microscopy(SEM). The nanocubes have extraordinary unity and we can anticipate its unique magnetic characteristic. On the other hand, the hollow sphere structure has a promising future in the application as carriers for targeting drug delivery. In our opinions, the method is not only very simple, but also is very friendly to the environment.

Structure and Composition of Rhinoceros Horn

1992 ◽  
Vol 292 ◽  
Author(s):  
Ann Chidester Van Orden ◽  
Joseph C. Daniel
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Breeding Success ◽  
The Other ◽  
X Ray Diffraction ◽  
Structural Morphology ◽  
X Ray ◽  
Metal Ceramic ◽  
Scanning Electron

AbstractRhinoceros horn has been used medicinally and as a talisman in many cultures and animals are slaughtered to obtain the horn. With the dwindling populations of rhinos, and the limited number and breeding success of captive rhinos, there is a critical need to learn as much as is possible about their horns to find an adequate substitute. Examination of rhino horn was made using optical microscopy, scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and x-ray diffraction (XRD). The structure of the horn is unusual and consists of two separate phases, one of hair-like filaments, built around a central core in circumferential layers and the other surrounding and filling in the spaces between the filaments as a matrix. Together, these two structures make up a biological composite, structurally similar to metal, ceramic or polymer based composites. The structural morphology, the dimensions of the structures, and the chemistry of the horn are discussed. Comparisons are made between horn, hoof, and hair of rhinos and hoof and hair from horses, their nearest living relatives.

Influence of Microwave Sintering Environment on the Preparation of AlN Powder and Ceramic

2008 ◽  
Vol 368-372 ◽  
pp. 967-969
Author(s):  
Xiao Feng Zeng ◽  
Duan Fen Qian ◽  
Hu Peng ◽  
Wei Feng Li ◽  
Xuan Yong Liu
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Microwave Sintering ◽  
Great Influence ◽  
The Other ◽  
Mechanical And Thermal Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Material Fabrication ◽  
Scanning Electron

In this paper, AlN powder and ceramic are prepared by microwave sintering under various sintering environments. The microstructures of the powder and the ceramic are characterized by scanning electron microscopy and X-ray diffraction technology. The mechanical and thermal properties of the ceramic are studied. It was found that the sintering environment has great influence on the material fabrication. The heat-assisted environment is beneficial to the synthesis of AlN powder. On the other hand, the carbothermal sintering environment has the two-sided influence to the sintering of AlN ceramic.

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Environmental scanning electron microscopy of fresh human gallstones reveals new morphologies of precipitated calcium salts

1992 ◽  
Vol 50 (2) ◽  
pp. 1322-1323
Author(s):  
Howard S. Kaufman ◽  
Keith D. Lillemoe ◽  
John T. Mastovich ◽  
Henry A. Pitt
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Scanning Electron Microscopy ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
Calcium Salts ◽  
Cholesterol Gallstones ◽  
X Ray ◽  
Ca Carbonate ◽  
Scanning Electron

Gallstones contain precipitated cholesterol, calcium salts, and proteins. Calcium (Ca) bilirubinate, palmitate, phosphate, and carbonate occurring in gallstones have variable morphologies but characteristic windowless energy dispersive x-ray (EDX) spectra. Previous studies of gallstone microstructure and composition using scanning electron microscopy (SEM) with EDX have been limited to dehydrated samples. In this state, Ca bilirubinates appear as either glassy masses, which predominate in black pigment stones, or as clusters, which are found mostly in cholesterol gallstones. The three polymorphs of Ca carbonate, calcite, vaterite, and aragonite, have been identified in gallstones by x-ray diffraction, however; the morphologies of these crystals vary in the literature. The purpose of this experiment was to study fresh gallstones by environmental SEM (ESEM) to determine if dehydration affects gallstone Ca salt morphology.Gallstones and bile were obtained fresh at cholecystectomy from 6 patients. To prevent dehydration, stones were stored in bile at 37°C. All samples were studied within 4 days of procurement.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Structural Characterization of Gallbladder Stones Using Energy Dispersive X-ray Spectroscopy and X-ray Diffraction

2018 ◽  
Vol 21 (7) ◽  
pp. 495-500 ◽  
Author(s):  
Hassan A. Almarshad ◽  
Sayed M. Badawy ◽  
Abdalkarem F. Alsharari
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Energy Dispersive ◽  
Spectroscopic Techniques ◽  
X Ray Diffraction ◽  
Major Health Problem ◽  
X Ray ◽  
Gallbladder Stones ◽  
Pure Cholesterol ◽  
Scanning Electron

Aim and Objective: Formation of the gallbladder stones is a common disease and a major health problem. The present study aimed to identify the structures of the most common types of gallbladder stones using X-ray spectroscopic techniques, which provide information about the process of stone formation. Material and Method: Phase and elemental compositions of pure cholesterol and mixed gallstones removed from gallbladders of patients were studied using energy-dispersive X-ray spectroscopy combined with scanning electron microscopy analysis and X-ray diffraction. Results: The crystal structures of gallstones which coincide with standard patterns were confirmed by X-ray diffraction. Plate-like cholesterol crystals with laminar shaped and thin layered structures were clearly observed for gallstone of pure cholesterol by scanning electron microscopy; it also revealed different morphologies from mixed cholesterol stones. Elemental analysis of pure cholesterol and mixed gallstones using energy-dispersive X-ray spectroscopy confirmed the different formation processes of the different types of gallstones. Conclusion: The method of fast and reliable X-ray spectroscopic techniques has numerous advantages over the traditional chemical analysis and other analytical techniques. The results also revealed that the X-ray spectroscopy technique is a promising technique that can aid in understanding the pathogenesis of gallstone disease.

scholarly journals Analytical study of Buddha sculptures in Jingyin temple of Taiyuan, China

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Xiaojian Bai ◽  
Chen Jia ◽  
Zhigen Chen ◽  
Yuxuan Gong ◽  
Huwei Cheng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Analytical Study ◽  
Energy Dispersive Spectrometry ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Ancient China ◽  
X Ray ◽  
Unique Style ◽  
Scanning Electron

AbstractWith exquisite design and unique style, the painted sculptures of Tutang Buddha and two attendants Buddha in Jingyin Temple are precious cultural heritages of China. The sculpture of Tutang Buddha, which was carved from a mound and painted by ancient craftsmen, was rarely found in ancient China. However, due to natural and human factors, the sculptures were severely damaged. Obviously, they require urgent and appropriate protection and restoration. In this study, samples taken from the sculptures were analysed through multiple analytical techniques, including scanning electron microscopy with energy dispersive spectrometry (SEM–EDS), Raman spectroscopy, X-ray diffraction (XRD), optical microscopy (OM) and granulometry. The analysis results enable us to infer the techniques used by the craftsmen in making the sculptures and provide a reliable evidence for the conservation and future protection of these and similar sculptures.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Sign in / Sign up

Export Citation Format

Share Document